MCP6S28
Hi,I need to interface MCP6S28 ICs with Stellaris LM3s9D96 MCU....I am confused whether I should use EPI or SSI....Also please guide me about going through the interfacing.
View ArticleDLP3000 without window
Hello,I am under the impression, both from the datasheet and by inspecting the unit, that there is a thin glass window glued on top of the mirrors in the DLP3000. I see that it is possible to buy the...
View ArticleHV Motor Control and PFC Developer's Kit - Position Control
Hi,I am trying to run the "HVPM_Sensored_Servo" example that came with High Voltage Motor Control and PFC Developer's Kit ( TMDSHVMTRPFCKIT ). When I run the project in build level 5, the motor "tries"...
View ArticleEK-LM4F232H5QD uart BAUD RATE ISSUE
I didnt get any serial data for baudrate 9600 while it works fine for 115200. Code i used isfor 115200 baudrate:- ROM_UARTConfigSetExpClk(UART0_BASE, ROM_SysCtlClockGet(),115200,(UART_CONFIG_WLEN_8 |...
View ArticleFrame rate
We have the LightCommander chipset and would like to deliver arbitrary patterns at a frame rate of 1000Hz. Is this possible? If not, would the D4100 kit provide this capability? Thank you.
View ArticleSE profile range ext sample application -- transport key using TC link key...
Hello, I am working with cc2531, zstack 2.5.1a, using the SE sample app Range Extender configuration. I have modified the fw8Config.cfg to specify/* Enable ZigBee-Pro */-DZIGBEEPRO-DSE_PROFILE/* Set...
View ArticleBQ29200 - Cell Balancing Circuit
Hi,I am planning to use BQ29200 mainly as a cell balancing chip for a BMS of 2-series Li cells. I am using another IC (Maxim's DS2777) as the battery monitor, gas gauge and protection. Will there be...
View Articlec6678 IPC .text in MSMCSRAM
Hello,I have an issue with tms320c6678 when I try to debug my own simple application. The application just runs in two cores and one instance send "Notify" to another.When .text section replaced from...
View Articlewhere is the CC-KNX-DK kit?
HI: Anyone has somothing about it? I Had searched it everywhere on the whole ti website.it has no sdk,no reference design.And in the ti store,it is not there.I just got some user guides from the...
View ArticleAV BIOS SDK installable location on web
Hi all,Can anybody please tell me the location of AV BIOS SDK 00.08.00.00 installable path in web so that I can download and install it.Regards,Anup Singh Lamba
View Articlecc4000
i am trying to connect experimental board msp430f5438a with cc4000 using uart, but not able to. are we suppose to use the same clocks for both? i am able to connect between cc4000 and parallax terminal...
View ArticleClik here to view.
First byte gets sent twice when transmitting as SPI slave on CC2530
I'm trying to transmit 4 bytes of data from a CC2530 configured as SPI slave. The problem is that the first byte is always transmitted twice as you can see from the image below taken from a logic...
View ArticleTesting ADS1232
Dear All,We just made a board with ADS1232 connected to a 28069 piccolo processor.We did not have a load cell to check so we just generated a milli volt signal by connecting a potentiometer (10K)...
View Articlequestion about MessageQ_alloc
Hi TI-friends,rdk3.0, dm8168I add "printf" in following inside System_ipcMsgQSendMsg() located in system_ipc_msgq.c under src_linux, printf("@@...
View ArticleWhat will be the behavior in case DSP and EDMA3 controller both tries to...
Hi All , I am trying to understand what will happen if DSP and EDMA both generates request for DDR access at same time ..Below mentioned is the details for the scenario i am referring:-1. The EDMA3 is...
View ArticleReg:msp430
Hi...This is Surender. I am using msp430fr5739.Let me know after JTAG operation, I am using JTAG pins as GPIO Will it be possible? Can you help me in this regard.
View ArticleHow to find the classpath and include .jar files in it
I am using CCSv5.3, and I need to use external packages in Rhino javascript. I need to include the .jar file in the classpath - but I could not find any option to do that. Could anyone please explain...
View ArticleHow to integrate a custom iUniversal algorithm into the RPE of DVRRDK?
Hi, I am trying to integrate an iuniversal algorithm to the rpe system of DVRRDK 3.50 (for TI8168), and yet I have a hardtime in dealing with the xDC-tool, which is used for packaging. By...
View Articleusing HRCAP in RM48L952
We have to measure the frequency of a signal which can be from 0.1 Hz to 300 Hz.Connecting it to a ECAP pin and measuring the events is quite easy and works well.Since we do not have any ECAP pin free,...
View Articlec6678 Task stack overrun
hello:I am using the sysbios, and I use core0 run 4 Tasks, and Core1 run 2 tasks, So the project has 6 Tasks, below is my codevoid main(){ if(DNUM == 0){ Task_create();//.....create 4 tasks}else{...
View Article