Stellaris Launchpad LM4F120XL vs Kentec -L35 display example
I using the workbook examples and labs from the website with the specified hardware. Stellaris Lauchpad LM4F120 & KentecEB-LM4F120-L35CCS Version: 5.2.1.00018, Stellarisware from...
View ArticleWhich of the several Bluetooth LE modules should I consider to use with the...
Hello to all,My request is for some comments and suggestions about “which of the Bluetooth modules” and “the assocaited development system” should I be using to develop the Bluetooth communications...
View ArticleCan VeRef+ be higher than Vcc?
Can the external positive voltage reference for the G series ADC10's be higher than the chips Vcc value? For example could I monitor a 4 volt or 5 volt signal with the ADC10 of an MSP430G chip using...
View ArticleQuestion about MSP430 and Bluetooth
Hi,I am looking for a low power development board of Bluetooth and microcontroller. This board need to work of few weeks by coin battery or rechargeable Lithium.My target is to have the ability to...
View ArticleeZ430-Chronos-868 - eZ430-Chronos Wireless Watch Development Tool
Hello . I am from India .I would like to know how i should order eZ430 chronos 868 watch ? What is its cost because the TI-authorized Indian distributor's site shows it as 100$ while the TI-estore...
View ArticleESM Group 3 error
I have an application that uses the TMS570LS3137 processor. The HET 1 module is used to produce several PWMs The HET2 module also produces a PWM at a different frequency. The ADCs are triggered by RTI...
View ArticleHelp getting started with the DRV8301-LS12-KIT Motor Dev Kit (TMS570LS1227...
Hi,I just got a DRV8301_LS12_KIT with the Hercules TMS570LS1227 processor. I want to just spin the motor first. InstaSPIN demo sounded great, but is not living up to the name for me. The written...
View ArticleMicrostrip width sanity check
Hello all, I am trying to layout a microstrip line on a 2 layer FR4 board for CC1101. The ISM frequency that I will be using is 915MHzAccording to several (online) calculations, the strip width...
View ArticleDRV8312 getting hot
Please excuse what is probably a complete newbie question but I'm having another problem with my DRV8312-69M-KIT. I'm trying to run the BDLC_Sensorless project with a small outrunner motor. I'm at...
View ArticleHow to use RTC based on I2C with LM3S6911
HiI am using RTC IC FM31/256 which is connected at I2C0 on portB of my LM3s6911 board. I have enabled the RTC oscillator , then make Read reg 1 to enable read and then make it 0 to transfer RTC. Then I...
View ArticleTrying to cross compile the kernel Module for beagle bone A3 :
Source Code : Linux : linux-3.1.0-psp04.06.00.03.sdk U-boot : u-boot-2011.09-psp04.06.00.03 Toolchain : [linux-devkit]:/home/linux/Practise/application_linux> arm-arago-linux-gnueabi-...
View ArticleProblem loading my program on stellaris launchpad flash
Hi,I'm evaluating stellaris microcontrollers using a stellaris launchpad. I've debugged the examples for my board included in StellarisWare with out any problem. I've created a new project, copied the...
View ArticleConstant Current Source of about 300mA with variable frequency ranging from...
I want to make a constant current source for my project of "Designing of Eddy Current Testing Probe" at my research lab. This constant current source will excite the the coil of Eddy Current Probe and...
View ArticleLooking for a recommendation for a single supply op amp for a audio preamplifier
Looking for a recommendation for a single supply op amp for an audio preamplifier. Most seem to be dual supply voltage.
View ArticleRe:Bootloader for LM4F232 kit
Hi,I am using LM4F232 evk and LM Flash programmer.I tried the steps given in the below links to set up the serial bootloader to work but was not successful, getting error when tried to load code via...
View ArticleUse DSP to convert YUY2 to RGB
I have a DM8148 with software EZSDK 5_05_02_00. As the project requirement, we need to capture video from web camera and display it on screen without gstreamer. The camera provides YUY2 format and the...
View ArticleTL16C752BPTR ESD spec
Hi team,Can you please let me know the specification of ESD (air & contact both) ?1. application : AVN automotive2. customer : HD mobis3. MP : is now MP statusThanks in advnace.
View ArticleCCSv5.4 how to move/copy a Terminal from one Perspective to another?
It is very awesome to have the Terminal feature in CCS. So when I recently installed CCSv5.4.0.00091, the first thing I did was open a couple of Terminal Windows on /dev/ttyUSB0 and /dev/ttyUSB1....
View ArticleDRV2603 Issues
I have recently obtained a DRV2603 EVM-CT and have been trying to modify the firmware via CCS.It seems like I cannot get the device to register on my computer using an MSP430 eZ430-F2013 development...
View Articlei can't build a new ccs project at v5.4
Hi,I'm new at code composer studio. my problem is when i click 'file>new>' i see only c++/c project, cant see the css project. And there is no css project option. where do i fail? Did i install...
View Article