DRV8811 Decay Mode Select
Hi,I am a new user of the DRM8811. What determines the Decay Mode that I should select for my application?Thanks,Mike
View ArticleEmergent! What happen to 8168? Thanks!
Hi, I am using RDK4.0 and 8168 run for 4 hours later, it print the log show bellow. Could you tell me what happen to 8168?Thanks!Best regards![16250.790000] Unable to handle kernel paging...
View ArticlePCIE issue in DM8168EVM board
Hello,I found the pcie interface can't work normally now, which can't detect the device(RTL8111C） nic which works well in other board).SW5-1 (PCIe RST) switch was set to OFF.(near PCIE SLOT)when power...
View ArticleNeed help enabling ethernet port on 8148 EVM board
Hello,Can anyone provide some suggestions on how I enable the ethernet port on an 8148 EVM board?I have confirmed that the mac address is set in uboot, and have set a static ip address with network...
View ArticleHow to get the source code for Hwi_create()
HiI want to study the how Hwi_create() works, but there is no source code for Hwi_create(). Now I have a question, as SYS/BIOS 6.x is provided with full source code and requires no runtime license...
View ArticleSelection of DM8148 OR DM3730
Hi,We are planning to develop a Video encoder & Decoder which can take input from three analog (PAL) camera , digitize it, compress it (H.264) and simultaneously stream it on LAN OR USB. Resolution...
View ArticleC5515 ezDSP audio template project
Hello all,I am attaching a project that could serve as a starting point for anyone trying to program an audio processing application on a C5515 eZDSP kit. I have not used the CSL library, since I could...
View ArticleInductor L243 value/part number in the sensortag reference design swrr109a
Hi,The reference design swrr109a for the sensortag is missing the value and part number for the antenna impedance matching inductor L243. Does anyone one know the part number or value/specs ?Thanks for...
View ArticleGERBER REQUEST FOR PMP2645 USING TPS40055PWP
Dear Sir,Request you to provide gerber for PMP2645. This is required for an infotainment solution.Regards
View ArticleTPS54332's function of no load (0A) condition
Please teach us TPS54332.Customer tried to check TPS54332's function on their board.Their setting of Vin/Vout is following.Vin ：5.2VVout ：1.18VWhen no load condition of output(0A), customer confirmed...
View ArticleI2C not woking
hi all,M new bie in I2C and m using MSP430F53xx series of controller for controlling and updating registers of PCM9211 using I2C, for this i picked up a example code of CCS 5.2 for sending multiple...
View ArticleThere is a mistake in document SPNU508A (User's Guide of RM48 Hercules...
Please check the document User's Guide of RM48 Hercules Development Kit (HDK) (SPNU508A, Revised September 2012). It should be Table 2-6 for J9, Expansion Connector P1 and Table 2-7 for J10, Expansion...
View ArticleClik here to view.
When I use XDS100V2 Debug my F28335 board, it does'nt work because of device...
How to change 28027 into 28335? I have select 28335 device while newing the target config file.
View ArticleCodec Engine Examples on BeagleBoard xM (DM3730)
Hello I use A BeagleBoard xM with a DM3730 SoC and try to get the audio1_copy example from the CodecEngine to work. To build it i used OpenEmbedded. The standard loadmodules.sh were not able to load so...
View ArticleConcerto microcontroller FM28M35H52C1
DEAR FRIENDS,Is FM28M35H52C1 recommended for new designs? If not can anybody tell me an equivalent part for the same. Because we are unable get the sourcing of this IC from TI itselfPl .helpGirish
View ArticleProblem with proj_lab12 / drv8301kit_revD + TMDSCNCD28069MISO controlCARD
Hi,I tried to test the new motorware1.01.00.06. But I have some trouble with lab12. The Motor doesn't move - not even a little bit. Lab02a works perfect - as well as lab7 (but I miss a description). I...
View ArticleLM22670 adequate for Conversion +5V -> -3.3V, 2A ?
Hello,I need an inverting switching regulator for the conversion from +5V to -3.3V and a current of 2A. In another application I am using the LM22670 for the conversion from +12V to -5V. Because of...
View ArticleDRV201YMBR
Hello,we are using the voice coil motor (VCM),we intend to change the direction of the motor using driver, the part number of driver is "DRV201YMBR" , So please do inform is it possible to change the...
View Article1080p HDMI or Component video capture on DM8168
Hi all,I've been browsing the forums here for a few days and I cannot get a straight answer as to how to get this working.I've got the DM8168 EVM with the VC expansion board (two HDMI inputs &...
View ArticleCompiler error for missing include file is hard to interpret
HiWe are running CCS 5.3 and CGT 7.2.4. I frequently find that the compiler error output is difficult to interpret for the case where a header file is missing.For example, consider the case...
View Article