Part Number:TPS22810

Hi

The our customer is consider about CT capacitor.

How much capacitor is it possible? I would like to know the maximum value(limit).

Regards,

Koji Hamamoto

Part Number:AM5728

Tool/software:TI-RTOS

I am developing PRU-ICSS and TI-RTOS applications,but now I have a problem about data communication between PRU and TI-RTOS.I don't know how to achieve it. 

I readed the code and documents in pdk_am57xx_1_0_7/packages/ti/drv/pruss/test and pdk_am57xx_1_0_7/packages/ti/drv/pruss/example, and knew the transmission and reception of events but I am still in doubt about big data communication between PRU and RTOS.

So have there any clear tutorials or samples about big data communication between PRU and TI-RTOS?

Please help me.

Thank you.

Part Number:TMS570LS0232

Tool/software: Code Composer Studio

Hello, TI Engineers

The following figure is my settings about producing HEX file.

What should I set for loading the HEX file into the board by Uniflash? And How to configure memory width and rom width?

Thanks!

Regards!

Xinyu

Part Number:TLC59116

Our customer are evaluating TLC59116 at the following conditions.

[Conditions]

VLED=4.3V(TBD)

VCC=5.0V

ILED=30mA(max)

VF=4.0V(max)

They would like to know use “Output voltage = 0.3V” because they have to decrease the heat of LED block.

According to Figure2 of datasheet, we guess that TLC59116 can sink the LED current 25mA at the output voltage is 0.3V and 30mA at the output voltage is 0.5V.

(Unfortunately, it is higher than the output voltage that they expect.)

Is my understanding correct?

If no, could you please let us know the minimum voltage that TLC59116 can sink 30mA?

Regards,

Kanemaru

Part Number:MSP430FR2433

Hi TI Experts,

Please let me confirm the following question.
[Question]
Can customer use the I2C module in MSP430 device when the supply voltage is 1.8V?

I know that they need to supply the 2.0V in order to release the reset. So after power-up, they will change the voltage from 2.0V to 1.8 V and disabled the SVS function to avoid the reset.
If you have any questions, please let me know.
Best regards.
Kaka

Part Number:BQ51025

Dears,

    My customer use BQ500215 as emitter ,BQ51025 as receiver, but there are odd problem, the normal power is 10W, but some equitment  the power drop down to 2-4W after running 2-4hours. when restarting it ,it can not recover. the customer sch as follow, Could you give me hands on this issue?

Part Number:CC1101

Hello

I have run into a problem with the packet length of the CC1101. I am using a variable packet length, thus am I making use of the optional length byte. I want to transfer a file of approximately 300KB from the one CC1101 (DeviceA) to the other CC1101 (DeviceB). I am breaking this file into smaller chunks when sending it to the other DeviceB, this device must send ACK if the received packet if CRC is fine otherwise it must NAK to DeviceA. DeviceA must receive this ACK/NAK and the send new chunk or resend the failed chunk. When DeviceB sends the ACK/NAK message the message corrupts when recieved on DeviceA, but when a add another CC1101 (DeviceC) that only have to receive the ACK/NAK messages send by DeviceB the messages does not corrupt. 

When debugging on DeviceB I can see that the optional length byte of the packets are not the expected, the value of the optional length byte is my first byte of the payload. Even if I read out of the RXBYTES register the value is not the expected length, but the value is consistent if I read it multiple times. it feels like I an issue between switching between TX and RX. Can someone help me with this issue?

Part Number:TMS320f28379d

Tool/software: Code Composer Studio

Hi

i worked with example programes in C:\ti\C2000Ware_1_00_00_00_Software\device_support\f2837xd\examples\cpu1.

but now i want do a new project by using this doc:F2837xD Firmware Development Package-USER’S GUIDE...page No;18 to 25. CPU 1 Subsystem Project Creation

but i  got this error...please help me to do...

Description Resource Path Location Type:   #1965 cannot open source file "F2837xD_device.h" F2837xD_Adc.c         /sine_PWM line 46 C/C++ Problem

i think some linker problem...

 i followed the same ....

Our customer requests us to implement beamforming with four microphones. As far as I know this technology is implemented by a specific Algorithm on DSP of host processor or additional audio signal processor. Does TI have any codec to implement the beamforming and Echo and noise cancellation? 

Part Number:ADS127L01EVM

Hello TI,

We have ordered new ADS127L01EVM and installed following in a Windows 10 PC.

1)ADS127L01EVM-DVCPKG : ADS127L01EVM Device Package

2)ADS127L01EVM-DVCPKG: ADS127L01EVM Device Package

I still see issue with Generic Bulk device as in picture , release notes mention that windows 10 driver issue is resolved.

Has someone faced similar issue with latest software as well? 

Can someone at TI support with this issue

Best Regards,

Ashok

Part Number:TM4C1294NCPDT

Tool/software:TI-RTOS

Hi all , 

   I follow this page "http://processors.wiki.ti.com/index.php/Using_wolfSSL_with_TI-RTOS#WolfSSL"  to run github exmaple code (tcpEcho_Server_TivaTM4C1294NCPDT) but fail . 

   The wolfssl libary was build successfully . but it seems not work while example code refer to wolfssl libary . 

**** Build of configuration Debug for project tcpEcho_Server_TivaTM4C1294NCPDT ****

"C:\\ti\\ccsv7\\utils\\bin\\gmake" -k all
gmake[1]: Entering directory 'C:/Users/Brenden/workspace_v7/tcpEcho_Server_TivaTM4C1294NCPDT/Debug'
'Building file: ../tcpEcho.cfg'
'Invoking: XDCtools'
"C:/ti/xdctools_3_32_00_06_core/xs" --xdcpath="C:/wolfssl/tirtos/packages;/packages;/packages/ti/ndk/inc;C:/ti/tirtos_tivac_2_16_00_08/products/bios_6_40_02_27/packages;C:/ti/tirtos_tivac_2_16_00_08/products/ndk_2_23_01_01/packages;C:/ti/tirtos_tivac_2_16_00_08/products/uia_2_00_01_34/packages;C:/ti/tirtos_tivac_2_16_00_08/packages;C:/ti/tirtos_tivac_2_16_00_08/products/tidrivers_tivac_2_16_00_08/packages;C:/ti/tirtos_tivac_2_16_00_08/products/bios_6_45_01_29/packages;C:/ti/tirtos_tivac_2_16_00_08/products/ndk_2_25_00_09/packages;C:/ti/tirtos_tivac_2_16_00_08/products/uia_2_00_05_50/packages;C:/ti/tirtos_tivac_2_16_00_08/products/ns_1_11_00_10/packages;C:/ti/ccsv7/ccs_base;" xdc.tools.configuro -o configPkg -t ti.targets.arm.elf.M4F -p ti.platforms.tiva:TM4C1294NCPDT -r release -c "C:/ti/ccsv7/tools/compiler/ti-cgt-arm_16.9.0.LTS" "../tcpEcho.cfg"
making package.mak (because of package.bld) ...
generating interfaces for package configPkg (because package/package.xdc.inc is older than package.xdc) ...
configuring tcpEcho.xem4f from package/cfg/tcpEcho_pem4f.cfg ...
Error: Could not find wolfSSL library! Make sure the wolfSSL library is built and package path is updated for the build tool to find the library. More detailed wolfSSL build instructions can be found in the TI-RTOS user guide.
generating custom ti.sysbios library makefile ...
Starting build of library sources ...
making C:/Users/Brenden/workspace_v7/tcpEcho_Server_TivaTM4C1294NCPDT/src/sysbios/sysbios.aem4f ...
gmake[1]: Entering directory `C:/Users/Brenden/workspace_v7/tcpEcho_Server_TivaTM4C1294NCPDT/src/sysbios'
gmake[1]: Nothing to be done for `all'.
gmake[1]: Leaving directory `C:/Users/Brenden/workspace_v7/tcpEcho_Server_TivaTM4C1294NCPDT/src/sysbios'
Build of libraries done.
clem4f package/cfg/tcpEcho_pem4f.c ...
warning: ti.tirtos.TIRTOS: "C:/ti/tirtos_tivac_2_16_00_08/packages/ti/tirtos/TIRTOS.xs", line 49: ti.tirtos.TIRTOS : ti.tirtos.TIRTOS module is no longer required to configure driver instrumentation. Please use the ti.drivers.Config and ti.mw.Config modules instead.
'Finished building: ../tcpEcho.cfg'
' '
gmake[1]: Leaving directory 'C:/Users/Brenden/workspace_v7/tcpEcho_Server_TivaTM4C1294NCPDT/Debug'
'Building file: ../EK_TM4C1294XL.c'
'Invoking: ARM Compiler'
"C:/ti/ccsv7/tools/compiler/ti-cgt-arm_16.9.0.LTS/bin/armcl" -mv7M4 --code_state=16 --float_support=FPv4SPD16 --abi=eabi -me --include_path="C:/ti/wolfssl-3.12.0" --include_path="/packages/ti/ndk/inc" --include_path="/packages/ti/ndk/inc/bsd" --include_path="C:/ti/ccsv7/tools/compiler/ti-cgt-arm_16.9.0.LTS/include" --include_path="C:/ti/tirtos_tivac_2_16_00_08/products/TivaWare_C_Series-2.1.0.12573c" -g --gcc --define=PART_TM4C1294NCPDT --define=TIRTOS --define=ccs --define=TIVAWARE --define=_INCLUDE_NIMU_CODE --define=ccs="ccs" --display_error_number --diag_wrap=off --diag_warning=225 --gen_func_subsections=on --preproc_with_compile --preproc_dependency="EK_TM4C1294XL.d_raw" --cmd_file="configPkg/compiler.opt" "../EK_TM4C1294XL.c"

>> Compilation failure
subdir_rules.mk:9: recipe for target 'EK_TM4C1294XL.obj' failed
"../EK_TM4C1294XL.c", line 65: fatal error #1965: cannot open source file "inc/hw_memmap.h"
1 catastrophic error detected in the compilation of "../EK_TM4C1294XL.c".
Compilation terminated.
gmake: *** [EK_TM4C1294XL.obj] Error 1
'Building file: ../tcpEcho.c'
'Invoking: ARM Compiler'
"C:/ti/ccsv7/tools/compiler/ti-cgt-arm_16.9.0.LTS/bin/armcl" -mv7M4 --code_state=16 --float_support=FPv4SPD16 --abi=eabi -me --include_path="C:/ti/wolfssl-3.12.0" --include_path="/packages/ti/ndk/inc" --include_path="/packages/ti/ndk/inc/bsd" --include_path="C:/ti/ccsv7/tools/compiler/ti-cgt-arm_16.9.0.LTS/include" --include_path="C:/ti/tirtos_tivac_2_16_00_08/products/TivaWare_C_Series-2.1.0.12573c" -g --gcc --define=PART_TM4C1294NCPDT --define=TIRTOS --define=ccs --define=TIVAWARE --define=_INCLUDE_NIMU_CODE --define=ccs="ccs" --display_error_number --diag_wrap=off --diag_warning=225 --gen_func_subsections=on --preproc_with_compile --preproc_dependency="tcpEcho.d_raw" --cmd_file="configPkg/compiler.opt" "../tcpEcho.c"

>> Compilation failure
subdir_rules.mk:16: recipe for target 'tcpEcho.obj' failed
"../tcpEcho.c", line 50: fatal error #1965: cannot open source file "sys/socket.h"
1 catastrophic error detected in the compilation of "../tcpEcho.c".
Compilation terminated.
gmake: *** [tcpEcho.obj] Error 1
gmake: Target 'all' not remade because of errors.

**** Build Finished ****

Here is my  software enviroment :

tirtos_tivac_2_16_00_08

wolfssl-3.12.0

wolfssl compile setting : 

#
# ======== products.mak ========
#
#
# Read the http://processors.wiki.ti.com/index.php/Using_wolfSSL_with_TI-RTOS
# for instructions to download the software required.

# XDC_INSTALL_DIR is the path to XDCtools directory.
XDC_INSTALL_DIR = C:/ti/xdctools_3_32_00_06_core

# BIOS_INSTALL_DIR is the path to TI-RTOS Kernel (SYS/BIOS) directory. If you
# have installed TI-RTOS, it is located in the products/bios_* path.
BIOS_INSTALL_DIR = C:/ti/tirtos_tivac_2_16_00_08/products/bios_6_45_01_29

# NDK_INSTALL_DIR is the path to TI-RTOS NDK directory. If you have
# installed TI-RTOS, it is located in the products/ndk_* path.
NDK_INSTALL_DIR = C:/ti/tirtos_tivac_2_16_00_08/products/ndk_2_25_00_09

# TIVAWARE_INSTALL_DIR is the path to Tivaware driverlib directory. If you have
# installed TI-RTOS, it is located in the products/TivaWare_* path.
TIVAWARE_INSTALL_DIR = C:/ti/tirtos_tivac_2_16_00_08/products/TivaWare_C_Series-2.1.1.71b

# Define the code generation tools path for TI, IAR and GCC ARM compilers.
# If you have installed Code Composer Studio, the TI and GCC compiler are
# located in the ccsv*/tools/compiler/* path.
#
# Leave assignment empty to disable any toolchain.
ti.targets.arm.elf.M4F = C:/ti/ccsv7/tools/compiler/ti-cgt-arm_16.9.0.LTS
iar.targets.arm.M4F =
gnu.targets.arm.M4F =

ccs: 7.3.0.00019

code : (Please visit the site to view this file)

please help on this , thanks . 

Part Number:TMS570LS0232

Tool/software: Code Composer Studio

Hello, TI Engineers

When I use HALCoGen to gennerate some driver codes, I found a sys_selftest.c file. I don't know what the file is used for? I tried to delete it. After it deleted, the project can not be built. when I check map file, it take account of more than 5000B memory. Could anybody help me to delete it?

Thanks!

Regards!

Xinyu

Part Number:TPS61261

Hello

i want  to find a Boost IC

Requirements:

1. Input: 1.2V, output: 3.3V/0.1A

2. Must be in PFM Mode when the output  at  both high and low load currents.

could you help to search it?

Thanks very much!

Part Number:BQ2970

Hi,

I am designing a charge controller for usage in Energy Harvesting applications. This charge controller takes power from the solar panel, and charges 3.7V, Li-Ion battery pack (either 1 or 2 cells depending on energy rating requirement). I am pursuing suitable energy harvester ICs that can work with Solar power, but there is no adequate Battery protection mechanisms like over-charge, over-discharge, over-current, short circuit, etc. So, I am thinking of using a companion protection IC like BQ2970 that can provide good protections. For easy understanding, I have attached the block diagram of the intended charge controlling application. Battery Pack has in-built protections already, but they are also not adequate. Battery pack is provided by an external vendor, that I don't have much control on it. So, I want to provide protection circuitry external to the battery pack as well.

I have gone through BQ2970 (and its series), but there are some issues with it as below.

1. I need over-charge protection of 4.2V for my Li-Ion battery, whereas BQ2970 has 4.275V min. 3.85V for BQ29706 is much lower than the required 4.2V.
2. BQ2970 is actually meant for protection within the battery pack. However I need protection external to the battery pack. Kindly check below attached block diagram.
3. BQ2970 requires external MOSFETs. Our preference is having internal MOSFETs, though this is not a hard requirement.
4. BQ2970 does not seem to fit the protection requirement as per the below intended application (in the block diagram).
5. BQ29700 has Over-discharge cut-off voltage of 2.8V. Once it has cut-off at this voltage, the battery will get charged again based on the solar power. Once it charges to ~3.7V, we want to connect the battery to the load again. I am terming this as Load Re-connect voltage. Such Load re-connect mechanism is not there in BQ2970.
6. We want the IC to have charging/discharging ratings up to at least 0.5A.

Can you suggest any suitable IC that can resolve above issues?

Thanks & Regards,

Vikas Chandra Rao.

Part Number:CC2640

Hello,

I am using simple_peripheral on cc2640. I have PIN 1 as wakeup PIN it should wakeup the other MCU connected to it.

Could you please help me that how i can assert the PIN so the other MCU wakeup from the sleep?

Should i use PIN_setConfig() or any other function for this purpose?

Waiting for your kind reply.

Regards

MAbbas

Part Number:AM3703

We have been using the Flash v1.6 tool for years on Windows XP as part of a factory programming station but was finally required to migrate to Windows 7.  With great difficulty, we were able to get the test system to work with Windows 7, 32bit a year ago.  As PC hardware changes and begins to fail, trying to implement this has been extremely difficult with newer PCs, even though the operating system is the same.  I am using the OMAPFlash.exe command line to program the device, but the script halts and eventually times out (after 20 seconds) with no errors.  The location of the timeout may vary every time the script is ran.  I did not see this failure with older hardware (i.e. Dell Optiplex 790), but get this error repeatedly when trying to run with new hardware (i.e. Dell Optiplex 5050)

Windows 7 is the only option these days.  Is there any direct support for the Flash v1.6 tool in Windows 7, or a direct replacement?  I have tried WinXP compatibility mode, but this was no help. 

 Command line script:

OMAPFlash.exe ^

     -omap 3 -2 -p EVM_MDDR_MICRON_2G -t 20 ^

     chip_erase NANDINFO1BITBOOT 0 ^

     chip_download NANDINFO1BITBOOT "%~dp0\boot_ldr.bin.ift" ^

     chip_download NANDINFOINTECC@20000 "%~dp0\OE_Main_B.Flashtool"

Part Number:LM5071

Tool/software: WEBENCH® Design Tools

I would like to design a PoE powered device which can also powered from an auxiliary power input.

I have the following spec:

Vin = 12...56VDC

Vout = 12VDC, 1.0A

Isolated min. 1.5kV

There is the WEBENCH® Designer for designing your own DC/DC converter. This tool is great.

Can I use the tool also for the LM5071?

Tool/software: Code Composer Studio

Dear Support Team,

we are trying to evaluate Vienna Rectifier based design based on www.ti.com/tool/TIDM-1000. We solved some issues yet, but the GUI will not load.

Let me sum up, what I did until now:

The PC is running Windows 7 64bit in German
.NET Framework 4.7 was already installed
installed Code Composter Studio 7.3.0.00019
fixed some proxy issues
installed GUI Composer Runtime 6.1.0.2 from the CCS App Center
installed controlSUITE 3.4.7 including powerSUITE 1.7.0.00
run F28377D Project from he TI Resource Explorer classic
main.cfg PowerSuite window stays blank

Code Composer Studio gave warnings, so i installed compiler 6.4.6 and XDCtools 3.31.00.24
-> no effect

according to https://e2e.ti.com/support/microcontrollers/c2000/f/171/t/600473:
- open with XGCONF -> no effect
- switched powerSUITE versions -> only 1.7.0.00 worked to run
- same results with different projects
- GUI Composer Test App is running
- chrome debugging gives error as follows:

Installing suggested updates an Eclipse GMF Framework didn't change the result

Part Number:TPS564201

Hello,

we have trouble with the TPS564201 and the UCC3813D-2 in EMC immunity tests for the standart EN61000-4-3. We use the TPS564201 to generate our logic voltage of 3.3V from 12V input.
There are 3 PCBs using this converter. Some of these PCB are built into a fridge, so they are surrounded by a metal housing connected to PE.

Within the first test the PCBs were not mounted into the fridge and supplied by a 12V battery. In this setup (on a table) we had no problems with the immunity test, everything worked fine fine over all frequencies (30MHz-1GHz).
The test is done with an influence with a field strength of 10V/m.

Mounted to the fridge the power supply of 12V is done by our own designed Mainboard including a AC/DC Flyback converter with UCC3813D-2.

Our first "little" problem is, that we can see that the power supply breaks down to ~8V for ~1s for some frequencies (150MHz, 200MHz...) over the whole range.
It looks like the UCC3813D-2 shortly stops regulating the voltage sometimes. It is not a big problem because we use a backup battery, that holds the 12V directly if the power supply breaks down.

What i want to ask is, whether there are some known problems with this IC on immunity tests or some solutions to prevent these problems.

Out big problem is the TPS564201. At influence frequencies of 300-320MHz this IC creates a short circuit and breaks down directly. When the power supply breaks down in the same moment,
and the battery supplies the circuit, the IC makes a short circuit to the battery and burns down directly with enormerous currents.
This problem occurs simultaneously on the mainboard and the other PCB that is not mounted into the fridge (TPS564201 in both cases). This second PCB is a Human Machine Interface and placed in front of the fridge door.

All logic parts behind the TPS564201 are unaffected and the boards work again after replacing the TPS564201, so it looks like a short circuit inside the IC.

Here i have the same question. Are there any recommendations for such problems? Do some sensitive pins of the ICs need a special filtering with RC, LC or CLC filers? Or can you see possible other reasons for this behavour?

It would be nice if someone has an idea.

Thanks.

Best regards
Friedrich Ermert

Part Number:CC3200-LAUNCHXL

Tool/software: Code Composer Studio

Hi,

I am trying to run aws iot v2.1.0-ti on cc3200 and using windows 10. I have flashed all the correct certificates using the certiflasher tool as per the instruction given in readme_cc3200.md file. I have built the subscribe_publish sample application and generated the.out file. Now while running the application, I keep getting the following error

I tried putting breakpoint before line no 114 in subscribe_publish_sample.c (inside the runAWSClient function), but then after reaching the breakpoint it throws an NTP server error and rest of the execution goes same as before.

My endpoint is correct and i have flashed the correct certificates. In cmd i can view my endpoint by the describe-endpoint command and also list the certificates with list-certificates command.

Can anyone please suggest where I am going wrong? Thanks.

Regards,

Sourajit