DM368 IPNC SDK V4.1 Doesn't build working ubifs?

I'm hoping someone can help. After getting version 4.1 of the SDK, I loaded the pre-built images into my camera, and everything worked. I was trying to install the images built from the SDK source as a check-point before making any changes. I found that the source did not make a working ubifs. I'm using a fresh install of Ubuntu 12.04, and after installing a few things the User's Guide didn't discuss (and posting the procedure so others could benefit), got a clean build (make sysall, make ubifsall). Transferring the images to the camera produces a kernel panic. Output is below, first from the failed built-from-source version, followed by the successful pre-built images. If anyone can help get the source as supplied in SDK V4.1 working, I'd appreciate it very much.

Serial output from images built from as-supplied source:

DM36x initialization passed!

TI UBL Base Version: 1.50

Boot Loader BootMode = NAND

Starting NAND Copy...

Valid magicnum, 0xA1ACED66, found in block 0x00000008.

Boot Mode Task Completed

IPNC UBL Version: 2.1.0

Platform: DM368-432

Jumping to entry point at 0x81080000

U-Boot 1.3.4 (Jan 29 2013 - 21:09:36) DM368-IPNC-4.1.0

I2C: ready

DRAM: 128 MB

NAND: NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit)

Bad block table not found for chip 0

loop oob 81021ad8 Bad block table written to 0x07fe0000, version 0x01

loop oob 81021ad8 Bad block table written to 0x07fc0000, version 0x01

128 MiB

In: serial

Out: serial

Err: serial

ARM Clock :- 432MHz

DDR Clock :- 340MHz

Ethernet PHY: GENERIC @ 0x01

Hit any key to stop autoboot: 0

Loading from NAND 128MiB 3,3V 8-bit, offset 0x500000

Image Name: Linux-2.6.37_IPNC_DM365_4.1.0

Image Type: ARM Linux Kernel Image (uncompressed)

Data Size: 3439968 Bytes = 3.3 MB

Load Address: 80008000

Entry Point: 80008000

## Booting kernel from Legacy Image at 80700000 ...

Image Name: Linux-2.6.37_IPNC_DM365_4.1.0

Image Type: ARM Linux Kernel Image (uncompressed)

Data Size: 3439968 Bytes = 3.3 MB

Load Address: 80008000

Entry Point: 80008000

Loading Kernel Image ... OK

Starting kernel ...

[ 0.000000] Linux version 2.6.37_IPNC_DM365_4.1.0 (a0875405@bangvideoapps01) (gcc version 4.3.3 (GCC) ) #1 PREEMPT Tue Jan 29 21:16:20 IST 2013

[ 0.000000] CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177

[ 0.000000] CPU: VIVT data cache, VIVT instruction cache

[ 0.000000] Machine: DaVinci DM36x IPNC

[ 0.000000] Memory policy: ECC disabled, Data cache writeback

[ 0.000000] DaVinci dm365_rev1.1 variant 0x0

[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 12192

[ 0.000000] Kernel command line: mem=48M console=ttyS1,115200n8 noinitrd ip=192.168.1.168:192.168.1.100:192.168.1.1:255.255.255.0:::off rw ubi.mtd=3,2048 rootfstype=ubifs root=ubi0:rootfs cmemk.phys_start=0x83000000 cmemk.phys_end=0x88000000 cmemk.phys_start_1=0x00001000 cmemk.phys_end_1=0x00008000 cmemk.pools_1=1x28672 cmemk.allowOverlap=1 cmemk.useHeapIfPoolUnavailable=1 nohz=off highres=off clocksource=acpi_pm lpj=1077248

[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)

[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

[ 0.000000] Memory: 48MB = 48MB total

[ 0.000000] Memory: 45184k/45184k available, 3968k reserved, 0K highmem

[ 0.000000] Virtual kernel memory layout:

[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)

[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)

[ 0.000000] DMA : 0xff000000 - 0xffe00000 ( 14 MB)

[ 0.000000] vmalloc : 0xc3800000 - 0xfea00000 ( 946 MB)

[ 0.000000] lowmem : 0xc0000000 - 0xc3000000 ( 48 MB)

[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)

[ 0.000000] .init : 0xc0008000 - 0xc0028000 ( 128 kB)

[ 0.000000] .text : 0xc0028000 - 0xc032c000 (3088 kB)

[ 0.000000] .data : 0xc032c000 - 0xc034fd60 ( 144 kB)

[ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1

[ 0.000000] Preemptable hierarchical RCU implementation.

[ 0.000000] RCU-based detection of stalled CPUs is disabled.

[ 0.000000] Verbose stalled-CPUs detection is disabled.

[ 0.000000] NR_IRQS:245

[ 0.000000] Console: colour dummy device 80x30

[ 0.000296] Calibrating delay loop (skipped) preset value.. 215.44 BogoMIPS (lpj=1077248)

[ 0.000355] pid_max: default: 32768 minimum: 301

[ 0.000632] Mount-cache hash table entries: 512

[ 0.001419] CPU: Testing write buffer coherency: ok

[ 0.005918] DaVinci: 8 gpio irqs

[ 0.006536] NET: Registered protocol family 16

[ 0.089638] bio: create slab <bio-0> at 0

[ 0.094558] SCSI subsystem initialized

[ 0.098357] usbcore: registered new interface driver usbfs

[ 0.099684] usbcore: registered new interface driver hub

[ 0.100915] usbcore: registered new device driver usb

[ 0.104042] vpss vpss: dm365_vpss vpss probed

[ 0.104104] vpss vpss: dm365_vpss vpss probe success

[ 0.106005] Advanced Linux Sound Architecture Driver Version 1.0.23.

[ 0.107959] Switching to clocksource timer0_1

[ 0.170467] NET: Registered protocol family 2

[ 0.170783] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

[ 0.171559] TCP established hash table entries: 2048 (order: 2, 16384 bytes)

[ 0.171698] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)

[ 0.171787] TCP: Hash tables configured (established 2048 bind 2048)

[ 0.171819] TCP reno registered

[ 0.171857] UDP hash table entries: 256 (order: 0, 4096 bytes)

[ 0.171920] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)

[ 0.172418] NET: Registered protocol family 1

[ 0.242985] msgmni has been set to 88

[ 0.245726] io scheduler noop registered (default)

[ 0.247171] CSL: Module install successful, device major num = 254

[ 0.247217] CSL: Module version 0.10.00, built on Jan 29 2013 21:10:10

[ 0.247274] I2C: Module install successful, device major num = 253

[ 0.247317] DMA: Module install successful, device major num = 252

[ 0.247345] DRV: Module install successful

[ 0.247370] DRV: Module built on Jan 29 2013 21:10:12

[ 0.247396] DRV: EDMACC.QUEPRI = 00002777

[ 0.247418] DRV: SYSTEM.MSTPRI0 = 00440011

[ 0.247440] DRV: SYSTEM.MSTPRI1 = 00000444

[ 0.247462] DRV: ISP.BCR = 00000002

[ 0.247484] DRV: SYSTEM.MISC = 00000399

[ 0.247508] EDMAK module: built on Jan 29 2013 at 21:09:58

[ 0.247539] Reference Linux version 2.6.37

[ 0.247564] File /data/datalocal_videoapps01/user/kudva/DM36x/IPNetCam_v4.0/dvsdk_ipnctools/linuxutils_2_26_02_05/packages/ti/sdo/linuxutils/edma/src/module/edmak.c

[ 0.249039] IRQK module: built on Jan 29 2013 at 21:09:55

[ 0.249090] Reference Linux version 2.6.37

[ 0.249116] File /data/datalocal_videoapps01/user/kudva/DM36x/IPNetCam_v4.0/dvsdk_ipnctools/linuxutils_2_26_02_05/packages/ti/sdo/linuxutils/irq/src/module/irqk.c

[ 0.250813] irqk initialized

[ 0.250892] CMEMK module: built on Jan 29 2013 at 21:09:57

[ 0.250932] Reference Linux version 2.6.37

[ 0.250960] File /data/datalocal_videoapps01/user/kudva/DM36x/IPNetCam_v4.0/dvsdk_ipnctools/linuxutils_2_26_02_05/packages/ti/sdo/linuxutils/cmem/src/module/cmemk.c

[ 0.255689] allocated heap buffer 0xc4000000 of size 0x5000000

[ 0.255733] heap fallback enabled - will try heap if pool buffer is not available

[ 0.255773] CMEM Range Overlaps Kernel Physical - allowing overlap

[ 0.255808] CMEM phys_start (0x1000) overlaps kernel (0x80000000 -> 0x83000000)

[ 0.255953] cmemk initialized

[ 0.256010] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled

[ 0.279902] serial8250.0: ttyS0 at MMIO 0x1c20000 (irq = 40) is a 16550A

[ 0.302095] serial8250.0: ttyS1 at MMIO 0x1d06000 (irq = 41) is a 16550A

[ 0.820383] console [ttyS1] enabled

[ 0.827182] brd: module loaded

[ 0.838804] NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung )

[ 0.847319] Bad block table not found for chip 0

[ 0.853532] Bad block table not found for chip 0

[ 0.858168] Scanning device for bad blocks

[ 0.944317] Creating 7 MTD partitions on "davinci_nand.0":

[ 0.949844] 0x000000000000-0x000000300000 : "bootloader"

[ 0.959182] 0x000000300000-0x000000500000 : "params"

[ 0.968226] 0x000000500000-0x000000900000 : "kernel"

[ 0.977388] 0x000000900000-0x000003100000 : "filesystem1"

[ 0.987146] 0x000003100000-0x000003300000 : "data1"

[ 0.996352] 0x000003300000-0x000005b00000 : "filesystem2"

[ 1.006207] 0x000005b00000-0x000008000000 : "data2"

[ 1.015610] davinci_nand davinci_nand.0: controller rev. 2.3

[ 1.024446] UBI: attaching mtd3 to ubi0

[ 1.028311] UBI: physical eraseblock size: 131072 bytes (128 KiB)

[ 1.034896] UBI: logical eraseblock size: 126976 bytes

[ 1.040469] UBI: smallest flash I/O unit: 2048

[ 1.045185] UBI: sub-page size: 512

[ 1.049806] UBI: VID header offset: 2048 (aligned 2048)

[ 1.055911] UBI: data offset: 4096

[ 1.209066] UBI error: process_eb: bad image sequence number 809040151 in PEB 192, expected 1507908790

[ 1.218856] UBI error: ubi_init: cannot attach mtd3

[ 1.270110] davinci_mdio davinci_mdio.0: davinci mdio revision 1.4

[ 1.276321] davinci_mdio davinci_mdio.0: detected phy mask fffffffd

[ 1.284042] davinci_mdio.0: probed

[ 1.287487] davinci_mdio davinci_mdio.0: phy[1]: device 0:01, driver unknown

[ 1.295349] i2c /dev entries driver

[ 1.301111] Linux media interface: v0.10

[ 1.305759] Linux video capture interface: v2.00

[ 1.312717] vpbe-osd vpbe-osd: OSD sub device probe success

[ 1.319202] vpbe-venc vpbe-venc: VENC sub device probe success

[ 1.326037] vpbe-v4l2 vpbe-v4l2: vpbe v4l2 device registered

[ 1.332217] Setting default output to Composite

[ 1.336774] Setting default mode to ntsc

[ 1.340903] vpbe-v4l2 vpbe-v4l2: Trying to register VPBE display device.

[ 1.347616] vpbe-v4l2 vpbe-v4l2: layer=c291a200,layer->video_dev=c291a2e8

[ 1.355285] vpbe-v4l2 vpbe-v4l2: Trying to register VPBE display device.

[ 1.362216] vpbe-v4l2 vpbe-v4l2: layer=c296e000,layer->video_dev=c296e0e8

[ 1.370814] watchdog watchdog: heartbeat 60 sec

[ 1.380681] Error: Driver 'davinci-mcbsp' is already registered, aborting...

[ 1.390722] asoc: cq93vc-hifi <-> davinci-vcif mapping ok

[ 1.399435] ALSA device list:

[ 1.402712] #0: DaVinci DM365 EVM

[ 1.407446] TCP cubic registered

[ 1.411031] NET: Registered protocol family 17

[ 1.424353] net eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:01, id=181b8b0)

[ 1.450866] IP-Config: Complete:

[ 1.453949] device=eth0, addr=192.168.1.168, mask=255.255.255.0, gw=192.168.1.1,

[ 1.461835] host=192.168.1.168, domain=, nis-domain=(none),

[ 1.467852] bootserver=192.168.1.100, rootserver=192.168.1.100, rootpath=

[ 1.476055] VFS: Cannot open root device "ubi0:rootfs" or unknown-block(0,0)

[ 1.483201] Please append a correct "root=" boot option; here are the available partitions:

[ 1.491662] 1f00 3072 mtdblock0 (driver?)

[ 1.496749] 1f01 2048 mtdblock1 (driver?)

[ 1.501897] 1f02 4096 mtdblock2 (driver?)

[ 1.506976] 1f03 40960 mtdblock3 (driver?)

[ 1.512112] 1f04 2048 mtdblock4 (driver?)

[ 1.517190] 1f05 40960 mtdblock5 (driver?)

[ 1.522320] 1f06 37888 mtdblock6 (driver?)

[ 1.527392] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)

[ 1.535700] Backtrace:

[ 1.538167] Function entered at [<c002c4ec>] from [<c02bffa8>]

[ 1.544050] r7:00008000 r6:c2813000 r5:c002294c r4:c03504c0

[ 1.549752] Function entered at [<c02bff90>] from [<c02c0014>]

[ 1.555632] Function entered at [<c02bffac>] from [<c0008f84>]

[ 1.561508] r3:00000000 r2:00000000 r1:c2825f78 r0:c02dc7e1

[ 1.567210] Function entered at [<c0008d20>] from [<c00090dc>]

[ 1.573086] Function entered at [<c0009048>] from [<c00084b4>]

[ 1.578927] r5:c00220e8 r4:c034fd78

[ 1.582563] Function entered at [<c00083a4>] from [<c0040e0c>]

[ 1.588400] r5:c00083a4 r4:00000000

Serial output from pre-built images:

DM36x initialization passed!

TI UBL Base Version: 1.50

Boot Loader BootMode = NAND

Starting NAND Copy...

Valid magicnum, 0xA1ACED66, found in block 0x00000008.

Boot Mode Task Completed

IPNC UBL Version: 2.1.0

Platform: DM368-432

Jumping to entry point at 0x81080000

U-Boot 1.3.4 (Jan 29 2013 - 21:09:36) DM368-IPNC-4.1.0

I2C: ready

DRAM: 128 MB

NAND: NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit)

Bad block table not found for chip 0

loop oob 81021ad8 Bad block table written to 0x07fe0000, version 0x01

loop oob 81021ad8 Bad block table written to 0x07fc0000, version 0x01

128 MiB

In: serial

Out: serial

Err: serial

ARM Clock :- 432MHz

DDR Clock :- 340MHz

Ethernet PHY: GENERIC @ 0x01

Hit any key to stop autoboot: 0

Loading from NAND 128MiB 3,3V 8-bit, offset 0x500000

Image Name: Linux-2.6.37_IPNC_DM365_4.1.0

Image Type: ARM Linux Kernel Image (uncompressed)

Data Size: 3439968 Bytes = 3.3 MB

Load Address: 80008000

Entry Point: 80008000

## Booting kernel from Legacy Image at 80700000 ...

Image Name: Linux-2.6.37_IPNC_DM365_4.1.0

Image Type: ARM Linux Kernel Image (uncompressed)

Data Size: 3439968 Bytes = 3.3 MB

Load Address: 80008000

Entry Point: 80008000

Loading Kernel Image ... OK

Starting kernel ...

[ 0.000000] Linux version 2.6.37_IPNC_DM365_4.1.0 (a0875405@bangvideoapps01) (gcc version 4.3.3 (GCC) ) #1 PREEMPT Tue Jan 29 21:16:20 IST 2013

[ 0.000000] CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177

[ 0.000000] CPU: VIVT data cache, VIVT instruction cache

[ 0.000000] Machine: DaVinci DM36x IPNC

[ 0.000000] Memory policy: ECC disabled, Data cache writeback

[ 0.000000] DaVinci dm365_rev1.1 variant 0x0

[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 12192

[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)

[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

[ 0.000000] Memory: 48MB = 48MB total

[ 0.000000] Memory: 45184k/45184k available, 3968k reserved, 0K highmem

[ 0.000000] Virtual kernel memory layout:

[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)

[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)

[ 0.000000] DMA : 0xff000000 - 0xffe00000 ( 14 MB)

[ 0.000000] vmalloc : 0xc3800000 - 0xfea00000 ( 946 MB)

[ 0.000000] lowmem : 0xc0000000 - 0xc3000000 ( 48 MB)

[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)

[ 0.000000] .init : 0xc0008000 - 0xc0028000 ( 128 kB)

[ 0.000000] .text : 0xc0028000 - 0xc032c000 (3088 kB)

[ 0.000000] .data : 0xc032c000 - 0xc034fd60 ( 144 kB)

[ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1

[ 0.000000] Preemptable hierarchical RCU implementation.

[ 0.000000] RCU-based detection of stalled CPUs is disabled.

[ 0.000000] Verbose stalled-CPUs detection is disabled.

[ 0.000000] NR_IRQS:245

[ 0.000000] Console: colour dummy device 80x30

[ 0.000296] Calibrating delay loop (skipped) preset value.. 215.44 BogoMIPS (lpj=1077248)

[ 0.000356] pid_max: default: 32768 minimum: 301

[ 0.000632] Mount-cache hash table entries: 512

[ 0.001418] CPU: Testing write buffer coherency: ok

[ 0.005916] DaVinci: 8 gpio irqs

[ 0.006535] NET: Registered protocol family 16

[ 0.089552] bio: create slab <bio-0> at 0

[ 0.094473] SCSI subsystem initialized

[ 0.098261] usbcore: registered new interface driver usbfs

[ 0.099590] usbcore: registered new interface driver hub

[ 0.100843] usbcore: registered new device driver usb

[ 0.103968] vpss vpss: dm365_vpss vpss probed

[ 0.104031] vpss vpss: dm365_vpss vpss probe success

[ 0.105928] Advanced Linux Sound Architecture Driver Version 1.0.23.

[ 0.107875] Switching to clocksource timer0_1

[ 0.170447] NET: Registered protocol family 2

[ 0.170761] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

[ 0.171529] TCP established hash table entries: 2048 (order: 2, 16384 bytes)

[ 0.171669] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)

[ 0.171759] TCP: Hash tables configured (established 2048 bind 2048)

[ 0.171790] TCP reno registered

[ 0.171827] UDP hash table entries: 256 (order: 0, 4096 bytes)

[ 0.171891] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)

[ 0.172389] NET: Registered protocol family 1

[ 0.242873] msgmni has been set to 88

[ 0.245617] io scheduler noop registered (default)

[ 0.247065] CSL: Module install successful, device major num = 254

[ 0.247112] CSL: Module version 0.10.00, built on Jan 29 2013 21:10:10

[ 0.247164] I2C: Module install successful, device major num = 253

[ 0.247208] DMA: Module install successful, device major num = 252

[ 0.247234] DRV: Module install successful

[ 0.247259] DRV: Module built on Jan 29 2013 21:10:12

[ 0.247285] DRV: EDMACC.QUEPRI = 00002777

[ 0.247307] DRV: SYSTEM.MSTPRI0 = 00440011

[ 0.247329] DRV: SYSTEM.MSTPRI1 = 00000444

[ 0.247351] DRV: ISP.BCR = 00000002

[ 0.247372] DRV: SYSTEM.MISC = 00000399

[ 0.247396] EDMAK module: built on Jan 29 2013 at 21:09:58

[ 0.247427] Reference Linux version 2.6.37

[ 0.247453] File /data/datalocal_videoapps01/user/kudva/DM36x/IPNetCam_v4.0/dvsdk_ipnctools/linuxutils_2_26_02_05/packages/ti/sdo/linuxutils/edma/src/module/edmak.c

[ 0.248926] IRQK module: built on Jan 29 2013 at 21:09:55

[ 0.248975] Reference Linux version 2.6.37

[ 0.249002] File /data/datalocal_videoapps01/user/kudva/DM36x/IPNetCam_v4.0/dvsdk_ipnctools/linuxutils_2_26_02_05/packages/ti/sdo/linuxutils/irq/src/module/irqk.c

[ 0.250673] irqk initialized

[ 0.250749] CMEMK module: built on Jan 29 2013 at 21:09:57

[ 0.250789] Reference Linux version 2.6.37

[ 0.250817] File /data/datalocal_videoapps01/user/kudva/DM36x/IPNetCam_v4.0/dvsdk_ipnctools/linuxutils_2_26_02_05/packages/ti/sdo/linuxutils/cmem/src/module/cmemk.c

[ 0.255550] allocated heap buffer 0xc4000000 of size 0x5000000

[ 0.255593] heap fallback enabled - will try heap if pool buffer is not available

[ 0.255633] CMEM Range Overlaps Kernel Physical - allowing overlap

[ 0.255668] CMEM phys_start (0x1000) overlaps kernel (0x80000000 -> 0x83000000)

[ 0.255818] cmemk initialized

[ 0.255873] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled

[ 0.279759] serial8250.0: ttyS0 at MMIO 0x1c20000 (irq = 40) is a 16550A

[ 0.301952] serial8250.0: ttyS1 at MMIO 0x1d06000 (irq = 41) is a 16550A

[ 0.820235] console [ttyS1] enabled

[ 0.827035] brd: module loaded

[ 0.838659] NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung )

[ 0.847174] Bad block table not found for chip 0

[ 0.853377] Bad block table not found for chip 0

[ 0.858010] Scanning device for bad blocks

[ 0.944157] Creating 7 MTD partitions on "davinci_nand.0":

[ 0.949687] 0x000000000000-0x000000300000 : "bootloader"

[ 0.958997] 0x000000300000-0x000000500000 : "params"

[ 0.968044] 0x000000500000-0x000000900000 : "kernel"

[ 0.977241] 0x000000900000-0x000003100000 : "filesystem1"

[ 0.987008] 0x000003100000-0x000003300000 : "data1"

[ 0.996209] 0x000003300000-0x000005b00000 : "filesystem2"

[ 1.006058] 0x000005b00000-0x000008000000 : "data2"

[ 1.015459] davinci_nand davinci_nand.0: controller rev. 2.3

[ 1.024303] UBI: attaching mtd3 to ubi0

[ 1.028168] UBI: physical eraseblock size: 131072 bytes (128 KiB)

[ 1.034750] UBI: logical eraseblock size: 126976 bytes

[ 1.040319] UBI: smallest flash I/O unit: 2048

[ 1.045035] UBI: sub-page size: 512

[ 1.049655] UBI: VID header offset: 2048 (aligned 2048)

[ 1.055763] UBI: data offset: 4096

[ 1.196968] UBI warning: process_eb: valid VID header but corrupted EC header at PEB 176

[ 1.205962] UBI warning: process_eb: valid VID header but corrupted EC header at PEB 177

[ 1.375122] UBI: max. sequence number: 7

[ 1.391608] UBI warning: print_rsvd_warning: cannot reserve enough PEBs for bad PEB handling, reserved 2, need 3

[ 1.404219] UBI: attached mtd3 to ubi0

[ 1.407989] UBI: MTD device name: "filesystem1"

[ 1.413603] UBI: MTD device size: 40 MiB

[ 1.418493] UBI: number of good PEBs: 320

[ 1.423223] UBI: number of bad PEBs: 0

[ 1.427676] UBI: number of corrupted PEBs: 0

[ 1.432180] UBI: max. allowed volumes: 128

[ 1.436804] UBI: wear-leveling threshold: 4096

[ 1.441565] UBI: number of internal volumes: 1

[ 1.446013] UBI: number of user volumes: 1

[ 1.450503] UBI: available PEBs: 0

[ 1.454952] UBI: total number of reserved PEBs: 320

[ 1.459830] UBI: number of PEBs reserved for bad PEB handling: 2

[ 1.465884] UBI: max/mean erase counter: 1/0

[ 1.470198] UBI: image sequence number: 809040151

[ 1.475036] UBI: background thread "ubi_bgt0d" started, PID 400

[ 1.540122] davinci_mdio davinci_mdio.0: davinci mdio revision 1.4

[ 1.546330] davinci_mdio davinci_mdio.0: detected phy mask fffffffd

[ 1.554042] davinci_mdio.0: probed

[ 1.557488] davinci_mdio davinci_mdio.0: phy[1]: device 0:01, driver unknown

[ 1.565356] i2c /dev entries driver

[ 1.571123] Linux media interface: v0.10

[ 1.575739] Linux video capture interface: v2.00

[ 1.582622] vpbe-osd vpbe-osd: OSD sub device probe success

[ 1.589041] vpbe-venc vpbe-venc: VENC sub device probe success

[ 1.595858] vpbe-v4l2 vpbe-v4l2: vpbe v4l2 device registered

[ 1.602036] Setting default output to Composite

[ 1.606591] Setting default mode to ntsc

[ 1.610722] vpbe-v4l2 vpbe-v4l2: Trying to register VPBE display device.

[ 1.617436] vpbe-v4l2 vpbe-v4l2: layer=c2940e00,layer->video_dev=c2940ee8

[ 1.625112] vpbe-v4l2 vpbe-v4l2: Trying to register VPBE display device.

[ 1.632048] vpbe-v4l2 vpbe-v4l2: layer=c287a600,layer->video_dev=c287a6e8

[ 1.640678] watchdog watchdog: heartbeat 60 sec

[ 1.650542] Error: Driver 'davinci-mcbsp' is already registered, aborting...

[ 1.660489] asoc: cq93vc-hifi <-> davinci-vcif mapping ok

[ 1.669197] ALSA device list:

[ 1.672475] #0: DaVinci DM365 EVM

[ 1.677246] TCP cubic registered

[ 1.680825] NET: Registered protocol family 17

[ 1.694145] net eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:01, id=181b8b0)

[ 1.720863] IP-Config: Complete:

[ 1.723943] device=eth0, addr=192.168.1.168, mask=255.255.255.0, gw=192.168.1.1,

[ 1.731829] host=192.168.1.168, domain=, nis-domain=(none),

[ 1.737843] bootserver=192.168.1.100, rootserver=192.168.1.100, rootpath=

[ 1.853635] UBIFS: mounted UBI device 0, volume 0, name "rootfs"

[ 1.859672] UBIFS: file system size: 38473728 bytes (37572 KiB, 36 MiB, 303 LEBs)

[ 1.867430] UBIFS: journal size: 5332992 bytes (5208 KiB, 5 MiB, 42 LEBs)

[ 1.874814] UBIFS: media format: w4/r0 (latest is w4/r0)

[ 1.880704] UBIFS: default compressor: lzo

[ 1.884812] UBIFS: reserved for root: 0 bytes (0 KiB)

[ 1.892663] VFS: Mounted root (ubifs filesystem) on device 0:12.

[ 1.898825] Freeing init memory: 128K

INIT: version 2.86 booting

Starting mounting local filesystems: mount Creat queue id:0

queue id:0

FileMngThread created

Creat queue id:32769

queue id:32769

AlramThread created

Share memory init success

queue id:32769

Creat queue id:65538

queue id:65538

Creat queue id:98307

queue id:98307

IPNC_DM365_4.1.0 (a0875405@bangvideoapps01) (gcc version 4.3.3 (GCC) ) #1 PREE

queue id:65538

mount: mounting /dev/root on / failed: No such file or directory

failed (1: ).

net_search_gateway:eth0, 1A8C0, 0, 1

net_search_gateway:eth0, 0, 101A8C0, 3

Check_device_version : DEVICE VER = 1 !!

CPU is DM368

*****************************************************************

IPNC BUILD VERSION: DM368 IPNC RDK V4.10.00.02

*****************************************************************

./av_server.out DM368 NTSC TI2A AEWB 1080P H264 4000000 VBR AUTO H264 512000 VBR AUTO MENUOFF &

Starting internet superserver: inetd.

ApproDrvInit: 7

Creat queue id:131076

queue id:131076

insmod: can't read '/opt/ipnc/modules/deflate.ko': No such file or directory

DM365MM Init Successful

AVSERVER UI: Initializing.

ApproDrvInit: 9

queue id:131076

ApproDrvInit: 2

queue id:131076

ApproDrvInit: 10

ApproDrvInit: 8

queue id:131076

ApproDrvInit: 6

queue id:131076

CLK Hz,

ARM Hz = 432000000

DDR Hz = 340000000

VPSS Hz = 340000000

IMCOP Hz = 340000000

[OSA_FILE ] Reading file [/mnt/nand/IMG_Paramset.bin] ... ERROR

IMAGE TUNE: Paramset File is not available..... Setting DEFAULT parameter

[ 3.690669] PHY: 0:01 - Link is Up - 100/Full

DM365MM Init SuccessfulSYSTEM.MSTPRI0 value changed to 00440011

CONFIGURING AVSERVER FOR DM368 .....

queue id:65538

SENSOR FPS VALUE = 30

[ 3.910990] mt9p031 1-0048: Detected a MT9P031 chip ID 1801

[ 3.917079] mt9p031: mt9p031 sensor driver registered !!

queue id:131076

FR : 0 users registered from exsiting face album

IPNC_DM365_4.1.0 (a0875405@bangvideoapps01) (gcc version 4.3.3 (GCC) ) #1 PREE

IPNC AUTO_IRIS = 1

Initializing...

...done initializing

Initializing...

...done initializing