Gerber file of TLC59116EVM-390
Hi All,We are interesting in TLC59116EVM-390, so can we have gerber file of TLC59116EVM-390?Thanks,NT
View ArticlePrintf,Scanf is not working
HI, I am using CCS5.3.0009. I am using F28M36x device. In the blinky project i put some printf and scanf. But both are not working.Please tell what i need to change to print the statement.Thanks in...
View ArticleCC2530 - Configuring Port0 as II/O
Hey guys,I'm trying to configure PORT0 as output general purpose pin. My main goal is to write a logic one to a pin and test with a scope that it actually changes.I'm using the following code at the...
View Article昇圧/降圧 電源の必要な 入力電流 可能な 出力電流 について
昇圧/降圧電源の何れにおいても、必要な入力電流、可能な最大出力電流は「電流 x 電圧」の入出力電力を基本にして考えます。 ・ 必要入力電流＝最大出力電流 x 出力電圧/入力電圧 この式にコイルのリップル電流の変動分と損失分を加えます。...
View ArticleCC2541 Keyfob removed?
Hello,I had previously looked into the mini dev kit which included the CC2541 on the keyfob instead of the CC2540. It seems this product has been removed and I can no longer find it anywhere to...
View ArticleUART Configuration trouble
Hi All, First post, be merciful. I have CC2540-MINI keyfob setup, IAR 8.20 with 1.3 BLE Stack . My goal is to setup a simple UART communication link. I studied DN112 to familiarize myself with UART...
View ArticleZNP Application on CC2530 gets stuck
Hello,We have some devices comprised of a MSP430F5528 (ZAP) and a CC2530 running the 2.5.1 ZNP application. The interface between the two is SPI. We've been noticing that, after an undefined amount of...
View ArticleTMS320C6678でSGMIIを2ポート同時に使う方法
こんにちは TMS320C6678を搭載するカスタムボードでSGMIIを2ポート同時に使うことを考えております。この場合のカスタマイズポイントを教えて頂けないでしょうか？ 下記のソフトウェアを調べたところ、1ポートのみ使う設定のように見受けられました。2ポートを同時に使う場合のサンプルコードがあれば教えて頂けないでしょうか？・TMDS320C6678 Platform Development...
View ArticleDRV8412/8432: how to control rotation direction and rotation speed?
Hi all,I'm a little confused by datasheet and some example code.for motor control, I want to know,1. under mode 1 (or mode 2), does one pwm control left bridge while the other pwm control right bridge?...
View ArticleThe VPss is locked up when "Overlow" detected。how can it be avoided？
I`m using a DM8168 board with DVR_RDK3.0 and encounter a big problem： VPSSM3 sometimes gets locked up When I disconnect or reconnect the video input cable. The debug message is as follows:...
View Articlex-loader compilation
Hi Everyone, I'm using DevKit8000, I want to compile x-loader but it is not compiling I have followed the procedure everything which is explained below,make distcleanmake ARCH=arm...
View ArticleDRV8432
Hi,I'm looking for an appropriate heat sink for a DRV8432 chip. I will most likely be running this at 4A continuously, but I would like the option of going up to 10A. The eval module has a heat sink...
View ArticleHow can i used uart2 on profile 0 of AM335x EVM ?
Dear all,I'm using custom board with AM3352.I need to only 3 uarts without cpld and lcd. (used profile 0)Just like baseboard type of AM335x GP EVM.I modified some code...
View ArticleCan I use C-Spy Debugger on CC2531 Dongle without SmartRF05 EB connected to...
I have set up the CC2531USB Dongle as a coordinator using the GenericApp CoordinatorUSB Sample. I'm not sure if I phrased this question properly but:Can I use C-Spy Debugger on CC2531 Dongle without...
View ArticleClik here to view.
PPS topology functionality
Attached is a view of my default PPS. I build and download code, copy and save the main_Rate44.cfg file and modify it for appropriate clock rates etc and resave it as a .txt file. I then load it as a...
View ArticleClik here to view.
ADS1248 conversion always reads 0x7FFFFF
Driving ADS1248 EVM board with SPI from Microchip dsPICDEM 2 board hosting dsPIC30F4013. Three SPI wires: clock, data-out, data-in. Programmable discretes are chip select out, and DRDY in. Not using...
View ArticleSetup time for nRESET fro a DRV8825
What are the timing constraints for the nRESET pin of the DRV8825 motor driver?Datasheet mentions a "T_enbl" of 650ns for the nENBL. What is that for the reset pin?What is the minimum width for the...
View ArticleC6455 Disqualified loop: Software pipelining disabled
Hi When I compile the DSP_fft16x32_sa.sa in my project, there is "Disqualified loop: Software pipelining disabled " in debug list. How can I solve it ? [DSP_fft16x32_sa.sa]...
View ArticleHow can I get RI-ACC-PBOX-20 ?
I need RI-ACC-PBOX-20 to program TMS37122/TMS37127 . But how to buy it in China.
View ArticleDM6437 use imgenc, and how to set proper params of imgenc_control(),...
recently, I used EVMDM6437, and I want to encode data from camera to jpeg, but I can not set proper params of imgenc_control(), imgenc_process(). The index.html has not description in detail. So where...
View Article