Part Number: UCC27282
Hello,
could 27282 drive GaN FET? what's the maximum driving frequence?
thank you.
↧
UCC27282: UCC27282 driving GaN
↧
Texas Instruments Dallas/Fort Worth Location - Relocation, Experiences
Part Number: 1
I'm relocating from California to Dallas for an internship next summer at the Dallas/FW area for reliability engineering.
Is there anything I should take note about living in Dallas/FW?
When should I be looking for subleases?
Can anyone briefly talk about their experience working there?
↧
↧
CCS/TMS570LC4357: PIN MUX configuration for SPI, EMIF and UART to work together
Part Number: TMS570LC4357
Tool/software: Code Composer Studio
Hi,
As per my requirement(IICD), if i want to use SPI, EMIF and UART interface together, then the PIN MUX files show the conflicts for the pinmux balls.
Does it mean that i can not use all the interface at a time?, If not then what is the way to change the PIN MUX configurations?
How to make this three work together as far as pinmux is considered?
Please help me to deal with this case.
Regards,
Shivam Kakad
↧
CCS/TMS320F28379D: CCS Examples Compile Error
Part Number: TMS320F28379D
Tool/software: Code Composer Studio
Hi,
I'm using LAUNCHXL-F28379D board with ccs examples and at the first time after installing ccs and control suite and c2000ware softwares, when i open each different examples, i have some errors like make error, unresolved error, make: *** No rule to make target `clean'. Stop. adc_soc_epwm_cpu01 C/C++ Problem ,...
It's so trouble for me and after many searches during previous week, the solution is nothing yet.
Can anyone describe for me the problem and resolve them please?
thank you in advance
Best Regards
Moham
↧
CCS8.3.1 subdir_rules.mk:9: *** unterminated variable reference. Stop.
when I build all, this error occurs. what's the root cause?
↧
↧
Compiler/ADS1198ECGFE-PDK: Device malfunction
Part Number: ADS1198ECGFE-PDK
Tool/software: TI C/C++ Compiler
Hi,
Firstly thanks for taking the time to read my post. I had just bought the ADS198ECH-FE EVA kit and had successfully gotten some good EMG results. However currently, I am getting a lot of random noises in my waveforms. I tried resetting the software settings and acquiring data with all the inputs shorted. I was supposed to get signals in a straight line with no waveforms but instead got the signal below, which shows a lot of random noises. Furthermore, the FFT analysis seems to show that the CMRR is infinite for some channels, which is really wrong. I suspect there is a malfunction on my device. Can you please help me check what the problem may be? Thanks once again.
:
↧
DM385: u-boot spi load
Part Number: DM385
What can be the reason of the following behavior:
While loading u-boot over spi, processor loads couple of 512-byte pages and stops loading?
My bin file looks OK at first sight: it has header with file length (0x0000C0F8), load address (0x40300000)
and byte order opposite to nand version:
00 00 C0 F8 40 30 00 00 EA 00 00 12 E5 9F F0 14 E5 9F F0 14
E5 9F F0 14 E5 9F F0 14 E5 9F F0 14 etc
↧
BQ25703A: Can't read 0x28/29 ADCIBAT() data
Part Number: BQ25703A
Hi,
I used BQ25703A EVM set charging voltage and charging current to let battery charging,
I can measure charging current bu current probe, but I used TI GUI to read BQ25703A 0x28/0x29 data always is 0,
this register should can show charging current, right? or need set other register before I read it?
Thanks!
Jeff
↧
DLP470TP: 4K UST optical engine partners?
Part Number: DLP470TP
I couldn't find any suppliers (optical module partners) from the list who offer 4K (DLP470TP) optical engines (modules) but for Ultra Short Throw (UST).
Are there any?
Plan B is DLP4710 (1080p) UST optical engine, if anyone provides those.
↧
↧
DRV8881: Peak current and SOA
Part Number: DRV8881
Hi,
What is the peak current of DRV8881?
Or can you provide SOA data for internal FET?
Our customer are looking for a device that will not break when the output is short-circuited, and will have a protection operation.
This device has an OCP but OCP has a deglitching time of 2μs.
I would like to judge how much peak current can flow before OCP is applied.
Best regards,
Yuto Sakai
↧
CCS/CC2640R2F: Cc2640r2f how to configure the DMA function of UART in nortos mode.
Part Number: CC2640R2F
Tool/software: Code Composer Studio
Hello, I want to make a simple private protocol packet capturing tool for cc2640r2f. The basic idea is that the serial port receives the content received by RF. I follow the example in nortos mode. When RF receiving function and serial port function are turned on at the same time. Obviously feel the interference of serial port function to RF function. Want to ask cc2640r2f how to configure UART DMA function thank you!
↧
TLE4275-Q1: Question about Stability
Part Number: TLE4275-Q1
Hi Team,
My customer found TLE4275QKTTRQ1 gets oscillating on their prototype board.
Attached is the test circuitry they made for evaluation.
Q.1) Pleas check attached material. (Highest priority)
It looks nothing wrong in setup.
Can you provide measurement result on your Lab with same configuration?
Q.2) Figure 16 in datasheet (Revised November 2014)
I suppose title of X-axis is Load current not Load Capacitance. Could you correct this?
Also, please provide information about Input/output capacitor of this figure?
Q.3) Figure 17 in datasheet (Revised November 2014)
I suppose title of X-axis is Input Capacitance not Load Capacitance. Could you check it?
Best regards,
Nobuo
↧
CCS/CC2642R: the TX power of slave
Part Number: CC2642R
Tool/software: Code Composer Studio
Hi,
I am using CC2642 and V3.2 SDK to develop AOA. Now I find that when the slave and passive is more than 1meter, the RSSI value is always near the same, about 0xa4~ 0xb9. when I move the slave to even 5 meter away or even farther, the value is still this area. I think maybe the tx power is to small. so I check the TX power of slave , as following
.txPower = GAP_ADV_TX_POWER_NO_PREFERENCE (127)
I also try to change the value to 10, but the RSSI area is the same. I am not sure whether the RSSI area is normal or not. if the Tx power matters ,how to change it? and if not, what else can I do? thank you
best regards
Yanpo, Li
↧
↧
CCS/TMS570LS1224: Uart Bootloader application
Part Number: TMS570LS1224
Tool/software: Code Composer Studio
is there any separate bootloader application for TMS570ls1224
↧
MSP430FR6989: Is it feasible to develop an electronic water meter based on MR reluctance element using MSP430FR6989?
Part Number: MSP430FR6989
My customer is developing an electronic water meter based on MR reluctance elements.
They learned from the Internet that TI has a magnetoresistance solution chip MSP430FR6989, which can use magnetoresistance measurement to provide hardware support for electrical signal sampling of magnetoresistance output.
They wanted to know if it would be feasible to develop an electronic water meter based on MR reluctance elements using the MSP430FR6989 scheme. Their water meter USES LCD display and lorawan for wireless data transmission. Thanks.
↧
TMS320F28069M: Question about lab13b
Part Number: TMS320F28069M
Dear team:
In the "ST_runPosMove" function, Occasionally, "STPOSMOVE_getStatus(stObj->posMoveHandle)" will be in "St move bus" state for a long time, At this time, the motor does not rotate, but the motor has self-locking.
I would like to know what cause this and how do I deal with it?
Best regards
↧
NE5534A: Bias current changes
Part Number: NE5534A
Hi All,
We have a problem with DC offset in one of our products, related to the input bias current of the NE5534's that we're using. The issue wasn't present when the product was designed, and it's been in production since about 2006. Unfortunately we don't really know when the issue started to arise, as it's not something we test for routinely in production.
I should stress that the parts we're buying now seem to be within spec, but I suspect that when the product was originally designed either the parts where beating bias-current spec by some margin, or another offset factor was cancelling the effect that we're seeing today.
So my question is, has there been any change in the design or manufacturing process of the NE5534 in the last 10 years or so that might have affected these parameters?
I think the truth is that we may have changed supplier at some point, but I'd like to be able to rule out a change in TI's parts.
Thanks.
↧
↧
SM320C6748-HIREL: Power dissipation and more information about this processor.
Part Number: SM320C6748-HIREL
On the datasheet, it says that "The SM320C6748-HIREL fixed- and floating-point DSP is a low-power applications processor based on a C674x DSP core. This DSP provides significantly lower power than other members of the TMS320C6000™ platform of DSPs."
It's great news! But I didn't find more information about this processor.
What is the manufacture process of this processor? 65 nm?
Is there any datasheet that can tell me the power dissipation of the processor? Just like the <C67484642 power consumption summary.pdf> or the <C6748_46_42_PowerSpreadsheet_RevD.xls>.
So that I can evaluate whether it is worth of replacing TMS320C6748 with SM320C6748 on my product.
Thank youi.
↧
TPS65261-1: V7V pin of TPS65261-1 is not output.
Part Number: TPS65261-1
Hi team.
Customers will use TPS65261 under the following conditions:
PVINx = 5V
Vout1 = 1.1V , Iout1 = 0.28A
Vout2 = 1.5V , Iout2 = 0.52A
Vout3 = 1.0V , Iout3 = 1.25A
The customer wants to control the sequence of this IC with the following configuration
.
figure1
But V7V was not output in this configuration.
If the connection was changed as follows, it worked as expected.
figure2
I want to know why V7V is not output when configuration of figure1.
Vest regards.
↧
BQ2000T: Battery detection
Part Number: BQ2000T
Hi Team,
I have a question about bq2000T battery detection.
How does bq2000T detect battery absent or not since I couldn't find any comment explains "Built-in Battery Removal and Insertion Detection"?
Regards,
Kai
↧