Clik here to view.
CC1352P: USB to Serial/UART using FT231XS-R
Part Number: CC1352PHi,I am putting together a circuit primarily based on the CC1352P and would like to expose the UART interface via FTDI's FT231XS-R USB to Serial IC - so I can power and communicate...
View ArticleLM5041: AN1299 LM5041 Evaluation board.
Part Number: LM5041Dear Sir,Kindly share the explanation whole circuit to below application note of TI.AN1299 LM5041 Evaluation board.Regards,Marish
View ArticleBQ76PL455A: Unable to Communicate
Part Number: BQ76PL455AHi,We are working on the BQ76PL455A custom board.We have done the following for initialization1. Low Wake pin2.Since we have one device so we fix address as "0x00"3. And we send...
View ArticleAM3359: U-boot memory map
Part Number: AM3359Hi,I am in process or setting up environment variables in u-boot for AM3359 device. I am using TI SDK 05_03.00_07.My SDRAM size is 256 Mbytes, so my total memory map would be as...
View ArticleClik here to view.
Compiler/PROCESSOR-SDK-DRA8X: Picture captured from camera module can't work
Part Number: PROCESSOR-SDK-DRA8XTool/software: TI C/C++ CompilerDear TII use the camera which has ISP in camera module, The sensor is AR0233, the ISP is GW5200, the serializer is TI953, the...
View ArticleClik here to view.
CCS/SFRA: How to measure successfully the frequency response of the buck...
Part Number: SFRATool/software: Code Composer StudioDear Support,I am using the SFRA tool to obtain the plant and open loop frequency response of the buck converter system controled an F28035.According...
View ArticleTPS3808: Replace LTC2955
Part Number: TPS3808Dear Team,What is the suitable solution to replace LTC2955?BRKevin
View ArticleClik here to view.
TMS320F280049C: how to set ADC mux?
Part Number: TMS320F280049CHi,when use ADC of F280049C, we find the pin mux as below:but how should I set it as I want (eg: PIN23 set as A0)? I only find GPIO MUX in datasheet.thanks.Yuan
View ArticleTMS570LS3137: HET interrupts
Part Number: TMS570LS3137Hi Team,I am using HET module with interrupts configured as HET level 1. In micro instruction, I am expecting to get interrupt when the pulse count reaches to a 6 and pulse...
View ArticleDP83822I: DP83822I Compliance Testing Scripts
Part Number: DP83822IHello support team,My customer is working to pass 10BASE-T compliance test. They refer application note SNLA266 and have some questions. *When they run "A.3 10BASE-Te Standard Test...
View ArticleAM3352: IEEE-1588 PTP Grandmaster reference design
Part Number: AM3352Does TI have a IEEE-1588 PTP Grandmaster hardware reference design for the AM335x?
View ArticleClik here to view.
UCC28951-Q1: The duty cycle of Vds will decrease when the shunt down
Part Number: UCC28951-Q1Hi team,my customer use UCC28951-Q1 and have an issue is that when the shunt down, the duty cycle of Vds and gate driver signal will decrease ,please see the below picture.The...
View ArticleCC2652R: zed rejoin
Part Number: CC2652RIs it true that , zigbee End Device should send an ‘orphan’ package to re-join the original network after it disconnect from the network? Original zed switch device directly send...
View ArticleCCS/MSP430I2040: Metering EVM
Part Number: MSP430I2040Tool/software: Code Composer StudioHello ,We have followed reference design of MSP430i2040 submeter EVM for our application.Edited code as per application, now we are at tuning...
View ArticleClik here to view.
Compiler/CC2642R: Getting Linking Error When we enabled the Checksum through IAR
Part Number: CC2642RTool/software: TI C/C++ CompilerHi Team, We are getting a linking error when we enabled the checksum through IAR Linker options. It is showing that it is already used by...
View ArticleTPS1H100-Q1: Resistor Package on CL pin
Part Number: TPS1H100-Q1Hi team,Could you please help to check the recommended package for the resistor on CL pin, which is used to set the current limit?Seems the power consumption on this resistor is...
View ArticleTCAN4550: SPI support CPOL=0; CPHA=1
Part Number: TCAN4550Hi Expert,Whether TCAN4550 can support SPI timming with CPOL=0; CPHA=1?Thanks.Zhou
View Article[FAQ] Software related queries based on mmWave SDK
Here is a list of queries based on mmWave SDK (SW) Q1. How to create a new mmwave sensor project from scratch [Project0]?Answer: Please refer this thread-...
View ArticleClik here to view.
LAUNCHXL-F28379D: use of PLL block in simulink.
Part Number: LAUNCHXL-F28379DHello, I am working with the F28379D control board. I need to work with the PLL block in Matlab Simulink. But, it shows some errors when compiling.Here is the model I used...
View ArticleCCS/BQ34Z950: Battery cycle count not increase by 1 it set to 65303 or and...
Part Number: BQ34Z950Tool/software: Code Composer StudioHello,I am using BQ2040 Battery Pack.I have already using this with our Previous Project, now in my new project one problem arrived that when i...
View Article