How to Use 6678 eth0 and eth1 with different MAC simultaneously
Hi AllI have a customized board with 6678 processor.Need to use Core 0 with eth port 0 with unique Mac and Core 1 with eth port 1 with its unique MAC Simultaneously( eth0 and eth1 with same MAC -mirror...
View ArticleSlave I2C secondary boot
We are designing a board with multiple C6678 devices and an ARM controller. We would like to boot the C6678s using secondaryboot over Ethernet after configuring the boot parameter table using I2C from...
View ArticleHow to Debug the Program for Two Boards
Hi~We are working on two boards to let them communicate under the LTE standard. We use software defined radio to implement the LTE standard. We have two emulators for the two boards and also the...
View Articlexds100v1 and custom board
Hi to all, I made my own board using the tms320f28027 (following the controlstick squematics). I'm using the Code Composer Studio version 3.3.81.28. I followed the instructions that came...
View ArticleValidation of Software
My company produces medical devices and are required by the FDA to validate our software. One of our products uses a battery that is evaluated and calibrated by the bq2060AEVM-001 and bq2060AEVM-002...
View ArticleCCS V5 Error
Compiles C++ program and builds with no errors. Debug loads with no errors. But not all program is loaded into MSP430F233 chip.
View ArticleTPA3130D2 SDZ & MUTE
Dear, Sir. We are promoting TPA3130D2 for a audio system, analog input and Mono 4ohm/20W output.The customer faced pop noise problem before, hence serious for mute function.TPA3130D2 has 2 pins, SDZ...
View ArticlePackage thermal characteristics for SN65LVDT14 in a 20 pin PW TSSOP
Hello,Are the package thermal characteristics (theta JC,JA,JB.....) available for the SN65LVDT14 in a 20 pin TSSOP?Thanks for any help.
View ArticleLM 5022 based SEPIC converter
I worked on WEBENCH for a power supply that requires a SEPIC converter (Input voltage range is 10V to 18V & output required is 12V@ 3.0Amp). TI shows an application note for this requirement but...
View ArticleProgramming InstaSpin BLDC GUI project to custom F28035 + DRV8332 board
We are trying to use the Instaspin library on a custom board that is almost a carbon copy of the F28035 control card and the DRV8312 schematics. We are programming through the XDS USB100v2 JTAG...
View ArticleMaximum junction temperature for SN65LVDT14
Hello,Is the maximum junction temperature for the SN65LVDT14 available?Thanks for any help.
View ArticlePin assignments AM3359 in Excel form
Hello,I'm designing a PCB with the AM3359ZCZ. I want to create a very comprehensive schematic symbol for the AM3359ZCZ that shows the signal names available for each mode (mux setting), not just the...
View ArticleClik here to view.
CC1101+CC1190EMK RF output issue
HI,This is urgent…..!Actually I am having CC1101+CC1190EMK(for 869MHz) of the customer and facing the issue not able to set the RF Frequency properly.With Frequency settings from RF studio(connected to...
View ArticleSpare Parts
HI,We have bought several Pico 2 in the past years using distributor and now we collected few broken of them .all they have the Main Board PN 0019581G001 rev A faulty.We recognized it swapping boards...
View ArticleClik here to view.
Current flowing out of INA226 VIN- terminal when shunt voltage well exceeds...
Hello, For clarifying the issue, I used INA226EVM to recreate the case. VIN- is connected to GND through 6.8k resistor. VIN+ is connected to VS(3.32V). See the attached pics for detail setup. The...
View ArticleClik here to view.
Weird ADC Problem
Hello,I am experiencing a weird issue with my ADC where every 8 or so samples, it "doubles up" on a sample, meaning that it skips the value that it should be at (assuming a sinusoid) and it instead...
View ArticleControlCard F28069 Piccolo to sample 4 analog signal with ADC
I am using a peripheral explorer with ControlCard F28069 Piccolo. I am trying to configure the ADC to sequentially sample 4 different signals. I was able to get two working and I am having issue with...
View ArticleClearing the emac rx interrupt with the RXnCP completion pointers.
I have a TMS570 connected to a non-TI PHY controller, a Micrel KS8721. I have lwip working on the TMS eval board that has the TI dp83640 phy, and I can step through the rx handler and see it clears...
View ArticleAnother RF BSL for the Chronos?
TI Chronos Wiki says there is a RF BSL project in development. I am thinking of writing Another RF BSL for the Chronos on my own.Anybody interested in joining me to do that and put it in public...
View ArticleWhat is the distinction between OUTMOD0 and OUTMOD_0?
In the MSP430G2553.h there are these definitions for the timer:#define OUTMOD2 (0x0080) /* Output mode 2 */#define OUTMOD1 (0x0040) /* Output mode 1 */#define...
View Article