Clik here to view.
BQ40Z50-R2: battery management
Part Number: BQ40Z50-R2After the circuit is connected to the computer by EV2400, the short circuit protection is found.But I'm not charging or discharging the battery.The bit register situation is as...
View ArticleCCS/AWR1843BOOST: No getting Programmed
Part Number: AWR1843BOOSTTool/software: Code Composer StudioHi. I recently got a mmWave AWR1843BOOST kit. I tested few debuggings were all fine.. But I thought of erasing using UniFlash Erase SFlash...
View ArticleXTR111: MOSFET Heating Issue
Part Number: XTR111When i powered up my device the output is correct but after powered up the device mosfet start heating and continuously increases.Attached schematic of the design, MOSFET Used -...
View ArticleClik here to view.
BQ40Z50-R2: battery management: can not open the mos
Part Number: BQ40Z50-R2After the software configuration is completed, charging and discharging MOS cannot be opened through the FET_EN command. Is it about software configuration or the welding of the...
View ArticleClik here to view.
LM3481: Unable to load SEPIC to Full load @8V using LM3481.
Part Number: LM3481Hi, I am trying to design Sepic converter using LM3481 with the below sepicifications. I did simulation in Pspcie tool. Also find the attached diagram of SimulationInput range -...
View ArticleTIDA-01632: TIDA-01632
Part Number: TIDA-01632Dear TI partners： Could we use the 24MHz and 32.768KHz crystals just meet the description of reference BOM, is there any other to take care if we use other vendors'...
View ArticleTMS570LS1224: F021 Flash API TI-FEE driver heap usage
Part Number: TMS570LS1224Hi,I have just generated code from Halcogen for TI-FEE Driver and I have noticed that it added .sysmem section to the linker command file:.sysmem : {} > RAMIs the F021...
View ArticleClik here to view.
WEBENCH® Tools/LM3481: Unable to load SEPIC to Full load @8V using LM3481.
Part Number: LM3481Tool/software: WEBENCH® Design ToolsHi, I am trying to design Sepic converter using LM3481 with the below sepicifications. I did simulation in Pspcie tool. Also find the attached...
View ArticleClik here to view.
BQ40Z50-R2: battery management: short-circuit protection
Part Number: BQ40Z50-R2After connecting the circuit to the computer via EV2400, a short circuit protection appeared. However, I did not charge or discharge the battery at this time.What is the cause of...
View ArticleClik here to view.
WEBENCH® Tools/LM3481: Unable to load SEPIC to Full load @8V using LM3481.
Part Number: LM3481Tool/software: WEBENCH® Design ToolsHi, I am trying to design Sepic converter using LM3481 with the below sepicifications. I did simulation in Pspcie tool. Also find the attached...
View ArticleCCS/CC1310: IAR perform mass erase before flashing
Part Number: CC1310Tool/software: Code Composer Studiohi,I was in the IAR performed “options --> debugger --> download -->perform mass erase before flashing” .And then ，In debug mode to power...
View ArticleFDC2214: Frequency resolution calculation
Part Number: FDC2214Hi,I'm developing a capacitive wetness sensor which uses the FDC2214. For my calculations and documentation I would like to take a closer look at the resolution of my...
View ArticleTMS320C6678: Power consumption in extended version.
Part Number: TMS320C6678We are currently using a TMS320C6678ACYP in our application. At high ambient temperature we experience thermal runaway in the device. We have considered changing to the extended...
View ArticleAMC1311-Q1: AMC1311-Q1 power off , we measurement Vout voltage difference was...
Part Number: AMC1311-Q1Dear,We use AMC1311-Q1, and we find some question:if we power off and we measurement VOUTP、VOUTN (C84) have 2.5V voltage difference, it's will effect Next stage OPA.schematic as...
View ArticleAWR1443: Question for AWR1443
Part Number: AWR1443Hi Team,Customer used AWR1443+DCA1000EVM. Because it is easy to oxidize, he bought a shell and put it up. He would like to know how to test the performance of the radome?Thanks.
View ArticleTPS55340: How to fix Css capacitor value ?
Part Number: TPS55340Hi, At the startup of the TPS55340 there is a current peak that I'd like to get rid off. Accordinf to the Datasheet it can be modulated by the Css capacitor. It is already fixed at...
View ArticleClik here to view.
DCA1000EVM: Data unpacking format in complex format
Part Number: DCA1000EVMHi Team,Customer used the DCA1000EVM to collect 1843BOOST. 1843 related unpacking format was not found in Mmwave Radar Device ADC Raw Data Capture document when using complex...
View ArticleClik here to view.
DRV8312-C2-KIT: Abnormal high-speed operation
The software path I used: D:\ti\controlSUITE\development_kits\DRV8312-C2-KIT_v128\BLDC_SensoredHardware:DRV8312EVM RevDI set the program to run in Level6.When I use the BLDC motor provided by TI...
View ArticleADS1293EVM: Confirm if there are additional hardware is required to make this...
Part Number: ADS1293EVMHi Team,We have customer inquiry regarding their application for ADS1293EVM below:Our customer contacted us regarding p/n ADS1293EVM. They would like to know if additional...
View ArticleBQ24725A: Changing from BQ24617 to BQ24725A
Part Number: BQ24725AI'm looking to update a design that uses a 4 cell Li Ion, 14.8V, 2.6Ah battery. Max charge 1.9A CC, 16.8V CV. Point of concern is the higher current consumption of BQ24725A when...
View Article