YUV range supported on MJPEG Encoder
Hi everyone,Does anyone know which YCbCr range the MJPEG encoder uses? Can MJPEG encoder be configured either YCbCr full range or YCbCr studio range?Best RegardsAngel
View ArticleUsing a function generator rather than a TCXO with the CC1120
Hi,I was wondering if it was possible to use a function generator to input a sine or square wave through a series capacitor into the CC1120 EXT_XOSC pin rather than a TCXO? I know the datasheet says...
View ArticleTPS62153 output resistive divider value?
Hello,In the data sheet, page 9, section 8.3.1, it says : "the internal resistive divider pulls down the output voltage smoothly". I need more info on the divider because I want to drive a 5V rail...
View ArticleClik here to view.
TCA4311A apparent bus corruption
Hi,I'm having some trouble with my I2C bus, especially (but not necessarily the fault of the TCA) when the TCA4311A is connecting two I2C busses.The I2C bus is as follows:I2C Master (Analog BF518)...
View ArticleClik here to view.
LM5116 Using Prototype Board
I would like to prototype the LM5116 using the attached board using conventional thru-hole components. What type of complications might I have in doing so? Or is it necessary to use SMD components...
View ArticleTwo borders of DLP Lightcrafter Evaluation model are always in off position
I have been using the DLP Lightcrafter Evaluation Model to stream HDMI signal for roughly 6 months, but now two of my borders, totaling roughly 20% of the DMD on each side, are always stuck in the off...
View ArticleWL18xx Build Utilities Error
I'm currently trying to build the files for the WL18xx and SDK 2.00.00.00 with Linux 4.1.6 using the build utilities as described here: processors.wiki.ti.com/index.php/WL18xx_System_Build_Scripts for...
View ArticleOV, UV, OCP, monitoring & balancing solution for 16 cell series / 48V /...
Hello BMS Experts,I'm working with a customer on a BMS based on 16 series cells (partitioned into 4 packs of 4 cells). The cell chemistry is LiNiMnCoO2. What ICs can possibly support this set-up? I'm...
View ArticleSystem Analyzer does not collect data.
I am using CCS 6.1.2.00015 in Linux and I am trying to collect data with System Analyzer. I have a Spectrum Digital XDS200 connected to a CC1310, ROV is opened and the target is running. In Live...
View ArticleCompile failure CC2650 SimpleBLEPeripheral standbyPolicy with most recent...
Using the latest and greatest ti downloads, on IAR Workbench 7.50.1 using the imported SimpleBLEPeripheral_custom_argvars, I get a make failure when it reads appBLE.cfg that refers to a property...
View Articlereal-time clock in code composer
I need to write a program that implements a real-time clock in code composer studio. The LCD display shows hours , minutes and seconds . By pressing a button you can enter / exit in setting mode which...
View ArticleWhat signal splitter terminations
Hello, I am planning to add a second port to an existing drive of a TFT display panel. To drive two twin displays I plan a signal splitter circuit described by the attached schematic.My question is, do...
View ArticleTHS788 - Event Input
Hi,For THS788, could you tell me if the Event Input ( 200Mhz) is per channel or all channels combined? Looking at the Event Logic block in the datasheet, I believe they are combined but would like...
View Articlecannot enter isr
#include "driverlib.h" /* Application Defines */ #define TIMER_PERIOD 127 #define DUTY_CYCLE1 64 /* Timer_A Up Configuration Parameter */ const Timer_A_UpModeConfig upConfig = {...
View ArticleDriving Ultrasonic Transducer
Because my system needs higher power for the ultrasonic transducer, I need to drive the transducer with higher voltage.I came up with following ideas driving transducer with 10V peak to peak voltage.a)...
View ArticleProblems installing drivers in Windows 7
After formatting my computer I wanted to install the drivers for the TM4C123G LaunchPad again but when I plug it into a USB port I can´t see the three In-Circuit Debug Interface devices whit yellow...
View ArticleClik here to view.
Serial interface distorted by DAC128S085
Hi there,I'm having a little trouble with the DAC128S085 that maybe someone else has seen before. It seems that the DAC is driving some voltage into the serial pins for the first couple of clock...
View ArticleClik here to view.
CC1310 rfWSN Example
Hi to all, Semaphore_construct(&radioAccessSem, 1, &semParam); Semaphore_construct(&radioResultSem, 0, &semParam); What's the differences of the actual ARGUMENTS of 1 and 0 in the...
View ArticleHow to transmit the attribute data by using the application's callback...
Hi all： there is a attribute which was set as NULL. I want to transmit the data of this attribute by using the application's callback function. 1. I register the...
View ArticleAds1271, reference voltage driver op amp
Dear all, I need to use full bandwidth of ADS1271 (DC included). I'd use an OPA277 instead of OPA350 (mentioned in datasheet). I is more stable in DC mode and also more accessible to me. Would you...
View Article