BAR0 not visible from RC
Dear support,I hope you can help me with this very strange issue that we are experiencing. I am not sure if I should classify my problemas a Boot Issue or Pcie Issue.The RBL enables the C6670 to boot...
View ArticleMSP430FR5729 timer A0 behaves different than MSP430F2274 timer A
I have two pieces of coda that are almost exactly the same. Code was originally written for MSP430F2274 but recently ported th MSP430FR5729.The code is for a programmable medical stimulation device,...
View Articledm814x low power modes?
Hello,I'm trying to implement a low power mode for when our product goes idle. I still need the CPU, serial port, USB, and ethernet connection to be active, but I am trying to shut off everything else...
View ArticleDisparity error checking in TLK1501?
Does the TLK1501 receiver check running disparity of the incoming serial signal? There appears to be no comment on this in the datasheet. Similar parts, like the TLK3134, report an error on the...
View Articleundefined symbol FS$$MPY
I am getting undefined symbol references.......CCS V3.3, 28335.... i was able to find information on this that suggests i need to include the RTS library but i am including...
View ArticleDSS Rhino Debugger will not launch
All,I am trying to enable Rhino Debugger. First this is first according to this link, with Rhino Debugger i can write my javascript in Rhino, output the result of my script to Rhino instead of the cmd,...
View Articleslow (/2) MMC/SD clocking
I have a question about the MMC/SD clock. My board has the following clock settings:ARM9_0: GEL Output: ---------------------------------------------ARM9_0: GEL Output: | PLL0 Information |ARM9_0: GEL...
View ArticleClik here to view.
Problem with start bit detection with F5438A
Hello,I'm experiencing a strange behavior from the UART of an MSP430F5438a.I read 10 bytes every 500ms and in about 10% of the cases the start bit is not detected correctly and it is read as a data bit...
View ArticleFedora 18 floating license server ethernet ports not named eth0
In the post http://e2e.ti.com/support/development_tools/code_composer_studio/f/81/p/207940/751289.aspx#751289 it discusses this problem but with Fedora 15. The problem is the license server needs the...
View ArticleCompiler error in yvals.h and Xutility.h
Hi All, I had a compilation error [originating out of this folder related files <TI INSTALLATION PATH>\ccsv5\tools\compiler\c6000_7.4.1\include].There are two files in that...
View ArticleDAC8728 latching and power-up sequencing
Hi,On page 41 of the DAC8728 it talks about the power sequencing. Since usually a 5V regulator is fed from +15V, and perhaps 3.3V regulator fed from the 5V or 15V, the power up sequencing is really...
View ArticleUnable to connect to DLP Lightcrafter via USB
I have firmware and software package 2.0 from the TI page installed, and when I connect the Lightcrafter to a windows 7 computer via USB, it shows up under network adapters as an RNDIS gadget with a...
View ArticleMSP430UIF Problem Under Linux
I have installed CCS 5.4.0.00091 for linux,Linux localhost.localdomain 3.9.4-200.fc18.x86_64 #1 SMP Fri May 24 20:10:49 UTC 2013 x86_64 x86_64 x86_64 GNU/Linuxabout a week ago. I am now trying to get a...
View Articlewhat is the possible cases that Inode gets deleted
hi,I am using SD-card for booting linux, i have created one partition for boot and one for rootfs and tried both EXT2 and EXT3 fs, but the problem is inode reference gets deleted and its trowing...
View Articleflashloader.bin download
Hello, I am looking for the "flashloader.bin" file that can be reprogrammed onto a device that has had teh flash loader erased. I have searched the TI site and found what I thought was the correct...
View ArticleABS07 Crystal - MSP430F5328
Good afternoon.I am unable to get the above external 32kHz crystal (Abracon part) to work with the XT1 on the 5328. I have configured P2.2 as the SMCLK for verification and am monitoring with a scope....
View ArticleUSB development by combining MSP430 USB dev pack, and OMAP Starterware ?
The MSP430 USB development pack, among other things, greatly helps develop software for the WINDOWS side of a USB-HID communication link. This Windows software is written in C using the Windows Visual...
View Articledynamic control of PINMUX registers between Hi-Z and any valid pin function
Hi, I have a question about the dynamic control of PINMUX registers between Hi-Z and any valid pin function on C674x platform. One of my customers wants to use some GPIOs as an output or Hi-Z, and they...
View ArticleClik here to view.
InstaSpin QuadCopter
Youtube Video:http://youtu.be/xETai-9nZOQThe board contains 4 special piccolo devices which have a sensorless softwareencoder in ROM. The Piccolo devices sense each phase current andvoltage and...
View Articlehow to display data using graph menu??
hello ,my board is 6678Le,my ccs version is CCS5.3. i want to use the graph fuction to display data which is defined from my project . int x[4096]={...} the dot in the "{}" denotes sinewave data i...
View Article