OMAPL138B-EP: OMAPL138EZWTA3 L1\ L2 Cache speed
Part Number:OMAPL138B-EPHi,We are using OMAPL138EZWTA3 OMAP processor in our design. I couldn't find L1 \ L2 Cache memory speed neither in datasheet nor in Manual. Please advise what is the L1 \ L2...
View ArticleDesign calculations
Can you please give me the component design calculations file of this PMP8740.What is the low side output voltage of this design?Thanks.
View ArticleTUSB4041I-Q1: if can read out TUSB4041I-Q1 power switch fail (over current or...
Part Number:TUSB4041I-Q1Hi, Team:Can you help to check if can read out TUSB4041I-Q1 power switch fail (over current or short circuit) from IIC interface?The application use external BC1.2 controller...
View ArticleClik here to view.
Compiler/TMS320F28379D: 2837x_RFFT_ADC
Part Number:TMS320F28379DTool/software: TI C/C++ CompilerHi,I am new to TMS320F28379D , these are a few doubts i have ...1.what is the input and output buffer of this program?2.How to make a...
View ArticleCC1352P: LAUNCHXL-CC1352P-2 Design Files Altium format
Part Number:CC1352PHello Simon,Could you please convert also this BRD inside this zip File www.ti.com/.../getliterature.tsp to . ALG file.We want to use the Balun instead of external filtersThanks in...
View ArticleBQ34Z100-G1: Using a NTC different from the 103AT type specified in the...
Part Number:BQ34Z100-G1Hello all,I'm planing to incorporate the BQ34Z100-G1 gas gauge in an up coming BMS design. Because if legacy stock, and the fact that they are used in different places of the...
View ArticleRTOS/TDA2EVM5777: Questions about IPC 3.45 & it's usage in...
Part Number:TDA2EVM5777Tool/software: TI-RTOSDear TII am new in the TI products. By learning processor vision sdk, i have some questions about how to use ipc APIs to achieve efficient data transport...
View ArticleLMX2491: Selecting PLL spot frequency resolution(in terms of hz, CW Mode)
Part Number:LMX2491Dear all,We are trying to make the PLL to operate in particular frequency per say X Hz, After some time we want to change to X+delta Hz. What is the minimum delta Hz Possible with...
View ArticleUCC2897A: PMP5123 modification for Input voltage:6 to 36V & Output: 12V/10A
Part Number:UCC2897AHi, Is it possible to use UCC2897A for 6V to 36V ? If so, could you suggest changes needed in PMP5123 design ?I believe, output of 12V @ 10A should be achievable.
View ArticleCC3200: wrong date-time calculation from SNTP
Part Number:CC3200Hello all,I am using cc3200 controller. In my application I am using SNTP time to feed my RTC. Now, I am facing problem with the SNTP time coming from the ntp server, it is showing...
View ArticleCC3200MOD: How to enable Uart1 interrupt
Part Number:CC3200MODHi, Can anyone please share me how to enable the UART1 Interrupt for CC3200MOD. If possible share your code or your files. pleaseThanks and RegardsManish Kumar Thakur
View ArticleAMC7834: CLAMP Configuration (0x17) R/W problem
Part Number:AMC7834Should all of the bits 0..6 in CLAMP Configuration (0x17) be readable to indicate their status? I find that Bit 6 (PAON) does change to reflect its status, but the lower Bits 0..5...
View Articlesend data over 5km wire length possible?
I have digital data over uart, which need to be sent over 5km wire length. Digital data I can cnvert to any protocol like spi, i2c or any other or even single wire.RS485 has limitation for 5Km. No...
View ArticlePCM5142: Purepath software
Part Number:PCM5142I purchased a Allo Piano 2.1 DAC which has (2) PCM5142 on it. I need the purepath software to configure the DSP. I have requested it twice, both times denied, because "email doesn't...
View ArticleCC2430: SmartRF Studio 7 is not showing "not connected"
Part Number:CC2430SmartRF Studio 7 is not showing "not connected"in the status. Also the menu items are greyed out. I have installed all drivers. There is no Cebal driver showing in Device Manager? I...
View ArticleClik here to view.
TM4C1230E6PM: JTAG Daisy chain configuration
Part Number:TM4C1230E6PMHi community,Please help me to find the solution for the below queries:1) Please provide the brief information about the JTAG daisy chain configuration.We are using TI CC1352...
View ArticleClik here to view.
TM4C1237E6PM: Voltage level mismatch
Part Number:TM4C1237E6PMHi community,Please help me to find out the answer for the below queries1)IO sink currentI have connected 2# LED Cathode through current limiting resistor (150E) to PE1 and PE5...
View ArticleClik here to view.
CC1310: Change the default 433M to 470-510Mband, how to modify in 15.4 Stack?
Part Number:CC1310Hi,Any guidance to change the frequency band in 15.4Stack? Target frequency band is 470-510M.From below link, seem to we provided a solution,Can you send this ref project to me too?
View ArticleMSP430FR6972: Does Controller enter LPM if one of the GPIOs is driven high?
Part Number:MSP430FR6972Hello I have an application wherein I am supposed to detect the voltage of my main battery using ADC pin and once it drops beyond a value, i want to turn on a mosfet from my...
View ArticleRTOS/CC3220SF-LAUNCHXL: Error(-12 ) Connecting to AWS IOT Core using...
Part Number:CC3220SF-LAUNCHXLTool/software: TI-RTOSHello,Recently i program the CC3220SF-LAUNCHXL with Subscribe_publish_sample program to connect to the AWS IOT Core. But i cannot able to connect the...
View Article