CCS/CC3220S-LAUNCHXL: Getting "Error: Imported project-spec file not found:...
Part Number:CC3220S-LAUNCHXLTool/software: Code Composer StudioHi,I am trying to follow the instructions of Getting Started Guide for SimpleLink™ Wi-Fi® and Internet of Things Solution CC3220, a...
View ArticleCC2530: Security in SampleLight
Part Number:CC2530Hi,I wanted to know what exactly does setting DSECURE=1 do and what would happen if I set it to 0? When I want to connect the CC2530 to the Smartthings hub, should I enable it or...
View ArticleUCD3138A64: Power consumption in Full mode operation
Part Number:UCD3138A64HelloI need to have an idea about the total power consumption (worse case) in FULL mode operation of the UCD3138A64 digital controller BR Noureddine
View ArticleClik here to view.
BQ24450: Help understand equation to calculate Rp on datasheet pages 13 and 14.
Part Number:BQ24450Hi,I am trying to understand the equation to calculate value of Rp in datasheet SLUS929C (BQ24450) pages 13-14.For the first example using PNP drive transistor, the equation is shown...
View ArticleCCS/TMS320F28335: What target devices are compatible with the Hardware Trace...
Part Number:TMS320F28335Tool/software: Code Composer StudioGreetings,What target devices are compatible with the Hardware Trace Analyzer and/or the System Analyzer?Also, what emulators are supported?...
View ArticleUCD3138A64: documentation for control theory of LLC full bridge conveter
Part Number:UCD3138A64Hello I'am looking for a documentation control theory of LLC full bridge converter. there are any application note for LLC FB converter based on UCD3138Thank you Noureddine
View ArticleDRV8846: Autotune at Power Up
Part Number:DRV8846The data sheet is clear about entering Autotune mode as follows:"pull the ADEC pin to logic high and pull DEC0 and DEC1 pins to logic low. The state of the ADEC pin is only evaluated...
View ArticleRM48L952: SPI1 and SPI2 have same HalCoGen settings, but different outputs
Part Number:RM48L952I am trying to use the RM48L952 HDK board's SPI2 peripheral in Master mode. I originally used SPI1 and was able to verify the code and the HalCoGen settings as working. However,...
View ArticleRTOS/CC2630: How do I change the current time in the destination device?
Part Number:CC2630Tool/software:TI-RTOSHello!I use the CC2630 as the end device and the СС2530 as a router and coordinator.I use Z-Stack Home 1.2.2.I want to change the current time in the end device...
View ArticleMSP430F5529: Not able to write the commands on launchpad
Part Number:MSP430F5529Team,Can you please help with my customer's question below:I am configuring MSP430F5529 Launchpad as a CDC device and trying to communicate it from Ubuntu terminal.I have...
View ArticleRTOS/TMS320C6678: FPGA writing steps to DSP by SRIO
Part Number:TMS320C6678Tool/software:TI-RTOS HiI set " C:\ti\pdk_C6678_1_1_2_6\packages\ti\drv\exampleProjects\SRIO_TputBenchmarkingTestProject " as my base project for communicating to FPGA by SRIO.I...
View ArticleLAUNCHXL-CC1310: Schematic Verification
Part Number:LAUNCHXL-CC1310The schematic as shown on TI (www.ti.com/.../launchxl-cc1310 Documents) provided under the design files, on the "CC1310 RF" page of the schematic, it shows the resistor R12...
View ArticleCCS/MSP-FET: "Could not set device Vcc," remedies available?
Part Number:MSP-FETTool/software: Code Composer StudioCustomer is using MSP-FET with Launchpad for MSP430F5529. He keeps getting error message "Could not set device Vcc." All connections seem correct...
View ArticleSN65DSI84: trying to generate test pattern
Part Number:SN65DSI84Hi I got my boards back with the SN68DSI84 on it and I was trying to configure them to generate a test pattern. I'm putting in a 74.25Mhz reference clock, reset is high, and the...
View ArticleISO124: Isolation amplifier damaged, simple connection setup
Part Number:ISO124Good day,I am using a ISO124 with two switching power supplies both +-12V DC, at the input of the ISO I have a range of 0-5V DC and the 0V reference grounded, at the output I have a...
View ArticleRTOS: UART_Read() missing characterts
Tool/software:TI-RTOSHi AllI added UART to the simple BLE peripheral project and I am having an issue related the UART_read() UART_Params_init(&uartParams); uartParams.writeDataMode =...
View ArticleClik here to view.
DAC38J84: Weird interaction between DAC38J84 and LMK04828
Part Number:DAC38J84I am having a troublesome problem on my design. I have a DAC38j84 being driven by an LMK04828 as is done exactly on the DAC38J84 eval board. I'm using the crystek 122.88 MHz...
View ArticleCC2541: Changing antenna coupling filter discrete parts changing 0402 to 0603...
Part Number:CC2541Have CC2541 product in production. Not very happy with Balun and looking to go to the recommended discrete parts connecting CC2541 to an inverted F antenna.We have copied the example...
View Article