Receiving Raw Ethernet Problem
I'm trying to run the client example on the 6678evm with raw ethernet. via the RJ45 connector.I can send data successfully but do not receive any data...(I'm sending the data from a FPGA or Unix...
View ArticleLinux boot hang on mmc read
I have a beaglebone derived custom board that hangs once it gets to looking for the rootfs off the mmc:Uncompressing Linux... done, booting the kernel.[ 0.000000] Initializing cgroup subsys cpuset[...
View ArticleConcerto ControlCard can't connect to C28 core anymore, C28 no longer...
Hello,I reformatted my PC and installed the latest CCS, XDCtools, SYS/BIOS, and IPC.I have a dual core project that was executing properly before the updates. As part of the project I have each core...
View ArticleLM3481 FET heat dissipation
Hello,I like to learn a bit more on the heat dissipation of the FET using the LM3481 in Sepic mode. Although the setup seams to work ok, It seems my FET is getting too hot. In some cases it desolders...
View Articleads1230 interfacing 8052
Hello Sir, My ADC board is working fine,But some of my customers complainted that after power on the weigh scale,the value slightly increased without any weight on the loadcell upto 1 gm for...
View ArticleCrystal Oscillator Driver to Clock Multiple Devices
Can the crystal oscillator driver SN74LVC1GX04DRLR be used to clock two devices? I would like the SN74LVC1GX04DRLR to connect directly to the DDC114 CLK pin and microcontroller device at 16MHz.
View ArticleThe question about the comunication of CC1101 FIFO mode @OOK_433.92MHz
I really need to help about CC1101 communication:In GFSK mode,the CC1101 can communicate sucessfully at FIFO mode,and I only adjust it to OOK mode,and nothing could be read from RX FIFO.And the...
View ArticleCC1120 - WMBUS preamble problem
HiI'm setting WMBUS register: I've no problem for channel 1a to 3b, but for channel 0 (with modulation 4GFSK) I can't setup preamble register.WMBUS standard says that preamble should be n x (AD), with...
View ArticleDCO UART configuration
Hi,I use msp430fr5739 with uart. I need to use uart with DCO 8 mHz uart with 9600 bpsand i set the board 8 mHz like;WDTCTL = WDTPW + WDTHOLD; PJSEL0 |= BIT4 + BIT5; CSCTL0_H = 0xA5; CSCTL1 |= DCOFSEL0...
View ArticleMPEG-4 encoder
Hello,I would like to ask about MPEG-4 encoder (part 2) for DM8168: I see in user's guide that encoder output file format is .m4v, is it the same as MP4 file format (MPEG-4 part 12) , i.e. does the...
View ArticleHow to design an application with msp430 and perform under 25MHz
Dear friends,The maximum clock of some msp430 microprocessors is about 25MHz.I want to know how to implement the design and let it perform under 25MHz, and what should I take into account in my...
View ArticleMultiple timers on PRU subsystem
I am trying to map some functionality on the PRU subsystem. To implement these functions I will need at least two timers.In the am335x_tech-ref_c.pdf (where the PRU is still described in detail) some...
View ArticleTWL6040 High-performance mode
HiThe datasheet for the TWL6040 claims a dynamic range increase of 5 dB when using High-performance mode (HP) mode. I am not getting this improvement on my device when switching from LP to HP...
View Articletutorial using ccs ver 5.1 trying to run in ccs ver 5.2 tried a miriad of...
The overhead to learn msp430 compiler is extremely daunting especially when there are multitude ccs versions and manuals.(along with related bugs and idiosyncrasy for using software)Is there some clue...
View ArticleFloating point UART
Hello, how can I send a floating point number using UART?I read the documentation of uartstudio.c and didn't see nothing about floating point numbersThank you and happy new year!
View ArticleProblem with launching debugger time
I am using Code Composer Studio (Version: 5.2.0.00069) and work with XDS100 and XDS560 EVM with c6678 DSP.My problem is the time to launch any "Target configuration" takes 5-10 minutes and I think it...
View Article.intvecs and .resetvecs colliding
Hi TI:I was redirected to this forum. I think this will be a pretty easy problem to resolve.I am getting the following error and I do not know how to fix it. "./configPkg/linker.cmd", line 203: error:...
View ArticlePLEASE need some help on ths1206EVM . .
Iam providing an analog input of 0.1 -0.2v to AINP and GND to obtain its digital form . .But i am not able to obtain the outputs. I also have few doubts which are described below : .Is the pin...
View ArticleRunning Hercules Safety demos on RM46HDK
Hi,I am using RM46HDK. After installing CC and Development kit , I tried to run Hercules safety mcu demos on it . But launchpad says "The VI is not executable , The Full LabView..... " . Please...
View ArticleHelp Guys
Hello guys , im using the Code composer studio for the first time , i did not need a burner cuz i can make my own through USB interface , but the problem is that the CCS does not run without kit board...
View Article