DM365-USB transfer speed is slow.
hello, i had attach SSD hard disk (having ext3 partition) with my DM365. I simply read raw data by directly open /dev/sdb with buffer size 512 byte. I get speed around 9-10 MBPS. when i attach same...
View ArticleHow to modify SampleLight to send other HomeAutomation command
Hi,I use the SampleLight example as the coordinator and SampleSwitch as End-Device in CC2530EVK with Z-Stack 2.5.1a.The example code work fine.But I want to add other HomeAutomation command (ex. send...
View ArticleCC USB Firmware Library and Examples supporting for CC2543/44 ?
Hi, Is there any plan to support CC2543/44 in CC USB Firmware Library and Examples ? Or how could we manually change for CC2543/44 ? Also, where could I find the CC2543/44 Example Software Supported...
View ArticleAM335x MMU Not Working
I am working on getting MMU working on AM335x, we have our own custom board (closer design to Beagleboard) with NAND flashi am able to boot from NAND flash, now i want to use MMU in my code, i am using...
View ArticleDeveloping StarterWare on BeagleBone Black
Hi,Just got my BB Black. Looks very nice. But without a JTAG, how do I do development for StarterWare? I am a SW folk and I don't want to do soldering...Thanks
View ArticleClik here to view.
UCC28070 OVP problem at load step?
I'm currently developing a 1700W PFC with UCC28070.It works but when I'm at 115VAC and 1700W output and I'm running a step load test from 100% to 50% (1700W to 850W), I have a small overshoot on my...
View ArticleU-boot, writing to MMC (SD)
Hi,I'm using AM3352.I want to write the img and rootfs files to the blank MMC (SD), after booting u-boot in USB Boot Mode.Is it possible by using released environment in SDK (v05.06.00)?ThanksNomoto
View ArticleMake BeagleBone-DVI-D Cape Functional
Hello EveryoneFor my upcoming SYSbios work, i need to have display up on BeagleBone-DVI-D Cape.And I have installed SYSbios_Industial_SDK and tested available gpioLEDBlink application on...
View ArticleHow to implement the object count on the DVRRDK 04.00.00.03
hi, allI want to fulfill the function of object counting ,but after I type the "./run.sh" I only see the 5 items as follow 1: VCAP + VENC + VDEC + VDIS - Progressive SD Encode + Decode 2: VCAP + VENC +...
View Article1920x1080, 10bit frame, raw data to DM8168
I build a vision machine, and I have a source of 1080p/10bit image sensor, working in 30fps.The frame injected to the DM8168 directly from proprietary FPGA (not through TVP5158/7002) , into video port...
View Articlethere is a voltage on the input ADC
Dear all,I'm having a problem with the ADC input of the TMS320F28069.When I turn on the ADC clock, in ADC input pins there are about 900mV.This voltage adds to the voltage of my signal, so the...
View ArticleC6678 SRIO reset function
I'm using the C6678 SRIO to communicate with Altera stritix IV，Program can run successfully after being loaded。Well，I add a reset function in this program like this: srioRegs->RIO_PLM_EN =...
View ArticleClik here to view.
Enquiry about current measurement
Hi, my problem is this; i need to measure current over DC circuit where the DC power polarity is casual. It is assimilable to the AC circuit and the shunt resistor go one time on the high side and one...
View ArticleData corruptions problem in AM3505/17 Android system
During my development using AM3505, I frequently find the UBI data partition is corrupted by some unknown reason. It is resulting the system can’t startup or the application is damage.This problem may...
View Articlewhen STOP and START conditions does not change
Hi, can any explain me when UCTXSTT and UCTXSTP bits will not set its values even if we try to assign values to it. thank you.
View ArticleDMA 32 bit Datasize behaviour
Hi,I am using the DMA of my TMS320F28335 to transfer the ADC results toRAM (XINTF7).I have configured the datasize of the DMA to 32 bit. In order to transfer 16 results ( each 16 bit ), I would think...
View ArticleCRC or checksum
In IAR, there is a CRC or checksum calculator embedded, you can specify the code range, then the calculator will output CRC or checksum into a specified address. Dose CCS have same tool?
View Articleh264fhdvenc 01_10_02_06 encode 1080p abnormal issue
Hi, When I use this codec to encode 1080P, the X64P is generated successfully, but when I use it to encode, the result is: the I frame is good, but the size is a little large, but P frame size is 12...
View ArticleHow to set up and generate .lst file with C and Assembly mixed code?
Hi,Sir!It is very important for optimize C code if we can see C and Assembly code in .lst one line by one line. How to config these settings in project property->build?
View ArticleIntegrate YUV sensor for IPNC App V2.6
Hi,I am working with IPNC DM368 App V2.6. I tried to compile the cramfs and kernel follow the YUV sensor driver integration document but I can't not run it.I always get some problem relate to memory,...
View Article