Linux/TMDXIDK5718: Processor SDK 6.0: fatal error: openssl/bio.h: No such...
Part Number: TMDXIDK5718Tool/software: LinuxHi,I installed and set up RT Linux SDK6.0 for IDK571 and got below when making the kernel ("make linux" on top level)....HOSTCC...
View ArticleLinux/TDA2EVM5777: Running Linux TIDL exmaples on VAYU VISION APPLICATION BOARD
Part Number: TDA2EVM5777Tool/software: LinuxHello,We have an "ASSY 516620 - VAYU VISION APPLICATION BOARD".Our goal is to build a Linux image that has tidl examples.In order to build the Linux system -...
View ArticleCC2652R: i need to sample up to 6 ch in parallel or min delay one to the other
Part Number: CC2652RHello everybody , I need to idealy sample 6 ch in parallel:500 samples from each channel @ 5 KHz sampling freq for about 1 sec .as far as I understand there is only one sample...
View ArticleTMS320F28034: Ask suggestion how to reduce the failure rate during mass...
Part Number: TMS320F28034Hi,My customer has 20pcs out of 20Ku products which failed to programming by JTAG on production line. Program image by CCS 3.3 + Arrow Seed XDS510 emulator.Is there any advice...
View ArticleBQ78350-R1: EDV Gauging : "Better Calculation" Compensation of temperature
Part Number: BQ78350-R1Hello again,Thank you for the lot of help in the past. We have a battery pack 10s6p BQ78350 BQ76930. I would like to have a question regarding to the calibration and EDV/CEDV...
View ArticleTPS51220A: routing question
Part Number: TPS51220AHi Sir,Because my customer used four layer MB so have layout space concern, if CSP and CSN signal through the inductor bottom but have separate two layer(inductor in top, trace...
View ArticleCCS/TMS320F28335: CPU Timer 2 interrupt not working
Part Number: TMS320F28335Tool/software: Code Composer StudioHi,I am trying to use Timer o and Timer 2 interrupt for internal use in my code. Timer 0 interrupt is working fine but when I configured...
View ArticleTMS320F280049: QCTMRLAT equal to 0 & QCPRDLAT != 0 & while the UPEVNT...
Part Number: TMS320F280049Hi Team, My customer reported an issue for QCTMRLAT = 0 unexpected while in QCLM = 0. At the same time QCPRDLAT is same as previous period(not updated). While using the...
View ArticleClik here to view.
TCA4311A: SCL_OUT and SDA_OUT impedance when disable
Part Number: TCA4311AHi,Are SCL_OUT and SDA_OUT impedance when TCA4311A is disabled by EN pin?Thanks.
View ArticleClik here to view.
BQ27542-G1: BQ27542-G1 current reading error
Part Number: BQ27542-G1As the picture show, why my MCU can read 65324 mA, the reading seems to have overflowed. And my I2C communication rate is 400KHZ.
View ArticleTDA2X - TIDL model EVE execution
Hi everyone,I am working with Pedestrian detection model trained in Caffe framework. I made conversion to TIDL format and results for sample image after conversion are as expected. Bounding box is...
View ArticleTPS22976: Inquiry on the suitable supply voltage to the chip.
Part Number: TPS22976Hi,I would like to ask if I can supply 1.8V to Vbias (PIN 4) of TPS22976.Based on the datasheet in pin functions table, the recommended voltage range is 2.5V to 5.7V.In the...
View ArticleClik here to view.
DP83822I: TX_CLK be interleaved at MII mode (TX_Dx data be received at the...
Part Number: DP83822IHi Team,My customer is using DP83822I as MII mode operation with Register [0X0017] be set as '0049', but when capture the TX_CLK, TX_Dx & RX_CLK, RX_Dx waveform, found a issue...
View ArticleBQ25601: Changing minimum battery voltage when SYS will shut down.
Part Number: BQ25601Dear Team,I'm experimenting with a BQ25601 charger IC to be suitable for our application. One of the problems I'm experiencing right now is to prevent the output voltage to fall...
View ArticleClik here to view.
TPS2373: VC_IN connection
Part Number: TPS2373Hello If customer do not connect to Xfmer aux bias supply to VC_IN due to it is module. How to provide and what voltage to VC_IN of TPS2373? Could pull VDD voltage input...
View ArticleLMK04821: LMK04821_SUPPORT
Part Number: LMK04821Hi,We are using LMK04821 IC. With external clock frequency of 10Mhz, Is it possible to generate SYSREF=120Mhz, DIVCLK= 122.88Mhz?. Kindly reply ASAP. Thanks and regards,Lakshmi M B
View ArticleClik here to view.
TPS53515: Frequency instability issue at Fsw=600KHz
Part Number: TPS53515Vin=12V, Vout=0.8V/8A application, Cin=44uF and Cout=350PF. The detail schematic as follows:When Fsw=600KHZ, the frequency isn't satble. The wave for SW point is in the below:But...
View ArticleCCS/CODECOMPOSER: CODE COMPOSER CANanalyser
Part Number: CODECOMPOSERTool/software: Code Composer StudioHi guys,I actually working in a project where I'm using Matlab/Simulink (program file), TMS320F28335 micro-controller (connected to...
View ArticleLMK00301: Input and output circuit questions
Part Number: LMK00301Dear all,My customer using LMK00301, below questions need your help:1. If LVPECL level crystal is used and AC coupling to the input of LMK00301, then how to set the outside bias...
View ArticleAWR1642BOOST: Writing my own lab
Part Number: AWR1642BOOSTHi guys,How can I write my own lab? I want a lab that displays the range-time and range-doppler heat maps in real time for up-to 15m. The GUI to have an option of recording the...
View Article