MSP430FR5994: Dual image code is not working.
Part Number:MSP430FR5994Hi,I am running successfully MSP boot-loader code for single image application firmware update. Now i am trying to run code for msp430fr5994 dual image bootloader. After...
View ArticleTDC1000-GASEVM: TDR Time of flight measurement with TDC1000
Part Number:TDC1000-GASEVMI have been working on a project to design TDR based Soil Moisture measurement device. I have bought TDC1000-GASEVM for measurement of time of flight. I have configured all...
View ArticleBQ40Z80: bq40z80 unfounded discharge protection
Part Number:BQ40Z80Hello!We have 7-cell battery. Can't run discharge. Curent lower then -200mA is normal, but higher then -200 mA goes to DCH FET closing. In this tim only BAL_EN register changes its...
View ArticleClik here to view.
SN74AVC1T45: A output abnormal when there is a cap on B input
Part Number:SN74AVC1T45Hi team, My customer is using our SN74AVC1T45DRLR as a logic Level Translator. The direction is from B to A. And the issue is the A output is abnormal when there is a cap(C157)...
View ArticleAutomotive LDO Suggestion
Hi team,May I know TI's LDO has fully protection for output short circuit? In my case, we need 24VDC convert to 12VDC / 60mA for ouput spec and wide input rang up to 60VDC for load dump.Looks...
View ArticleRTOS/TMS320C6678: In TI-RTOS 5.1 version gives error in "clock.xs" file
Part Number:TMS320C6678Tool/software: TI-RTOSHi, I have ported older version TI-RTOS to TI-RTOS 5.1, In beginning it was build good. Now I have made changes in header file inclusion ( just skip some...
View ArticleClik here to view.
PCM1862-Q1: Both SE and Dif option on one card
Part Number:PCM1862-Q1Hi!I'm creating a design for two microphones, it is not sure what kind will be used so I need the card to function either way. Would this design work for both singel ended and...
View ArticleClik here to view.
IWR6843: Not working with DCA1000
Part Number:IWR6843Hi!I am trying to get started with raw data capture using DCA1000+IWR6843.I cannot find a quick start for the 6843, so I followed thee quick guide and hoped for it to work. In...
View ArticleLMX2582: Phase shift of LMX2582
Part Number:LMX2582Hi!I want to try two LMX2582's for clocking two ADC's on different boards TSW40RF80EVM. So need to have synchroniс signal for ADC's. But if I have phase shift beetwin two signals on...
View ArticleClik here to view.
TXB0104: Can TXB0104 be replaced directly by TXS0104E?
Part Number:TXB0104Hi Team,From the TXB0104 datasheet, it says TXB0104 can only translate push-pull CMOS output. TXS0104E is open drain.However, the TXS0104E datasheet says that it can also translate...
View ArticleClik here to view.
CCS/TMS320F28335: ePWM not generating the corect frequencz PWM signals
Part Number:TMS320F28335Tool/software: Code Composer StudioHello Sir, I have used ePWM module in matlab simulink in the model of FOC of 3 phase induction machine I am trying to generate switching...
View ArticleTINA/Spice/ADS1018-Q1: ADS1018-Q1
Part Number:ADS1018-Q1Tool/software:TINA-TI or Spice ModelsHi ,Thank you very much for your support so far. We are working on one requirement as below. We have used ADS1118 for interfacing thermocouple...
View ArticleTINA/Spice/ADS1018-Q1: ADS1018-Q1
Part Number:ADS1018-Q1Tool/software:TINA-TI or Spice ModelsHi ,Thank you very much for your support so far. We are working on one requirement as below. We have used ADS1118 for interfacing thermocouple...
View ArticleClik here to view.
LMR62014: 5V to 6V converter makes lot of heat and unstable output
Part Number:LMR62014I have been testing above circuit to drive a scooter headlight unit rated for about 6 to 7VDC up to 0.5A from 5VDC input.When turned on, led is bright enough but after about 10mins...
View ArticleLM48100Q-Q1: LM48100QMH/NOPB
Part Number:LM48100Q-Q1Hi, Couldn't able to find VOH and VOL in the datasheet. Provide the threshold voltage levels at the output as VOH and VOL. Also, provide the information regarding the operating...
View ArticleTIDEP-0091: LDO bypass setting
Part Number:TIDEP-0091Hi,Can you please explain why the the IWR1443 LDO bypass is disabled by default when the LP87524J is used in auto mode? Isn't the output voltage of Buck2 1V no matter which mode...
View ArticleCCS: Help to begginer with composer :)
Tool/software: Code Composer StudioHi guys ,I don't know if it's the right place to ask ..I'm trying to use GUI composer with CC3200 SimpleLink Launchpad , I just a beginner thus I trying to understand...
View ArticleCC1310: VDDS voltage level & POR trigger
Part Number:CC1310Dear lprf team,I understand from the following post : https://e2e.ti.com/support/wireless-connectivity/sub-1-ghz/f/156/t/635782 that when VDDS goes below 1.8v - 50 mV ie 1.75v then a...
View ArticleCompiler: IPD obtention
Tool/software: TI C/C++ CompilerHelloIn order to obtain the IPD algorithm, I need to contact an FAE.How obtain an FAE?Thank
View ArticleDP83630: DP83630 PTP improvement on stability
Part Number:DP83630Hi,I'm in midst of looking for potential the solutions to improve PTP implementation onto design board which currently uses the DP83630 PTP PHY IC and it's linked up to TMS320DM8148....
View Article