LM57 V(TEMP) Design Considerations
I would like to design a simple board which controls a resistor as a heater. At T(1), heater (resistor) will be ON and at T(2), heater will be OFF and T(1)<T(2).I can set the R(SENSE) and hysteresis...
View ArticleDC input impedance in case of AC-lead-off detection
Hi,with regard to the dc input impedance, in the electrical characteristics table of the ads129x datasheet a distinction is made between current source lead-off detection and pull-up resistor lead-off...
View ArticleSuggestion for Stepper reference?
Greetings!Does anyone have any suggestions for a reference book on using stepper motors? In particular, one that covers how to develop a proper acceleration ramp.Gerry Belanger
View ArticleHow is TLK3134 configured for 10G Ethernet application?
We want to use TLK3414 to implement 10Ge between FPGA and Computer.But as its output is XAUI, so if we use fibre method, then one XAUI->SFI, and one SFP+ module is needed, it's very cost. And I have...
View ArticleBuild SysLink 2.2x examples in CCSv5
Hi,thanks to your help I can run SysLink 2.2x examples on OMAP3530, builded in command line. Now I'd like to use CCSv5 for SysLink project, I supose it could be easier to understand it.So I have to ask...
View ArticleADS1271EVM-PDK: Can't detect the input signal
Hello,I am a customer of ADS1271EVM-PDK,I connect the MMB0 board with 1271EVM and power the system with DC 6V .when I connected this system with PC(OS:windows XP) ,It was shown that "Firmware loaded...
View ArticleRobust I2C Error Handling
Hello all,I am trying to ensure my I2C communication is as robust as possible. In particular, I am now looking at a case where a Master MSP430 communicates with multiple slave devices. I am considering...
View Article[PGA280 + ADS1259] Crosstalk and other questions
Hi !!I'm using PGA280 + ADS1259 solution in an analog voltage/current input system. I have multiple input ports, each one with a RC filter at input stage and connected to external multiplexers....
View Article.apk file to support CC3000FRAMEMK-L Out of Box Demos
Texas Instruments SimpleLink Wi-Fi Support,Thanks in advance for your help. The CC3000 Wi-Fi MSP430 FRAM WIKI page mentions the availability of Android .apk files to support out of box demos on the...
View ArticleXCLKOUT and BOOT_3 conflict in concerto
Hello,I want to use concerto in a PCB design. However, I noted a conflict on pin 82 of F28M35H52C. This pin can be configured as Clock out and also boot mode selection. Since I want to configure to...
View ArticleCSI Sensor integration in OMAP4460: Not getting interrupts for line...
Hi all,I am integrating a new sensor (RAW10) with OMAP4460.I have used V4L2 based driver to do so, I can see expected clock and data signals after configuring sensor.However, I don't get ISS interrupts...
View ArticleConnecting a CC1101EMK to a MSP4302231
Hi there TI community, I am currently wondering the proper way to connect a CC1101 EMK to a MSP4302231. My research has led me to believe that I need to code the MSP430 with TI's SimpliciTI wireless...
View ArticleRequire to transmit fast ethernet signals with recovered clock for 100BaseFX...
Which Phyter chip I can use for operating it in a way where the ethernet received clock can be used for transmitting ethernet signals, instead of using the crystal clock for this purpose. Also would...
View ArticleADC to radio to PC, int (int16) to char (uint8) and back to int (int16)...
Hi,I am trying to write a code to ADC a sine wave and then radio it to a cc2511 dongle acting as a serial port to a PC, so that I can plot and re-create the sine wave at the PC. Now I am really getting...
View ArticleDM8168 DEI LINK scale output failure
Hi allI develop on dm8168 evm board + vs child board using dvrrdk 2.80,i capture a XGA 60 progressive video ,and i want to use dei link to get three channel video ,1,xga 60 for display2. xga 60 for...
View ArticleTPA3116D2 mono
Is there a way to switch between mono and stereo without powering down completely?
View Articledownloading dvsdk_3_10_00_16 source code
hii All,I have been trying to search for the download page of dvsdk_3_10_00_16, which is not the latest version.When i search for dvsdk_3_10_00_16 download, the only download page available is that of...
View ArticleNot seeing expected frame rate on sensor attatched to CSIA on 4460
We are using a 4460 with an OV5640 sensor attached to CSIA and are not seeing the expected frame rate. Even when I increase the speed of the MIPI clock I do not see a change in the frame rate. First,...
View ArticleClik here to view.
link token & join token, automatic change?
This is from the smpl_link example that comes with the cc2510 dev kit.As shown in the following picture, the link token and join token are set at the smpl_nwk_dat file as 12341234 and 56785678...
View ArticleA question about DM3730 video capture with gst-launch tools
Hi everyone, I use a gst-launch command to encode video, which as follow:gst-launch -v v4l2src device=/dev/video9 \! ffmpegcolorspace ! videoscale ! \video/x-raw-yuv,format=\(fourcc\)UYVY,...
View Article