Clik here to view.
DAC38RF80EVM: DUAL DAC mode crashes instantly after set up of DAC B - User's...
Part Number:DAC38RF80EVMHello all,I have a critical fail when I try to run the DAC38RF80EVM configuration in DUAL DAC mode, following the CMODE 3 example given in the DAC38RF8xEVM User's...
View ArticleTS3DV642: Is it possible to make a HDMI 1:2 spliter device with TS3DV642?
Part Number:TS3DV642Hi ti : I am trying to make a HDMI 1:2 spliter that can split 1 channel HDMI source(video only) to 2 channels of HDMI output. The 2 outputs are copy to each other. I just found...
View ArticleRTOS/CC1310: Battery-powered application using TI 15.4 and power management...
Part Number:CC1310Tool/software: TI-RTOSHi, I am working on an application based on TI15.4 stack that demands the end-nodes to be battery powered. I was exploring the power management api of the...
View ArticleCCS/TIDM-1000: run code from ram by using the solution adapter of powerSUITE
Part Number:TIDM-1000Tool/software: Code Composer Studiohi, how should I use the solution adapter of powerSUITE to configure the setup procedure of my code? I want to load the code in flash zone but...
View ArticleAM3352: What does it happen when am335x misses the first boot time from NAND
Part Number:AM3352Hello, TI expertIf am335x boot from NAND, but NAND is not ready at the first boot time. Can am335x boot from NAND later? And if am335x can, how much time it needed when it misses the...
View ArticleTMS320C28346: BSDL File Problem
Part Number:TMS320C28346Hi,When loading the BSDL file for the TMS320C28346 (sprm424) into our BSDL environment, the software gives the following warning:Invalid pin name VSS on component Device 1...
View ArticleTCA8418: What is the proper startup procedure for the TCA8418 to recognize...
Part Number:TCA8418I have a case where a user should hold down a few keys before powering the device. Is there a way for the TCA8418 to pick up these held keys and generate an interrupt when it starts...
View ArticleSN65HVD72: Extra components.
Part Number:SN65HVD72We will need a simple communication protocol(RS-485) over a twisted pair(RJ45 CAT 5) for the new sensor and communicate to other PCB in the future. We have chosen to use the...
View ArticleTDA2: EVE: BAM buffer transfer
Part Number:TDA2Hi,Are there any limitations or guidelines to buffer transfer within a kernel, or in between different kernels? Is there any document which specifies this? I am facing issues in both...
View ArticleCCS/BLE-STACK: Advertising with delays.
Part Number:BLE-STACKTool/software: Code Composer StudioHello, I am working on project_zero example, I have updated my DEFAULT_ADVERTISING_INTERVAL to 16000 (i.e. 10 seconds). and advertising mode is...
View ArticleClik here to view.
AWR1642BOOST: One of two boards not working
Part Number:AWR1642BOOSTHello,one of our sensors isn't working, please see pictures below. The left picture shows the defect sensor, the right picture shows the working sensor. Further below is a...
View ArticleClik here to view.
CC2642 use clock_construct() to time 1s but real 5s
hi TI professor,I use the function of clock_construct() to time 1s but 5s in real world. when I use the clock tool in CCS to count period, it is 48M and CC2642 clock is 48M.
View ArticleCC2640R2F: Hardware revision
Part Number:CC2640R2FHello,I have been reviewing the errata document (SWRZ085) published last September associated with the CC2640R2F SoC. In trying to determine the chip hardware revision, I am...
View ArticleClik here to view.
ISO7721: Using ISO7721 instead of optoisolator
Part Number:ISO7721Hi,I'm currently using optoisolator(MOCD207M) for charge enable of my design. PIN1- ANODE 1: 3.3V+470ohm serial resistorPIN2-GND_APIN8-COLLECTOR 1: Pin of ICPIN9-EMITTER 1: GND_BThe...
View ArticleCCS/C2000-GANG: ERROR 70: DSP CLK frequency error
Part Number:C2000-GANGTool/software: Code Composer StudioHi,I have tried for first time the C2000-GAN programmer in our custom designed board (MCU TMS320F28027 running at 60MHz from internal clock). I...
View ArticleMSP430FR6047: Is is possible to use the MSP430FR6047 for multiple path system...
Part Number:MSP430FR6047Dear Community members,Will the MSP430FR6047 ship suitable for multiple path (2 paths or 4 paths) ultrasonic system. As they are only 2 channels available on the ship.RegardsMr....
View ArticleTDA2: EVE application code does not execute on board
Part Number:TDA2Hi,I have created an application that should run on EVE. When I execute this application on EVE Simulator (ccs v5 Vayu simulator), it runs correctly and generates expected output. But...
View ArticleDP83867IS: Rise/Fall Times
Part Number:DP83867ISHello,Do we spec rise/fall times on the MDIO interface?Don
View ArticleLinux/AM5708: Using Weston with RGB888 on AM5708 with Dual LVDS
Part Number:AM5708Tool/software: LinuxHow do I set Weston to use RGB888 (not xrgb888, not rgb565) on AM5708?If I set it to "rgb888" via /etc/weston.ini, Weston does not come up:[18:37:19.166] weston...
View Articleble5_simple_peripheral_cc26x2r1lp_app define task ID can not more than 6
hi Ti professor, According to ble5_simple_peripheral_cc26x2r1lp_app, I want to create 4 tasks.The ICall_createRemoteTasks() task priority is 5 and SimplePeripheral_createTask() priority is 1. When I...
View Article