Getting a binary boot file to run, and also the cleaner
I am trying to get a boot file to run on my 5515EVM board. I have successfully taken the *.out file and converted it to a *.bin file. I was able to load the binary boot file per the Wiki's guidance...
View Articlecc2540: Sending value from pc to Dongle using UART.
Hi!I would like to send a value from the pc to the dongle, through UART.Is it possible to program the Dongle so that a callback event is set, whenever there is a value, from the pc, written to it?Note:...
View ArticleRTC counting too fast on lm4f120xl launchpad
hi,i want to use the hibernation modul for a realtime clock and date with my launchpad for an data loggerevereything ist working fine, but the rtc counts approximately 1% too fast.Did i forget...
View Article66AK2H12 's price?
66AK2H12 's price and avaiablity??I can't find where is 66AK2H12 's pricethe purchase text is grey..I try to make very powerful tablet for designer.but I must know how much it is . and is it possible I...
View ArticleHow TO CHOOSE ANTENNA FOR CC2541
hi all. As i am going to do BIOMETRIC USB MASS STORAGE APPLICATION (authentication) PURPOSE . I need BLUETOOTH CHIP for my project to interface with my MCU. so I choose chip CC2541...
View Articlefixed regulators
Hi, Can you suggest me a fixed voltage regulator which takes 5V and outputs -2.5 and +2.5. I am using ADS 1248 and I want to connect AVss to the input side of the regulator.Thanks,
View ArticleClik here to view.
Flash Boot Utilities error TMS320C6748 "Waiting for SFT on the OMAP-L138... "
Hi Everybody,We have design a custom board with TMS320C6748 DSP for one of our project. Using CCS5.1 for code development and using XDS100v2 USB JTAG Emulator. In debug version, I am able test the...
View ArticleCCS/CGT INTERNAL ERROR: Decomposition error occured
Hello,I got the following compiler error message. Could you tell me what's the cause? I tried to add -gcc option, but this didn't solve my problem.- DSP: C66xx- CCS: v5.1.1- CGT: v7.4.2INTERNAL ERROR:...
View ArticleError - hex2000.exe
Hi,I have one question regarding Hex2000.exe utility.When I executed the hex2000, I had an error as the below.--------------------------C:\C2000 Code Generation Tools 5.2.12\bin>hex2000...
View ArticleRadiation Test Data
Bit of a strange question for this forum, but...Is there any radiation data available for the TMS470 or TMS570, or has anyone attempted this previously (SEU and total dose)?cheersMat
View ArticleTUSB2046BI-Q1 recommended Vcc supply voltage range of data-sheet
Page 5 of TUSB2046BI-Q1 data-sheet(SLLSE50) specify that recommended Vcc supply voltage is 3.3V minimum and 3.6V maximum.But Figure 11. 12.13 use 3.3V LDO for Vcc power supply.I think recommended Vcc...
View ArticleUsing CCSv5.x with DSP/BIOS 5.20.x
Hello,Is it possible to use CCSv5.x (hopefully, CCSv5.3) with DSP/BIOS 5.20.x ?I'm asking this because I'm wondering if CCSv3.x may be mandatory whenever we need DSP/BIOS from ROM at C672x devices.The...
View ArticlePassword
HelloWhere do we can change the password of our accounts?I could not find the option Regards
View ArticleUSB Host MSC Example Concerto
Hello,I have problems using the "usb_host_msc" example on M3. Similar to Abhijit kelkar in a former post I run into a Fault ISR. The program detects the USB stick but it encounters problems with...
View ArticleClik here to view.
Some doubts on SLAA512--《Using TI Technology to Simplify Bluetooth Pairing...
Hi everyone,I am a new guy on RFID\NFC,and I'm pluzzed by Ti's describtion when i look over page22 on SLAA512.I don't know why a prefixed byte "0x02" or "0x03" turns up her. so I look over...
View Articlebq24190 - Sharing D+/D- USB lines with host
Hello,The product I'm working on requires requires USB communication (handled by the host) while the battery is charging from USB VBUS.Can a host and a bq24190 share the USB D+/D- lines? If so, how?
View ArticleWhy name change from Stellaris to Tiva?
Hello, I see on the TI home page that the Stellaris M4F line has been renamed to Tiva. Why the change of name? They're now called the "4C" series - I assume they still have the floating point M4F...
View ArticleDCO setting with respect ot BCL12
Hi,I a little bit confused after reading BCL12 case. Is there any thing wrong with the following code when we consider BCL12, or any other things about updating DCO?...
View ArticleHow to connect MSP-FET 430 UIF emulation tool via SPY BI WIRE
Hello: I wanted to reprogram the MSP430F5529 microcontroller on ADS1292R EKG FE board via SPY BI WIRE. Bought the MSP-FET 430 UIF emulation hardware tool for which is suppose to program via JTAG...
View ArticleWatchdog on LM4F232H5QD rev B0 not working when debugger not connected
It seems that I am unable to utilize any of the StellarisWare Watchdog functions when I disconnect the JTAG debugger from our custom board. I have put in some debug code to spit stuff out a UART to...
View Article