Is this Forum just for engineers or also for beginners?
Hi!I have a question. Is this Forum a place where only professional engineers ask and answer or is it also dedicated to totally beginners to learn how to use TI Microcontrollers?It is very annoying to...
View ArticleWhat triggers an ILL_TRANS_DECODE ?
I am trying to connect an ML605 Xilinx FPGA dev kit (which contains a SRIO IP core) with the TMDSEVM6670LE Rev 3a. Link bring-up runs correctly, I can exchange MAINTENANCE packets, and I see no errors...
View ArticleUSB Dev. Bulk is not function on TMDXLCDK138 Eval Kit
Hi TI Engineers,With using the StarterWare 01.10.03.03 and CCS V5.1, when debug USB Dev. Bulk project, the device is detect as "Unknown Device" at Device Manager.According to StarterWare 01.10.03.03...
View ArticleFLEX-OFDM + TMDSPLCKIT-V3
I use TMDSPLCKIT-V3 on base F28069.TI presents the support of OFDM, FLEX-OFDM, FSK & SFSK for this kit.I found libraries for PRIME & G3 for this kit for frequency band 40-90 kHz (CCS builds the...
View ArticleeCAN Problem
Hi all,I am receiving/transmitting via CAN port.It is working fine until I disconnect and reconnect the CAN plug.After disconnecting/reconnecting the CAN plug, CAN is stuck and i don't know where. In...
View ArticleRebuilding Codec Engine
Hallo,I have to rebuild codec server because I must use a specific toolchain, for OMAP L138.Ifollowed the instructions described here:...
View ArticleNeed Updated TSW1200 USB Drivers for Windows 7 - 64 bit Machine
Please forgive the reposting of this question but the answers provided in an earlier thread (http://e2e.ti.com/support/data_converters/high_speed_data_converters/f/68/t/103996.aspx) appear to no...
View ArticleDM368 IPNC SDK V4.1 Doesn't build working ubifs?
I'm hoping someone can help. After getting version 4.1 of the SDK, I loaded the pre-built images into my camera, and everything worked. I was trying to install the images built from the SDK source as...
View ArticleNon-word-aligned union assignment or read results in data abort
I am using the TI ARM compiler v5.0.4, with the TMS570 microcontroller. I've encountered a compiler bug when assigning unions. Attached is a program with different tests.Assignments to unions are...
View ArticleHow can I place LOG_printf() strings in SDRAM?
My project is using CCS 5.3 to generate code for the DSP on the DA830/L-137. I use IPC v1.0.5.60, SysBios 6.21.0.13 and XDIAS 6.25.1.08. My compiler is 6.1.13. I have a lot of LOG_printf() calls. I...
View ArticleDoes CC8520 use Spread Spectrum?
Hi,Does the CC8520 use the Spread Spectrum technics?Because as I saw on Configurator, have 18 channel for use.Thanks,RF_pts
View ArticleC6678 EMIF16 boot reserved pin BOOTMODE[4]
Hi Randy,I have a customer that has a related problem on both a custom board and on the C6678 EVM.They want to boot from EMIF16. They use the expected config BOOTMODE pin config: BOOTMODE[2:0] =...
View ArticleUART Channels Other Then Default: TI-RTOS / LM4F120
Hello, I am wondering if there is anything special I need to do to setup UART1 through UART7? Essentially, I am trying to make the uartecho example work with UART1. Ultimately I need 3 channels to be...
View ArticleTo Haixiao - TMS570LS3137 MIBSPI and DMA configuration issue
Haixiao,I am using MIBSPI mode. Both MIBSPI1 (Master) and MIBSPI3 (Slave) are configured to use TG0, and try to use DMA transfer their TG0 RX data to RAM.See the attachment for the DMA and MIBSPI1 and...
View ArticleAre there any pin to pin alternate for UCC28600 controller
Hi, I am on study of this chip for flyback converter design.My concern is that does TI or any other vendor have a pin to pin substitute for this controller. will the design has to be scraped if...
View ArticleTMP006
Can i access 8 tmp006-sensors with one I2C Master. SCL and SDA acts as addresslines (Datasheet)I do not understand how this will work.
View ArticleEnabling UART using Internal Clock of MSP430F2619
Hi,I am new to MSP430 family of controllers. I am trying to bridge UART over USB link. I am using FT232RL to interface UART of MSP430F2619 to the PC.On my board I do not have space for crystal...
View ArticleIs it no problem that it does not exist pulldown resister on CKE and ODT pin...
Hello.I am gonna use DDR2 as memory of AM335x system. On datasheet Figure5-38(sprs717e P155), it specifies that the CKE pin and ODT pin are connected between AM335x and DDR2 immediately. Is it no...
View ArticleProblem with UART?
Hey!I wanted to connect to UART to see what boot messages im getting but so far i'm having issued with output. Im pretty much getting gibberish,I would assume that is due to baud rate but i set it...
View ArticleLM4F Launchpad w/ccs5.2.1 imprecise data bus error
Hello Stellaris community,I am working with a stellaris M4 launchpad ccs5.2.1. I am unable to determine why my code is tripping the imprecise data buss error sending me to faultISR. Using TI's app...
View Article