DM368 DDR2 access problem
Hi,I have a few question about DM368 DDR2.We are having a CPU exception problem caused by DDR2 write/read accesswhile doing audio encode process.When reading 32bytes data from DDR2, the first 4byte...
View ArticleNDK server ack delay on first packet
Hi, So I am running the NDK stack and I have a server task running. It seems that when the PC tries to send me a 64k byte chunk of data, the first packet gets re-transmitted multiple times before I...
View ArticleLM22670,LM22677...
Hello Mr/Ms, I will use LM22670-adj in topology Buck and inverter together with LM22677 in buck topology (3x CI LM22670 as buck, two CI LM22670 inverter, and one LM22677 as buck). I want to use the pin...
View ArticleDAC Working-Code Examples for MSP430F6638IPZ
I am working on MSP430F6638IPZ Chip. This chip is mounted on a board and this board can be connected to the CPU by MSP430 USB-Debug-Interface MSP-FET430UIF. Can anyone provide some basic code examples...
View ArticleMSP430G2553 peripheral API
Is there any peripheral API for MSP430G2553? If so I need the documentation. Please answere asap
View ArticleHow to configure the LCD timing?
Hello,everyone:I'm using BB-XM rev c(DM3730), now i bought a LCD the timing is below:Item Symbol Min. Typ. Max. Unit Frequency...
View Articleread/write nor flash memory...?
Hi,I want to read and write the nor flash but not as MTD(char or block) partition.For ex:I have my data 'A' I want it to write to some memory address for ex:0x0700001(address of nor flash). and read it...
View ArticleClik here to view.
DM368: vertical black lines on the video output
I've succeed in recording analogical video (Component ) in 720p60, 1080p30 and 1080i60.The video files created ( only H264ES frame ) are displayed with Linux Player without any error: the picture is...
View ArticleSecurity Accelerator questions on configuration
Hi Ti Folks, Please correct my understanding related to SA channels and security contexts. lets say i am using snow 3g Cipher/decipher and assume i have 3 Users U1, U2 and U3.1....
View Articleshared Uart between two cores of C6657
hi sirs,I am trying to run different *.out file on core0 and core1 of C6657 via RBL pcie boot. And then Core 0 send "Core 0 boot form PCIe..." when it is running via Uart. And Core 1 send "Core 1 boot...
View ArticleADC SOC sequence
Hi,i have a short question about the conversion seqeunce on a trigger. I am able to configurate the ADC to start conversion of several channels from a single SOC trigger. If i do so will the conversion...
View ArticleCAN SINGLE ANTENNA USE FOR (BT+RFID)?
Hi all good morning., I want just be a clarification whether i can i use single antenna(2.4ghz) for both BT & RFID?
View ArticleUA78M05 Test
Hi,I was looking for an small LDO for our application,Vin=24V,Vout=5V,I<100mASo I found UA78M05CKVURG3. I am now testing it without any caps.1. I use normal resistors 50 ohm as the load. The output...
View Articleti sdk 2.6.37 kernel - "omap3evm Camera Module" build ERROR
Hi community, I am working with an gumstix overo board and I got the "ti-dvsdk_dm3730-evm_04_03_00_06" from Texas Instruments. I want to use a camera from e-Con-Systems and I found out that the kernel...
View ArticleOMAP-L138 DSP+ARM9 LCDK Linking GPIO functions
I have installed the SYS/BIOS dev kit with CCS 5.3.0 and compiled one of the Minimal programs for the ARM9 LCDKOMAPL138.It compiled without error.I then added to main.c the following...
View ArticleClik here to view.
SERDESUB-21USB I2C communication in Display mode
Hi,I am currently evaluating the SERDESUB-21USB kit and I am experiencing problems with the I2C interface when operating the SERDES chip set in the Display mode, and I was hoping somebody could point...
View ArticleCC2420 ACT AS RFID ACTIVE TAG
Hi all, CC2420 is a 2.4GHZ IEEE 802.15.4 RF TRANSCEIVER , It contain external antenna right My query is After connecting the Antenna(2.4GHZ) for this...
View ArticleMSP430F5437A DIE revision changed UART A1 behavior
We've been building with REV E of the MSP430F5437A for almost 2 years. This month we had an entire batch of devices fail during manufacturing tests and at this point it appears the problem exists with...
View ArticleBQ76PL536A: change address to BQ
Hi!I want to know if it is possible to give a BQ any valid address; or if it has to be necessary first BQ on stack address1; second BQ on stack address 2...etc.I have two BQs configured as HOST in 2...
View ArticlePatch v 1.10.2, UDP doesn't work
Hi!After patching TIWI-SL to 1.10.2 version my UDP application stops working.Patching was done automatically through MSP Flasher. SP vershion is 1.14 after patching.I have pretty same projects on my...
View Article