TAS5518-5261K2evm 2 channel audio output, can I connect 1 load to the...
I would like to drive 32 Vrms into a 10 ohm load with the EVM ~ 108 W. Can I connect the L & R channel together to increase the max power? I would like to drive load with minimum distortion ( no...
View ArticleAM1808 usb0 can't detect device
Hi,I'm using a USB 2.0 ethernet adapter.When boot 3.2.0, the kernel could not detect the device, only print message like this:......musb_hdrc: version 6.0, ?dma?, otg (peripheral+host)Waiting for USB...
View ArticleClik here to view.
CCS v5.4.0 RC installation error
Hi,the installation crashes with the following error on my system:Installation log:05/06/2013 07:45:50AM - percent now 405/06/2013 07:45:50AM - Processing DS to install05/06/2013 07:45:50AM -...
View ArticleAM335x EVM configuration profile information - where to find? Apparent link...
I am attempting to try out the AM335x general EVM board, and it uses a CPLD to switch pins around, giving eight different peripheral configurations.However, the user manual doesn't say what those eight...
View Articlechanging advertisement rate to 20ms for first 30 sec. on cc2540
I have developed an iphone app using Xcode which uses the connectBlue OLP425 module which includes the cc2540 chip. I have everything working well; when the app is launched it pairs with the module...
View ArticleDDR3 ISSUE IN TMS320C6678
Dear all,We are using the same DDR3 part numbers on both your Rev2.0 and Rev1.0 boards.In our third customized board Both the DSP(C6678) processors are REV-2.0. I can't able to access the 3rd DDR3 chip...
View ArticleDDR3 Intialization
(Please visit the site to view this file)(Please visit the site to view this file)Hi, We have planed to manufacture new board with TMS320C6678. I have described the problem we face in the last bord...
View ArticleezDSP 5535
Hi all,I'm facing some unexpected issues with a ezdsp5535 that I recently purchased and I hope that someone here might have some help to provide.I performed the normal CCS4 install (under windows 8...
View ArticleRSSI and TX Power info in CC2540/CC2541
Hi,Please recommend the best way to access the RSSI and TX Power Level info in the CC2540/CC2541 from a BLE application.If you already have the snippet of this code to copy and paste, it would be...
View ArticleHow to put a array in the absolute flash address under CCS v5.3
Hi, I'm new user for CCS V5.3. I have programmed MSP430 firmware using IAR3.3 workbench for several years, I try to convert my current IAR project to CCS, but there are lots of errors happen, so I have...
View ArticleMSP430 ethernet connectivity.
hi, I am using MSP430 along with ethernet controller CS8900. I need to connect the controller to PC through ethernet. I am able to send data to PC through ethernet, (i am using olimax easy - web...
View ArticleHDMI - Cell phone MHL to V-by-One
Hello,I'm in need a circuit that can take HDMI (specifically MHL from a cell phone) and translate it to V-by-One. From what I can tell V-by-one is only supported by Thine so what I need is HDMI to bus...
View ArticleClik here to view.
F28M35x project : want to connect a 8-wires cable
Hi everyone,I'm a student at a Université of Grenoble, and i do an internship on a F28M35x (F28M35H52C1).For the moment, i need to connect a 8-wires cable on the controlCARD of my F28M35x...
View ArticlePMSM motor control
Hello,I want to bay the DRV 8301 ore the 8312 kit to lurn to program and use it for the existing high part (MOSFET'S) of my old controllers now. Though these controllers can switch 72 to 90 V and 500...
View ArticleCCS5.1 could not open file
We wrote a program that has debug, but why when we load it，the ccs5.1 say “could not open file”？
View ArticleIIC eeprom burning problem for c5505
Hi all,I have a problem when burning the bin file into 5505 E2PROM.The error is followed:Choose the device...0XX - CPLD setup only1x - NAND Flash [CSx: 2,3,4,5]2x - NOR Flash [CSx: 2,3,4,5]3x - SPI...
View Articlemoving code from CONCERTO (Cortex-M3) to HERCULES (RM46)
Hello everyone,I don't have big experience in programing, but I have task to do...I need 'to move' code from Cortex-M3 part of CONCERTO (F28M35H52C) to HERCULES (RM46L852). Could you tell me if it is...
View ArticleBasic Timer Interrupts don't work at higher clock speeds
I'm working on a MSP430FG4618 experiment's board.Basic timer interrupts work fine with a 7 Mhz MCLK but when I crank it upto 13 Mhz , no more interrupts.
View ArticlePUR and USB D+ pull-up during enumeration
On a USB transceiver, is it required for the D+ line to be connected to the PUR pin? Or can the D+ line be pulled up to an external +3.3V net?I am trying to troubleshoot an issue with a custom...
View ArticleRTSC new platform problem in CCS v5.4
I have an LCDKOMAPL138 and I'm trying to make a hello world program that runs concurrently on both cores. I'm using a sysbios typical project template. I can view and even use the LCDKOMAPL138...
View Article