What is the Task concept in TI RTOS
Hi,I need 2 different functionalities, that can run parallel.My use case is like this,I wanted to read ADC readings from cc2650 with a predefined interval and store the value to a global buffer. When...
View ArticleIs there any board that connect TSIP on EVM6678 and landline phones?
Hi Champs,I`m looking for a board that can connect TSIP on AMC edge connector of EVM6678 and landline phones? I'm planning to evaluate the C6678 TSIP with landline phones.So, could you please let me...
View ArticleClik here to view.
TPS5430 for Output -5V/-9V from Input +12V
I am planning to use below schematic using TPS5430 for -5V/-9V application.Both voltages for op-amp sensing application ( medical grade instrument ) and load requirement is not more than 50 mA.For -5V...
View ArticleBluetopia Build Fails
Hi,I am trying to build bluetopia for wl18xx chip on imx6 sololite processor and using 3.0.35-2508-g54750ff kernel version.And i am facing the below...
View ArticleCAN bootloader for TMS320f28035
Hi all,I am using TMS320F28035 as my Target MCU. So i want to write Bootloader code for my Target MCU so as to update MCU flash over the air.But since i am intended to update the flash through CAN...
View ArticleClik here to view.
ADC coding for SCR gate controller
Hello,I am trying to make firmware code for a SCR controller.Need to work how I can make my 8 analog input voltage to ADC and generate PWM (for R,S,T phase) considering zero crossing and firing angle...
View Articlehow is pin muxing done in TMS320F28075
i couldn't find the pin muxing step in ur adc_soc_epwm_cpu01 example .as per my understanding its done using GPxMUXx registers,is there any other way?what is meant by trim values in this examples, what...
View ArticleHow do the CC1350 run the TI BLE software stack ( which enables full BLE...
hi,We need use the BLE profile to connect smart phone and use the sub -1G to send data.How do the CC1350 run the TI BLE software stack ( which enables full BLE connectivity) and the sub-1G sensor...
View ArticleClik here to view.
Error while flashing .elf file on cc2650 using xds110 device debugger pack.
I am frequently facing these errors, i updated the firmware of Debugger devpack, but still these errors are showing at the time of flashing. I am using XDS110, cc2650, CCS uniflash 3.4 on ubuntu 14.04.
View ArticleCCS v6 is not getting installed on Opensuse Leap 42.1
Hi Everyone!!!I am trying to install CCS on Opensuse Leap 42.1.My version of CCS is: 6.1.3.00034.I tried using the offline installer available on the wiki page.1) First of all, it gives me the...
View ArticleClik here to view.
THCV231 and THCV236 according to TI's solution
Hola,Does TI have a solution which similar with THCV231 and THCV236 below and can support HiSPi？ Thanks ～(Please visit the site to view this file)
View ArticleXDS200 connection problem
I just purchased an XDS200 debug probe. I have been successfully using an Olimex xds100v2 device but wanted a faster device. The target is a custom board with a TM4C1294 Tiva processor. Using CCS...
View ArticleTPS25810 can't charge device problem
Dear sir: Currently we meet TPS25810 can't charge device(Google Nexus) problem. We have test the CC1 and CC2 is 3.85V, we use 5.1K resistor to pull CC2 to ground, it's still 3.7V, Vbus is...
View ArticleInfluence in capacitive measurements
FDC 2212 works well to capacitive sensors but in some applications it is not always pure capacitor it is sometimes influenced by plasma, for example, in this situation the capacitor become an impedance...
View ArticleAM335x eMMC programming with Uniflash
hi everyone:i design a board with cpu am3359, is similar to beaglebone black.emmc is empty now, so i refer to http://processors.wiki.ti.com/index.php/Sitara_Uniflash_Flash_Programming_with_Linux to...
View ArticleUCC28881 isolated flyback solution to output 5V@500mA
Hi Team,Is there any reference design using UCC28881 to converter 90-264VAC to 5V@500mA in isolated flyback topology?There is a reference circuit on data sheet page 25 but customer need detail...
View ArticleConfiguring WiFI SSID parameters in MSP432 TI RTOS tcp echo example.
Hi,I am using the tcp example of TI RTOS on MSP432 with CC3100. The example requires configuration via the Simple Link Starter app right now. Is there a way to define the configuration parameters in...
View ArticleClik here to view.
ti-processor-sdk-linux-am335x-evm-03.00.00.04-Linux-x86-Install.bin, Failed...
I installed the new Linux distribution ti-processor-sdk-linux-am335x-evm-03.00.00.04-Linux-x86-Install.bin: on my board am335x and on my host Ubuntu 16.04, 64 bits.I created a HelloWorld project in CCS...
View ArticleDoes CC2640 BLE stack2.2 support PG2.2 as well?
Hi,Does CC2640 BLE stack2.2 support PG2.2 as well?Any different setting between support PG2.2 and PG2.3?Vivian
View ArticlePorting application code from TDA2x to TDA3x
Hi,I am working on porting the application from tda2x to tda3x.Currently the application runs fine on tda2x.The application uses bios,xdc,ipc,bsp,edma,ivahd,eve,vlib,mathlib packages from vision sdk.On...
View Article