LM5145: Question about LM5145 and LM5175 Synchronous operation.
Part Number:LM5145Dear support member,My customer used LM5145 and LM5175 Synchronous operation.I hava a question.I attached question file.Could you check attached file?Question Q1Could you teach MAX...
View ArticleDRV8350: DRV8350H
Part Number:DRV8350Hello,When will the DRV8350H be available for sampling and/or production?Thank you
View ArticleAWR1642: How to apply L3 memory for PROG_RAM in 1642 MSS
Part Number:AWR1642Hi, all，I want to use L3 as the PROG RAM of MSS. The address is 0x510a0000, the size is 0x20000, the address used by DSS is 0x20000000, and the size is 0xa0000. By looking at mss map...
View ArticleUCC28911: How to monitor IPK pin of UCC28911?
Part Number:UCC28911Hi,I'm still trouble shooting what causes output voltage drop shortly and turns back during the operation of my board following UCC28911 datasheet section 9.3.7 Fault Protection to...
View ArticleClik here to view.
Is there update about LMFLASHPROGRAMMER under WIN10 Enterprise Edition?
Dears:From the website LMFLASHPROGRAMMER can not been installed under Win10 Enterprise Edition. Could you kindly help give some advice?
View ArticleBQ7718: General question
Part Number:BQ7718Hi guys,For a 6S1P project I introduced the BQ40z80 at the customer. He was asking if we have a pure protection IC. Do we have a pure protection ICs without the gauging function, but...
View ArticleDAC37J84EVM: DAC37J84EVM Output issue
Part Number:DAC37J84EVMHi,I want to generate i & q signals from all 4 channels of DAC37J84EVM with Xilinx FPGA through FMC connector. I check JESD204B from FPGA side its working fine.Clk &...
View ArticleClik here to view.
UCC27524: does a -0.4V 1us pulse on OUTA pin have damage risk for UCC27524?
Part Number:UCC27524Hi UCC27524 is used to drive boost pfc mosfet.but when AC line is aserted, the inrush current will charge bulk capacitor, although the system has inrush current limit circuit, the...
View ArticleCC1352R: CC1352R HF crystal
Part Number:CC1352RHi Champs,The CC1352 datasheet mentions only the possibility to use a 48MHz quartz as XOSC_HF. But there are also several chapters and diagrams in the CC1352/CC2652 TRM mentioning...
View ArticleCC2530: How to prevent rejoining a device after coordinator reset factory?
Part Number:CC2530Hello, I use Z-Stack HA 1.2.2. I have two problem with removing a device from coordinator's table or with coordinator reset factory. When I send Hard Reset Request Command by Z-stack...
View ArticleBQ27510-G3: 4.1V charging instead of 4.2V - change parameters manually
Part Number:BQ27510-G3Hello,After doing the learning cycle at 4.2V with bq27510-g3 gauge, what are all the parameters to be modify before generate the golden image ?I suppose changeConfiguration : CC...
View ArticlePGA280: Amplifiers Forum
Part Number:PGA280While evaluating the PGA280 as the front end of an ADS1263, I am currently getting consistent errors marked by register4: 0x49. This shows me there is an issue in the input...
View ArticleCCS/LAUNCHXL-CC1350: Debug Server Scripting automated test
Part Number:LAUNCHXL-CC1350Tool/software: Code Composer StudioHi,I would like to test the software using debug server scripting. For example, I want to run the software 1000 times and see the possible...
View ArticleDS90UB960-Q1: Isolation
Part Number:DS90UB960-Q1Hi,We're planning on using a DS90UB960-Q1 in a (non critical) medical imaging application to take the FPD-Link III feeds from 4x 1920x1080 PoC cameras all running at 60fps. We...
View ArticleClik here to view.
PCM5242: PPCM5242EVM Getting Started
Part Number:PCM5242Hello,I have my PCM5242EVM module here. First test is to get simple USB Audio Passthrough to the outputs. I understand that there is a "TIDA-00385" which was a development platform...
View ArticleClik here to view.
CC2540: Btool, Ztool
Part Number:CC2540Hello,I can not use Btool and Ztool on win10.(I tried with WinXP and Win7 also. When I have to use Virtual Machine my computer is getting so slow. But any solutions would be perfect...
View ArticleCC1352P: TI 15.4 Stack with osalport: RX stops
Part Number:CC1352PHello,I am struggling with a communication failure using TI 15.4 stack since moving to the NOICALL (and osalport) variant. Here is the environment of the problem:- I am...
View ArticleCompiler/CC3220SF-LAUNCHXL: Library for File System functions
Part Number:CC3220SF-LAUNCHXLTool/software: TI C/C++ CompilerHi,I want to use a File System functions to save data when CC3220SF is disconnected form WiFi and transmit when it is connected again to...
View ArticleLinux/DRA75: TI OMAP Jacinto 6 eMMC host controller support for eMMC device v5.1
Part Number:DRA75Tool/software: LinuxHI TI Team,We have eMMC v5.1 device is connected to TI OMAP J6 eMMC Host controller, We see there is an file system (ext4 journal enable/disable) corruption issue...
View ArticleCC3100MOD: Conformal coating
Part Number:CC3100MODTo help resilience to condensation we'll be conformally coating the control board that contains this WiFi module, but it doesn't appear that such will particularly benefit the WiFi...
View Article