CC1125 use with MSP430f5507. Cannot access radio
Hi everyone!I am having a problem with the communication between my MSP430f5507 and my CC1125. I have based my software on the spi access coes from TI:s software examples for the TRxEB. Anyhow when I...
View ArticleClik here to view.
CCS5.4 installation failure
HiI am trying to install CCS5.4 on Windows XP. It fails with the error shown above. Anti-virus ondemand scanning is disabled. I have also attached the install jammer log.How can I fix this...
View ArticleDVRRDK qeustion on SYSTEM_VIDEO_LINK
I am using DVR RDK 3.0 and has a usecase of cap -> ..... -> IPC_OUT_M3 - > IPC_IN_M3 -> enc -> .... working normally.now I try adding some link between IPC_IN_M3 and enc, becoming .......
View ArticleDM8148 ISS SDK setting problem if I want to change another parallel interface...
Hello everyone,I have a DM8148 EVB board, VCAM(video camera application board) board and MT9P031 parallel camera hardware and IPNC ezsdk.I run vc demo application and this MT9P031 sensor works fine.I...
View ArticleUSCI UCMODE Clarification
I am implementing my first project with SPI communication using the USCI peripheral. I am using the MSP430G2533 and am a little confused by the 3-pin vs 4-pin modes. I know what they are in theory...
View ArticleHow to transfer changed value from arm to dsp
could anyone help me ?I have a parm "Analysis_Begin" in the ARM application code.it uses to call different code in DSP server.But I notice only the first value of Analysis_Begin(FALSE) was...
View ArticleTrouble with callback about EDMA3
hi,dear supports:hardware:DM648Recently ,I used EDMA3 LLD to transfer processed data from L1DSRAM to DDR or SDRAM. My tese case used EDMA3 1D-copy to transfer image data.so Bcnt = 1,Ccnt =1 andusing...
View ArticleClik here to view.
am335x porting problem
We make a custom AM335x board , it reference AM335x EVM. what difference between TI AM335x EVM and our custom AM335x board. TI AM335x EVM custom AM335x...
View ArticleClik here to view.
lwip sockets problem in TMS570LS3137
Hi:Now I encountered a porblem when compling the project, I want to use the sockets of the lwip. Then I obey the suggestions below to change the LWIP_SOCKETS, NO_SYS and LWIP_NETCONN to be 1,1,0....
View ArticleHeadphone output TAS5706
Hi,Speaker output is working with TAS5706.Now I want audio output on headphone. We have connected HPSEL pin GND.In this case what register do i need to chagne?I have enable HP mode by changing system...
View ArticleEvaluation Board LM5118 - LM5118EVAL
Hi there, i'm seriously interessted in the Evaluation Board AN-1819 LM5118. I got some questions about this module. What i need is a buck/boost-converter which provides a output of 10 A. Is it possible...
View ArticleMP Exception raised with reserved bit set in MPFSR
Hi,One of the guys here has just experienced a memory protection fault where one of the reserved bits in the L2 MPFSR is set, despite the manual indicating that they should always read as zero.The...
View ArticleConcerto ARM Application Start from Bootloader
Hello,since I'm able now to program my application to FLASH from an bootloader project I want to know how to start the application from it.The bootloader resides in different sections than the...
View ArticleWriting/reading registers. ICE board.
Hello,I am still very new to this board, but I am usually able to read and write registers using HWREG.But here is my problem. I am trying to read the industrial inputs via Read_HVS(); that we can find...
View ArticleClik here to view.
ZC cannot get data from ZD
When ZD sends Data to ZC, there is no APS ACK from ZC.in the case of Good, Ubiqua displays below1st step, ZD sends Data, "ZCL Reserved"2nd step, ZC sends MAC ACK, "MAC Ack"3rd step, ZC sends APS ACK,...
View ArticleThe VPss is locked up when "Overlow" detected。how can it be avoided？
I`m using a DM8168 board with DVR_RDK3.0 and encounter a big problem： VPSSM3 sometimes gets locked up When I disconnect or reconnect the video input cable. The debug message is as follows:...
View Article[DM8168 DVR_RDK3.0] It's No Effective To Set FPS With Encode!
DearAll, In my usecase,I try to set Fps in runtime or creating time, both two way have no Effect(also no Err).The chain is "srcLink -> ipcOutVpss-> ipcInVideo -> encLink -> ipcOutVideo...
View ArticleCCS 5.4 installation failure
Hello,I have downloaded ccs_setup_5.4.0.00091 offline version installer. I unzipped the contents and ran setup.exe. However, I can't finish the installation as it ran into an error.My system is WinXP...
View ArticleTMS320DM8168 DDR3
Hi all,I am using TMS320DM8168 in one of my application.In reference evaluation Board, EDJ1108DBSE has been used as DDR3 memory, Which is having 256 MB Memory,so for 1GB memory i need to use four 256MB...
View Article28335:All internal RAM-68K bytes can be used as code section?
Hi,Sir!The total size (Code size and data size) of my project is less then 68K bytes, so I want to load all code from flash memory into internal RAM. is it OK? how to deal with secure zone and...
View Article