How to make a non-interruptible port interruptible...
Hello!The Details:CC430F6137, custom hardware (extremely low power 5-400uA), CCS, USB FETBackground:I made a boo-boo in my hardware design and now realize now that I need to make the I/O on port 5.4...
View Articlehow to use the resizer correctly in decode demo? I have try resizer_config...
Hi,Guys.Device is DM365, DVSDK-demos is 4.0.0.21, DMAI is 2.2.0.14 .Now I can display video in a 800x480 LCD, but since the display thread is using framecopy, the video can only be shown a part of...
View Articlehow to use the resizer correctly in decode demo? I have try resizer_config...
Hi,Guys.Device is DM365, DVSDK-demos is 4.0.0.21, DMAI is 2.2.0.14 .Now I can display video in a 800x480 LCD, but since the display thread is using framecopy, the video can only be shown a part of...
View ArticleMSP430Flasher.exe MSP430F2617 Questions
Hi All,I am attempting to use the MSP430Flasher.exe command line tool to program some MSP430F2617 microcontrollers. It seems to work fine however I have a couple of questions.Firstly I always seem to...
View Articlepcie_boot helloworld example doesn't work
Hi,everyoneI m having an issue using pcie_boot helloworld example to awake core1 from halt. I just added some LED operation in the project, but it seems not working. What could be the problem then?by...
View ArticleGPIO pins on DVDD_M seem to not work properly
I have noticed on pins W2 and V1 I can not control the GPIO1[9] or GPIO1[8]. I have double check the pin mux values and they are correct. Is there a know problem with controlling these gpios on the...
View ArticleLinux for 6657LS ECM?
Is a Linux version available for the 6657ls Evm??looking on Linux-c6x.org it is not supported and not listed in the Linux-c6x makefile....regardsanthony
View Articlecc2530 consumption
I am trying to us chip cc2530 in low power mode.To test it I use the following code:file "rsa_main.c":int main(void) { while (true) { halSleep(0); }; return 0;}When running this code on device and...
View ArticleBug: ADC Sequence not possible under z-stack lighting.
Hi,It is imposible to do a simple ADC sequence when the RF stack is running. Well, the ADC sequence works, but Z_Stack does not anymore (device does not join network). Reproduce it by:HalADCInit APCFG...
View Articlehow to start openMP programing??
hello: if i want to use openmP programming ,so what can support openmP programming? my ccs is ccs5.3. but there is not corresponding openmP directory in the CCS install directory. does not ccs5.3...
View ArticleCC430 Reset Problem
Hi all,I'm busy with a development on a CC430F6137My hardware configuration is as below:1) Digital VCC = AVCC = RF VCC = 2.88 volt (regulator with Imax 200mA)2) DCO enabled in software with 12MHz Clock...
View ArticlerequestOperator must not return error when radio is on:Android ICS on...
Why am i getting this error?I have ported android ICS to beagleboard XM and using a GSM modem for communication purpose.D/AT ( 1034): AT< +COPS: 0,0,"IDEA Cellular Limited"D/AT ( 1034): AT<...
View Articlecharger connection
Hello,It is given in the technical document of bq77910A about charger connection, that whenever thhe charger attached to the system , I t is needed to aatach a resistor to CHGCTL pin to make the IC...
View ArticleIs there a separate TCM Hard Error Cache [64-Bit] for ATCM, B0TCM and B1TCM?
Hello Support,Within TMS570LS Cortex-R4 core, is there a separate 64-Bit TCM Hard Error Cache for each of the TCM interface ports or a single 64 Bit TCM Hard Error Cache for all the 3 TCM Ports [ATCM,...
View ArticleColor space conversion for 8168
now we capture embedded data, input data is 8bit yuv422, if output is yuv output buf video is correct ,when output is rgb888, video utput buf video is not correct ,vip modules cannot conver yuv422...
View Articleuse L2 cache on the dsp side of DM8168
Hello,I am working on dm8168evm with ezsdk5.05.I want to capture 720p60 video frames and do some process on the dsp side,then transmit it back to display.I have modified the saLoopBack(linux example)...
View ArticlePins not defined in the BSDL Model
We are now working on ICT test for AM3352.In the BSDL model for AM335x ZCZ we cannot find the following pins: A5,B4,C10,D10,D6,D9,D11,E7,H15,J4,M5,P15,R10,T18,V11, some of which I found are GND or...
View ArticleWinCE 7 BSP building XLDR for Beagleboard
Hello, I'm using the WinCE 7 BSP from Adeneo website building the XLDR for Beagleboard, but it works abnormally, below is the details. 1. I download the BSP (AM335x_WEC7 Source BSP) and opened in...
View ArticleClik here to view.
Qeustion about RemoteTI Power Consumption
Hi,everyone I have read the Application Note AN076 about RemoteTI Power Consumption written by stig Torud.I have some questions.In the note,there is a way to calculate the life of a battery,I...
View ArticleUnable to load firmware for RDK.4
Hi,We have a customize board, which contains DM8148 & we are using RDK-4.0.We are able to boot the kernel,Also I am able to run init.sh script of RDK,But when I run load.sh , I am getting following...
View Article