Event when BLE notification has been enabled/disabled
Hi :)How do I get an event when a BLE notification has been enabled or disabled by the central? I guess the configuration and I will be able to read that. But an event on configuration changes would be...
View ArticleInterfacing ADC (>60MSPS) to OMAP138
Hi,I am trying to design a board that will interface a high speed ADC to OMAP138The ADC should be 10b @(>60MSPS), pereferably low power.I would like to design it without glue logic if possible and...
View ArticleLooking for help building syslink
Hi,Looking for some help building syslink.NOTE: All the individual files I mention below are part of attached logs.tar.gz (can be extracted using tar xvzf logs.tar.gz on a linux machine)I am trying to...
View ArticleInterfacing to WaveVision
I would like to design a board similar to the ADC10080 EVM that will contain some added circuitry and will interface to the WaveVision (like the ADC10080 EVM ).What is the function of the EEPROM on the...
View ArticleDM8148: HDMIPLL_FRACDIV register's FRACTIONALM field format
Hi.I have a question about HDMIPLL_FRACDIV register's FRACTIONALM field format on DM8148.For example, Fractional M is 0.5In the case, FRACTIONALM field should set 0x00005 ? otherwise, FRACTIONALM...
View ArticleTrouble with debugging StellarisWare samples
Hello, I am trying to debug latest StellarisWare samples (version 3740) for intelligent display module board with eval version of IAR 5.20. I am using j-link jtag debugger. When running samples from...
View ArticlePWM instead of Crystal on CC2500
The CC2500 data sheet has the following text Refer 26.1 The chip can alternatively be operated with areference signal from 26 to 27 MHz instead ofa crystal. This input clock can either be a...
View ArticleVariables Defined in Functions Not Working
Hello,I am kicking the dust off of a few old projects as I get back into MSP430 programming. I noticed that the function below did not work when the variable "count" was defined in the function. If I...
View ArticleClik here to view.
cc2510 PCB antenna
Hi, questions regarding the cc2510 PCB antenna, as shown on the picture above taken from the TI design note, the two ends seem to be in the "ground layer 2", but then there is "via to ground" on one...
View ArticleClik here to view.
3port 0 resistance resistor
The above picture was taken from the cc2510 mini-development schematic document, what is the purpose of connecting this R2 resistor with ZERO resistance to the PCB antenna? Because it is of ZERO...
View ArticlePlease help me get DM368 IPNC SDK 4.0.0 up and running
Sorry to cross-post but there's nothing but tumbleweed in the DM36x forum and I'd quite like to get some stuff working... I'm looking for some basic assistance / explanation of how to get up &...
View ArticleDual Video recorder
I am looking for the best DSP suitable for a new development. Since I didn't developed with Da Vinci before I prefer to get a recommendation.I need to design a dual channel Video recorder from...
View ArticleBQ500410A Boot Fail Issue
Dear TI Team.My customer developed A6 Type charging pad using BQ500410A. However, 30 of 250 sets didn't work properly - No charge, LED display error, and so on...I found the defect of INA199A1. The...
View ArticleDM8148: McASP.5 edma event mapping fails and crashes in...
Hi,I've added a sound device for our VCAM board.root@dm814x-evm:~# aplay -l**** List of PLAYBACK Hardware Devices ****card 0: VCAM [TI81XX VCAM], device 0: AIC3X tlv320aic3x-hifi-0 [] Subdevices: 0/1...
View ArticleMSP430F2012 PWM with momentary switch and interrupt function
Hello all,I am new to the msp430, and am struggling with a current program. I can output a 5ms x 10ms on P1.2 as desired, would like to use an interrupt function to output a specific X number cycles...
View ArticleMSP430F1611 UART Problem - 115200bps - SMCLK 1MHz
Hi all, I'm trying to develop a small program that sends every second 1 byte on the uart using the MSP430F1611.The MCU is working at 4096 binary kHz, and I want to use a baudrate of 115200bps for the...
View ArticleHow to treat these dedicated input Pins(VPP,EXTINTn,EXT_WAKEUP) on AM3352?
1,VPP,Supply voltage range for the FUSE ROM domain. I found "During functional operation,this pin is a no connect" on page 78 in "SPRS717D–OCTOBER 2011–REVISED MAY 2012". But in "AM335X 15X15 ICE...
View ArticleGUI Composer not showing in CCS 5
Hello,I could not find GUI Composer in my installed CCS 5 (in the view tab).I downloaded the GUI Composer separately, but the application would not run in edit mode.Can you help please.regardsSM
View ArticleBootloader never show BOOTME message
HiI followed the steps mentioned in TMS320DM6467 DVEVM v1.40 getting started guide asFlashing UBL to SPI EEPROMand then Flashing U-boot to NANDand flash writer completely writes u-boot to NAND but my...
View Article