[ Config and Start CPU-Timer of DSP TMS320F28335 ]
Hello,In my motion control project, I would like to use the Cpu-Timer0 in order to generate an interrupt every 200us which launch an interrupt service routine "ISRKernel". This interrupt service...
View ArticleSCI in F28069
Hi, I'm debugging SCI echo back example for f28069. But it is halting at // Wait for inc character while(SciaRegs.SCIFFRX.bit.RXFFST !=1) { } // wait for XRDY =1 for empty stateSeems like it is not...
View ArticleClik here to view.
OMAP4 GPMC Synchronous Burst Failure
I try to interface an FPGA with the OMAP4 using the GPMC in synchronous burst mode. The FPGA acts like an FIFO which triggers just on the GPMC_CLK and GPMC_CS signals and outputs the data on the 16Bit...
View ArticleSDK for DM368 IPNC
Hi,Is there any way that i can get the source code of the DM368 IPNC because currently we are planning to develop a custom board by using IPNC as reference so if i could get the source code it would be...
View ArticlesaLoopBack Problem
Hi,I refer the technical user guide "TI81XX Video Capture Driver User Guide.pdf" and "TI81XX VPSS Video Driver User Guide", and others questions in TI E2E Community.So i follow the steps of the...
View ArticleClarification needed for Syslink FAQs
HelloI have already posted a question about that here:http://e2e.ti.com/support/embedded/bios/f/355/t/271771.aspxI'm trying to solve the problem indicated in the Syslink FAQ as...
View ArticleHeap size of G726 Encoder and Decoder
Hi all,I downloaded from the page of the TI G726 Encoder and Decoder c55xx, but there are questions.http://software-dl.ti.com/dsps/dsps_public_sw/codecs/C55X_Speech/index_FDS.html G726 Encoder and...
View ArticleAbout AVSYNC RefClk adjustment from declink
I am using DVRRDK 4.0 to implement decode link for H264decoder.Currently, I have a question that what the timing the reference clock is adjusted.Which is, if the timestamp of the input frame is 33ms,...
View ArticleWL1271 with rowboat-android ics: changing list of profiles in SDP bluetooth
Hi,We're putting a DM3730 with WL1271 based board running rowboat-android 4.0.3 through bluetooth certification. One of the issues we're failing on is that the system is advertising profiles such as...
View ArticleCalculate partition Size
128 mtdblock0 (driver?)128 mtdblock1 (driver?)128 mtdblock2 (driver?)128 mtdblock3 (driver?)1920 mtdblock4 (driver?)128 mtdblock5 (driver?)5120 mtdblock6 (driver?)124672 mtdblock7 (driver?)5120...
View ArticleWebBench filterdesign simulation failes if filterorder is uneven
Simulation of filter response (e.g. step response) fails if the filter order is uneven (e.g. 3 or 5). It looks like there is no connection between the first and the second stage. Can anyone...
View ArticleClik here to view.
TXB0108 pull-up and pull-down resistor
Hi,On the TXB0108, can I use both pull-up and pull-down resistor like below? Best Regards,Hide
View ArticleIssue about MT and UART
I want to know if It's possible in a CC2531(USB) to employ at the same time the Monitor Test module (USB) and the other UART (for example, to connect to other device). Is it possible? I think that...
View Articlefailed connection between CCSv4 and DSK6455
Dear TiI'm working with CCSv4 4.2.5.00005. The OS is windows 7 64 bit Professional edition. My board is a DSK6455 from spectrum Digital. I'm working with them since two years.Last week the system...
View ArticleCCS debug session expression export
Hi,I'm using CCS 5.2.1.00018.My question is, how to export expression values from debugging (mostly arrays) into excel.I'm using the ADC for measurement series, the results are stored into 15 arrays....
View Articleti8148 based custom board always hangs during booting.
Hello All, My board always hangs after this message.I am looking for clues, what could be wrong. In my custom bootloader and uImage, we made some board specific images for muxing, SPI enable, etc.But...
View Articlebq77908a dominant signal, CHGST or Shutdown
Hi community,I am using a bq77908a and want to drive the shutdown by pulling the TS signal down to ground and having ZEDE high at the same time (1 sec shutdown). Now what I don't understand is what...
View ArticleMaximum input current pin A13 on EZ430-RF2500
I would like toknow whichis the maximumpermissible inputcurrenton pinsof the transmitterEZ430-RF2500, as I burned twocouponsand do not understandwhy.I measureditfrom the circuitabsorbsapproximately...
View Article802.11n version of CC3000?
Hello, I'm working on a project for a client that is interested in using the CC3000 but would like an 802.11n version because"any non-N devices slows down all other N devices. So even though we do...
View ArticleAppro DM368-IPNC issues
Hi all, I am trying to run moduletest.out drv_capture and i am getting the output as follows:# ./moduletest.out drv_captureDavinciDisplay DavinciDisplay.1: Before finishing with...
View Article