CC2430: How to check the flash lock protection bit status?
Part Number:CC2430Hi AllCustomer would like to add function in their code to check CC2430 flash lock protection bit status. Could you help advice which address to check the data?
View ArticleClik here to view.
CCS/TDA2: EMIF Register definitions in CCS
Part Number:TDA2Tool/software: Code Composer StudioHiIt seems that the Register Definition of the EMIF in CCS are not only incomplete (PHY_STATUS_2-19 missing), but also wrong for the existing register...
View ArticleCCS/MSP-EXP430G2: SPI or I2C example code for MSP430 to work with BME280
Part Number:MSP-EXP430G2Tool/software: Code Composer StudioHello, Now I am working with MSP430G2553 on G2 board to communicate with a BME280 pressure, temperature and humidity sensor which is from...
View ArticleADS1298: Maximum Input Voltage
Part Number:ADS1298Hi, i am not quite sure about the maximum input voltage i can measure on each channel. I need to build a votage divider that brings my measured signal (<200V) into the correct...
View ArticleClik here to view.
TPS54140: 24V to 5V DC/DC Startup issue due to bad layout?
Part Number:TPS54140Hello,We have an issue on our 2 prototypes that implements following schematic:This schematic has been validated on a previous product but today we have the following startup curves...
View ArticleClik here to view.
HD3SS3220: How to improve HD3SS3220 ESD issue
Part Number:HD3SS3220Dear Sir,My customer test ESD (8kV) fail when using HD3SS3220 externally connected Hard Disk (or SSD).The reason for the failure is that no hard disk (or SSD) can be...
View ArticleTMDSLCDK6748: C6000 Embedded Design Workshop
Part Number:TMDSLCDK6748Good morning.I was looking at the workshop on C6000 Embedded Design Workshop page and after reading a lot, I started implementing some of the Labs.However, specifically in the...
View ArticleTLV27L1: normal operation with input CMV = -0.2V for temperature range...
Part Number:TLV27L1Hello,I am looking to design in the op-amp TLV27L1 in my application where the input common mode voltage = -0.2V.TLV27L1 datasheet does state recommended minimum input common mode...
View ArticleClik here to view.
TDC1000-TDC7200EVM: Graph won't populate data from transducers
Part Number:TDC1000-TDC7200EVMI am attempting the get the TDC1000-TDC7200EVM to work with the basic level sensing application. My board is connecting properly to my PC and I can read temperature, but...
View ArticleADC12J4000: Multichip synchronization
Part Number:ADC12J4000Hi,I am trying to achieve multichip synchronization with two ADC12J4000.I am using an Arria10 with the Altera JESD IP as JESD Receiver (subclass 1).My clock configuration is ADC...
View Articlecc2538 with cc1200
Hi all, I'm trying to recreate the code for communication between a cc2538 and a cc13xx. I bought a Wepteche Gateway and am testing their software. My goal is to communicate with the IBM cloud in both...
View ArticleTMS570LS1224: Motor Control TI Designs for Hercules Electrical motor driver
Part Number:TMS570LS1224Hi Support,can you kindly list me the TI Designs we have focusing on Electrical Motor Driving based on Hercules TMS570LS12xx products?Thanks and regards,Alberto
View ArticleTPS53681: VOS Connection
Part Number:TPS53681Hello E2E,How is the VOS line to be connected to the output? Does it matter if it is connected to the output of the inductor or should it be at an output cap? Is there really any...
View ArticleAWR1243: LdoBypass mode
Part Number:AWR1243Hello，We are trying to design our own board using AWR1243. I wonder if we can provide the RF module with 1.0 volt instead of 1.3 volt with Ldobypass mode disable, will it affect the...
View ArticleCC3220MOD: act as a dynamic webserver
Part Number:CC3220MODDear Sirs,We are a manufacturer of electronic items to manage farms.We were using SPWF01 module from ST to give simple remote control to our device.This module gave us satisfaction...
View ArticleCC1350: CC1350 BLE microstack
Part Number:CC1350I've ported a CC2640R2F BLE microstack project to the CC1350, but it is not properly sending or detecting packets. I'm using code from...
View ArticleTMS320F28377D: TMS320F28377d
Part Number:TMS320F28377DSir, when I am trying to run the CLA task(CLA ISR) my cpu execution inside the while(1) is increasing .In while(1) I kept some algorithm which is taking 200 microsecs.Now if...
View ArticleClik here to view.
Calculate Inductance for the buck mode of HV9911
Hello.I'm designing LED driver with HV9911.This is the buck mode circuit,Input voltage is 250V, out maxim voltage is 200V. current is maxim 1.2AHow can I calculate the inductor and capacitor?Thank you...
View ArticleTMS320F28069M: Inertia test
Part Number:TMS320F28069MI am using the C2000 TMS320F28069MFOC card with the 8305 driver to perform an inertia test as detailed in Instaspin lab05c.It appears that the files compiled and I was able to...
View ArticleTINA/Spice: Small Voltage on Output Cap of Buck Converter
Tool/software:TINA-TI or Spice ModelsHello,I am having issues trying to simulate a start up of 12 -> 3.3 V buck. The output voltage measured is usually very small when I run DC nodal analysis,...
View Article