Multiple connections with SPP
In general, and more specifically using the SPPDemo or the Keyfob demo, can I connect multiple clients to one server?Let's say I have the keyfob demo running, I can establish a connection to one client...
View Articleenabling interrupts in stellarisware
We recently transitioned to LM3S2793-IQC80-C5 date code $A-28. The current processor does not function with our firmware. We replaced the Stellaris processor on a failed PCB with an older lot code...
View ArticleAbout the valuation method of TFP401.
Is there any EVM board for evaluating about the following interfaces? - DVI/HDMI(RX) =>LVDS (TX) - LVDS(RX) =>DVI/HDMI (TX) Although I thought whether to have been the combination of TFP401 and...
View ArticleAM335x Starter Kit TMDSSK3358
Hi,We are trying to craete the Micro SD card for the AM335x Starter Kit TMDSSK3358.But once we are running the script create-sd-card.sh, it gives an error at the end "u-boot.bin file not find".Can...
View ArticleMinicom will not connect to OMAP-L138 board
Hello,I have set up the DVSDK, and then have followed the "OMAPL138 Software Developers Guide" until I got stuck. So far, I have run "{DVSDK}/setup.sh", and used all of the default options except for...
View ArticleEVM6678 adding second RJ45
We have the TMS320C6678 EVM.By now we are successfully using the RJ45 to receive data - raw ethernet from a FPGA. (We started off by using the client example).In our project we would like to interface...
View ArticleADS1299 evaluation kit PCB higher resolution drawings
Hello, could you please post higher resolution drawings of the ADS1299 evaluation board PCB design (pages 54-56) ?Thank you very much.Dino http://www.ti.com/lit/ug/slau443/slau443.pdf
View ArticleClik here to view.
CCS v5.3.0 resource is not a file error while trying to import project
I'm a new guy in this community. So first of all, Hi everyone.I've purchased a DK-LM3S9D96 and downloaded Code Composer Studio v5.3.0 and licenced it with no problem. The CCS is installed on a Windows...
View ArticleNeed documentation
I need a document that describes in detail the flash programming through JTAG of the LM3S6911.I need something that compares to slau320g.pdf document that you published for the MSP430.I cannot seem to...
View ArticleBatch builds fail fro CCS 5.3
We recently migrated a C6455 project from 5.1 to 5.3 to be tool-compatible with the C6678 developers. Our software build correctly when done inside CCS, build our build PC (using batch builds) fails....
View ArticleLMK03001C register readback?
Hello,I'm using the LMK03001C in a design and I'm a little confused. The IO ports on the device are labeled as uWire. The uWire spec (as I understand it) has both input and output capabilities (input...
View Articlecompiling a simple character devide driver for OMAPL138
Hi,In the SDK of OMAPL138 , steps for compiling a application is given . But how to compile a driver is not given . i have written a small driver , now i want to compile it for the OMAPL138 board,...
View ArticleIAR Error [Li005]: no definition for "_c_int00
I am trying to build a HalcoGen project for the RM48 with IAR Embedded Workbench, but I get an Error "no definition for" both _c_int00 and custum_dabort durring linking.I am using IAR version...
View ArticleCorrect way to recover from UART receive timeout on C6748 using PSP 01_30_01...
HiI am trying to use the PSP UART driver with the C6748 with UART 2 and the following setup: uartParams_.opMode = Uart_OpMode_INTERRUPT; uartParams_.baudRate =...
View ArticleCCS5.2.1.00018_linux and ubuntu 12.04 LTS 64bits : XDS560 emu not recognized ...
Hi All,Here's an interesting case I'm phasing :The situation:Ubuntu 12.04LTS 64 bits is freshly installed on a new PC.Installed 32bit application libraries with sudo apt-get install...
View ArticleTPS5430 – The recommended value of FB resistor
I would like to ask a question.A customer is going to use R1=10.2kohm and R2=1.5kohm in the following condition.Is this value the optimal?Also,what is the reason the recommended values of R1 are...
View ArticleUBIFS ECC error issue (0xFF data)
My UBIFS image is mounting properly the first time and after that I am facing a crash on subsequent boots. Also, I observed that whenever a ‘sync’ operation is performed, the subsequent boot fails. I...
View ArticleHow do I unlock my Stepper motor Control RDK board w/ LM3S617 micro?
HI,I tried to compile the qs_stepper code from IAR Systems and I get the following error:---------------------------Driver---------------------------Fatal error: **ERROR**: Unable to open device...
View ArticleRM48 with IAR
I am trying to get a basic HalcoGen App to run using IAR IDE. The code seems to get stuck in mapClocks(). The same setting for HaloGen worked fine in CCS. /* Work Around for Errata SYS#46: *...
View Articlespi to can driver not working
Hi,We're developing on the dm8168 platform along with the z3 board. We are also using the following ezsdk ti-ezsdk_dm816x-evm_5_03_01_15.The problem we're having is that when the mcp251x module tries...
View Article