Error e[46] CC2530?
Hi guys,I am trying to use the Sensor Demo that came with ZStack. Since it is an old file I updated all the function calls. (ex. inituart to HalUARTInit etc). When I try to rebuild I get the following...
View ArticleSCI loopback on FM28M35H52C1, no response
Hello All:I am trying out the C28 SCI loopback example code lately, but not getting the desired result. I pretty much load up the example code, and then try to run it. the code get stuck here :...
View ArticleUnable to connect TI XDS100v3 to pandaboard_ES with CC Studio v 5.5.1 . (The...
Hi all,I have purchased a TI XDS100v3 to debug pandaboard but i am unable to connect it . It says The JTAG DR Integrity scan-test has failed.I will be very grateful to you for your HELP!!!!!Execute the...
View ArticleStoring / Reading variables from FLASH on a TM4C123 MC
Hello and nice to meet you all, I'm Jaime and I'm totally new to this forums.I've come here after searching for plenty of time how am I supposed to store and read variables from the FLASH memory. My...
View ArticleTPA3110D2 -Q1 additional graph
Dear all,I think to use TPA3110D2-Q1 for 16Ω and 4Ω speakers.(Gain=20dB, Vcc=8.5V, Output=5W or less)I have some questions to use this device, please teach me your answers.Question 1： I want graph...
View ArticleUnable to connect TI XDS100v3 to pandaboard_ES with CC Studio v 5.5.1 . (The...
Hi all,I have purchased a TI XDS100v3 to debug pandaboard but i am unable to connect it . It says The JTAG DR Integrity scan-test has failed.I will be very grateful to you for your HELP!!!!!Execute the...
View ArticleFatFS f_write returning FR_DISK_ERR?
I am trying to use FreeRTOS and the FatFS library (inside the TivaWare third_party). However I keep getting a FR_DISK_ERR when i try to use f_write.The function I am using is like this: basically it...
View ArticleClik here to view.
F28027: reading EEPROM (I2C) in "burst-mode", how to keep read-out data?
Hi there,I'm new to TMS320F28xxx microprocessors and currently busy to develop the I2C part. In this matter a serial 256kBit EEPROM (slave) shall be partially read out.My question is if it is possible...
View ArticleOne question for c6713 .
I want to build c6713 testcase on ccs 3.3, So I need a c6713.cmd file for it . Can you give me the configure file ?thanks
View ArticleADS1282 Group delay and Settign time min anad max value
Hi,In ADS1282 datasheet , only give Group delay and Setting time TYP value, do you have min and max value provide?
View ArticleTM4C123 Energia sketch results in wrong target
Hello everyone,I am using CCS v6.1 for Linux and Energia 15.So I noticed that when I import or create a Energia sketch in Code Composer Studio the target is actually wrong.It should be TM4C123GH6PM but...
View Articlenew board design won't debug
I have designed a new pcb with the cc3200.I can program the flash using uniflash and update the service pack.I can connect to the board using the target configuration interface.I am using 2 wire debug...
View ArticleSN74ALVTH16374DL Output-Slew Rate
HiSN74ALVTH16374DL Output-Slew RateHow much is Slew-Rate of the output signal?In addition, please provide a simple output constitution figure.Capacity, which is connected to the output terminal is I...
View ArticleHow to add multi-cmd files in a project.
Hi All I am leaning to burn project to Nor Flash. But I have to built 8 times for 8 core by modify cmd files. How can I add multi-cmd files in a project which allows me to built only once for...
View Articlesnprintf not working correctly
Hi,I'm using snprintf to create a char * with data inserted in string format. I came back to the project I was working on, and all of a sudden, my working code was no longer working.Here's what I...
View ArticleAM335X - No NAND device found on SDK8.0 Kernel
Dears,We are bring up the board, but it having a No NAND device found issue on kernel.To dump the uboot GPMC register is different with the kernel,uboot:00000800 001e1e00 001e1e00 16051807...
View ArticleDRV8307: datasheet mismatch schematics. What for?
Hi.While reading datasheet (april 2014) of DRV8307, i spotted a difference between two schematics and i wondered the reason for that.See diagram 9.2, page 22: S1 on FET is wired to motor phases and S2...
View ArticleBQ2060A Development Kit
I just received a TI gas gauge kit for the BQ2060A. I had an older unit for the BQ2013, that worked for me. I am curious because according to the schematic for the new development board, the VCC for...
View ArticleRM48L952ZWT HalCoGen 4.03.00 het.c pwm functions and math precision for float...
Hello. We are using your TI Hercules RM48L942ZWT processor with HalCoGen 4.03.00. for the autogenerated het.c functions -- we had needed the pwmSetSignal and pwmGetSignal - we needed the duty cycle to...
View ArticleClik here to view.
CC254x peripheral and Android 5 Lollipop
This is a continuation of this thread:As that thread is marked as answered and mods don't seem to be visiting it.We still don't have a firm answer from TI as to whether they will update the TI stack. I...
View Article