NAND data corruption
I am using EZSDK 5.05.02, with NAND-related patches back ported from PSP_04.04.00.02 (EZSDK 5.05.02 comes with PSP 04.04.00.01). Things are working quite well, but I am running in to data corruption...
View ArticleHow to use TI Yocto to build SDK
Some information is not so clear in TI Yocto document: sitara_boot_camp_introduction_to_yocto.pdf.1. After access git: git clone git://arago-project.org/git/projects/oe-layersetup.git, the TI Yocto...
View ArticleStrange problem with I2C Pins.
Hello all,working over a project which needs I2C protocols, m not using default I2C registers,very first i used P3.0, P3.1 for SDA and SCL, with resisters of 4.7k pull-up to 3.3v, don't know how these...
View ArticleCC2543 basic mode operation
Hi,I need to get this chip set running really quickly,Is there any one that has the CC2543 running in basic mode that would share their RF setup & run code?Thanks for your help.Larry
View ArticleCannot Add Link File In CCS5.3.0
I am trying to link some resource in a project In CCS5.3.0.I right click the project, select "add files..." , then select a .c file, and then chose "link to files " and click ok.But nothing happens....
View ArticleBundle or full License of CCS with OMAP L137 EVM
Dear TI !We plan to buy OMAP L137 EVM. It comes with the Code Composer Studio Bundle License?1. Which restrictions has this version of CCS?2. Which opportunities gives me the full License of Code...
View ArticleClik here to view.
TMS570LS3137 control card emulator connection problem
Hi: I am using 3137 card. when I connect board with Blackhawk USB510 Emulator, errors below: I have tryed several emulator already, make me crazy.Thanks.
View ArticleClik here to view.
TRF7970A Operation in ISO14443A emulation
Hi All,In the manual (page 29, rev. G) it says that it is possible to start the transmission right after writing the first byte into the FIFO (quote "Send the transmit command and the number of bytes...
View Articleexception when trying to write to certain memory locations.
Good afternoon,I am writing code for a OMAP3530 EVM board useing CCSv5.3 with SYS/BIOS support. When I try to write to or read from any of the registers assosiated with the general purpose memory...
View ArticleBooting blaze tablet 4460 from SD card
Hi all,I have a blaze tablet 4460 GP ES1.1 and It it booting from emmc and running android. I would like to make it boot and run android from SD card.I saw this post...
View ArticleOpenCL status?
Hi,Can anyone provide an update on the status of OpenCL support for DM8168?Last info I was able to find says it was under development one year ago.Thanks!
View ArticleNDK race condition/improper locking
We are using ndk 2_22_00_06.When the dhcp client cannot renew the IP address until the end of the leasetime, it will try to close all open sockets before requesting a new IP address (in netsrv.c:291)....
View ArticleEVM solutions for a 900MHz ISM band + DSP I/Q modulation
Hi,I am quite new to the forum and didn't know where else to post this question. I am trying to look for an evaluation board that has an RF Transceiver Module which takes in an I/Q input and outputs...
View ArticleTCA9406 internal pullups not working properly
I've got a simple I2C interface design in prototyping, and due to the slow speed of our I2C implementation (10 KHz max) and short runs, I opted to use the internal 10K pullups in this part. However, in...
View ArticleClik here to view.
TivaWare Clickwrap license agreement shows up with blank Software Name,...
Hello, Just an FYI - the TivaWare installer has nothing in the Software Name or Version fields. I downloaded the version that's on the website today, June 12th.
View ArticleClik here to view.
schematic feedback
Could I get some feedback on my attached schematic? I'm trying to layout a small dev board that will support USB and USB Bootstrap loading. I've gone through as much material as I can find to gain...
View Articleerror #10099-D: program will not fit into available memory
Hello,I built a very simple application for TMSF28335 using Code Composer 5.2.0.00069.I created an empty project for this DSP and used 28335_RAM_lnk.cmd with no changes.The code is:#include...
View ArticleHow to add mathlib to a 6678 project?
Hi,I am using TMDSEVM6678le and I try to add mathlib libraryin order to use sindp function, here what I did still now:1) I added mathlib.h header file to my main .c file2) Included paths in...
View ArticleRelease Scheudle Update : TM4C123GH6PM
Hello,Can you pleae provide the latest release scheudle for the Tiva 4: TM4C123GH6PMThank you.
View Article1000 points FFT Audio compensation
Hi, My customer is working on a stereo home audio system and has an idea to add an fixed compensation circuit to it. They want to add a fixed 1000 or 1024 points FFT coefficients to the audio signal...
View Article