Enabling CIR driver for UART2 for DM81xx
Hi, I am trying to make the CIR driver work on UART2 for DM8107 for DVR. I am using DM810x DVR RDK release 3.00.01.26, using the...
View Articletying DVO2 and HDMI in RDK 3.2 MCFW
Dear All,I am working with a custom board using DM8148 TI CPU. For the first time, I try our board with ezsdk and the psp examples to test HDMI and DVO2 output. We success-ed to tie HDMI and DVO2 to...
View ArticleProblem with eUSCI_A ISR with MSP430F6733
HelloI'm working on a project that utilises eUSCI_A1 in UART mode. I'm having a problem with the ISR. It works fine when receiving, but the TX interrupt does not trigger the ISR. TX interrupt is...
View ArticleTMS470MF03107 go to the sleep mode. How much is the power consumption ???
Dear Sir,TMS470MF03107 go to the sleep mode. How much is the power consumption ???I have checked this TMS470MF04207/TMS470MF03107 16/32-Bit RISC Flash Microcontroller (Rev. C) : SPNS15C.PDF . This PDF...
View ArticleStellaris PWM interrupt skipping
Dear Sirs,I have a motion control application, where I need to push the PWM frequency up to 64Khz or more.The current loop computation should remain at 8Khz., so I need to process exactly one interrupt...
View ArticleTrouble with the MSP-EXP430F5529 Experimenter Board PCB Design Files
Hi there,I am currently working with the MSP-EXP430F5529 Experimenter Board (http://www.ti.com/tool/msp-exp430f5529) and wanted to import the schematics into DesignSpark, which I am using to create...
View ArticleActive USB 3.0 cable with two sn65LVPE502
Hello,I'd like to know whether it's possible to use two sn65lvpe502 devices to build an active USB 3.0 cable. The idea is to re-drive the signals from both host and device side. The signal quality...
View ArticleCC1101 Receiving sensitivity and Layout
There is one question about CC1101.1. There are inequalities in the measured values compared to the data sheet spec. In order to increase the receiver sensitivity, is there any way? (I want to...
View ArticleC553x Memory-Mapped Registers for Boot-Time Register Configuration
Hi,Document SPRUH87C page 99 says the LDO Control Register is at 0x7004. However, document SPRS737B page 19 says the address range 0x3B2F ~ 0x7FFF of C5533/4 is reserved, yet address range 0x7000 ~...
View Articleproblem PCIe link training eval6678
Hello,I am trying to connect two eval6678 through a MICROTCA backplane, loading the PCIe example program and configuring one board as root complex and the other one as endpoint. The Endpoint succeeds...
View ArticleDEI OMX Component issue
Hi,I am trying to Encode two h264 streams, with the single capture.for this i have created and connected the Omx componet in the following manner YUV 420 YUV...
View ArticleRDK vs. EZSDK
Hello,My hardware is composed of tvp5158 into VIN1 and tvp7002 into VIN2. what is the right developing software package in my case ? rdk or ezsdk ?if I am using "ezsdk overlay" (ezsdk with change to...
View ArticleProblem with Spy-bi-wire programming
I am using the demo board MSP-TS430RGZ48C with a MSP430FR5969 and the debugger MSP-FET430UIF. For programming the device, I use the last IAR version (5.51.3). When I place the Jumper JP3, JP4, JP5,...
View ArticleGetting Started with PAN1326 and A2DP
Hello, I'm looking to use the A2DP protocol for a Bluetooth application for a PAN1326 chip. I have C and C++ programming experience but have never programmed for Bluetooth before. What do I need to...
View ArticleProblem with 3G-SDI RX
Hi ,We are using LMH0303 & LMH0344 in the TX and RX paths of SDI respectively.SDI TX is working without any issues for all modes (SD-SDI , HD-SDI , 3G-SDI & Dual stream SDI ). We have verified...
View ArticleSwitcherPro Desktop Design List data transfer
I want to transfer Design List data to another PC.Is it possible?If possible, which data file should I transfer?
View ArticleTPS65950 starting events
We require TPS65950 to start on when main power is applied to it as we are not using PWR on button to turn it on.We understand the PMIC will start up as the power is applied to it but this is due to...
View ArticleMSP-GANG Programmer Vcc problem
Hello,I have trouble using the MSP-GANG Programmer + MSP-GANG Splitter. When toggling the Vcc on/off in the MSP-GANG Programmer software, I measure the voltage go on and off on pin#12 on the JTAG/BSL...
View ArticleClik here to view.
Murata's CC3000 TB current spike issue
Hello everyone,I am facing a quite bad behavior using CC3000 + MSP430FR dev kit. When I debug a project using CCS, as soon as I enable the module by bringing EN pin high, the CC3000 module drains quite...
View ArticleHow do I read the IDCODE? (absolute beginner)
Let me start by saying I have never touched any type of DSP/FPGA or anything like that so I have no idea what I'm doing. Though I have been reading a lot and really just used this forum as a last...
View Article