WEBENCH® Tools: Report getting generated as servlet
Tool/software: WEBENCH® Design ToolsHi all,I have created a project in WEBENCH. But when i click to open the report WebenchReportServet of 26 bytes is generated. How do i open pdf report?
View ArticleLMX2594: Loop filter bandwidth vesus VCO modulation bandwidth
Part Number:LMX2594Hi,We are trying to increase the loopfilter bandwidth in the evaluation board from 250kHz to 750kHz. We need this 750kHz loopfilter bandwidth to achieve the ramp linearity that we...
View ArticleClik here to view.
EVM430-FR6047: result is liters per hour?
Part Number:EVM430-FR6047Hi,I'm working on a water meter, based on this exampleI'm not sure if the result stored in the struct USS_Algorithms_Results.volumeFlowRate at ussSwLib.h is on liters/meter or...
View ArticleCC1352R: Optical fiber design recommendation
Part Number:CC1352RHello,I am working on a project that requires both wireless and wired communication over long distances. So we have decided to use the CC11352R MCU as it supports the Sub-1GHz...
View ArticleClik here to view.
TINA/Spice/TPS2121: Encrypted Pspice model generates warning message
Part Number:TPS2121Tool/software:TINA-TI or Spice ModelsWhen trying to use the Pspice encrypted model for the TPS2121 in Pspice 16.2, my customer received the following message from the Pspice model...
View ArticleClik here to view.
INA199: Output Saturated at -300mV When Attempting to Sense Current on -12V Rail
Part Number:INA199Shown above is my configuration for a -12V rail current sensor using the INA199A2DCKT. The "RAW_-12V" net is the power supply rail. The"-12_SENSOR" net is connected to the load. The...
View ArticleClik here to view.
CCS/TMS320F28335: hardware resets
Part Number:TMS320F28335Tool/software: Code Composer StudioHelloI'm a new f28335 user, so after running some examples, I tried to use my hardware for data processing, as the code below. int i,j,h,x,...
View ArticleCompiler/CC2640R2F: SaBLE-x-R2 debugg problems
Part Number:CC2640R2FTool/software: TI C/C++ CompilerHello,I am using the SaBLE-x-R2 development board i have encountered a problem. Namely, I would like to run the code using the step by stem mode in...
View ArticleLMG5200: Current limitation
Part Number:LMG5200TIDA-00909 uses the LMG5200 with a maximum current of 10A. Would it be reasonable to parallel two LMG5200s to deliver 20A? Are the characteristics of the LMG5200 such that they...
View ArticleClik here to view.
DAC70508: DAC Output off by a factor of 4
Part Number:DAC70508I believe I've configured my device correctly however I must have made a mistake since the output voltage out of my DAC's is only 0-1.25V instead of 0-5V. I'm using a voltage to...
View ArticleBQ40Z50-R2: thermistor bias voltage
Part Number:BQ40Z50-R2Hi,an engineer is asking what is the BIAS voltage used for the thermistors? Can it be modified/ set /calibrated?Thank you!Regards,Alberto
View ArticleLinux/TMS320DM8148: CPSW port shutdown
Part Number:TMS320DM8148Tool/software: LinuxHi,We have a custom design based on the DM8148 DSP. This DSP supports 2 MAC ports and we are using both. Both ports use DP83867 PHY.We are having a problem...
View ArticleBQ25898: Bq25898 emi issue
Part Number:BQ25898Hi,I am using this IC in a cellular wireless device for charging the battery. I am experiencing lots of emi from this IC which is screwing up the receiver especially in the frequency...
View ArticleTMDS181:
Part Number:TMDS181Dear TI support team,I have some questions which concerns the TMDS181. I'm using this chip on the sink side in combination with a Kintex7 FPGA as an HDMI 2.0/1.4 capable receiver....
View ArticleSN6501: 5.7kVrms transformer recommendation
Part Number:SN6501Hi Team,My customer is interested in using the SN6501 along with the ISO7842 to achieve a configuration similar to Figure 18 in the ISO7842 datasheet (Isolated RS-232 Interface).With...
View Article[FAQ] What does 'partial power down' or 'Ioff' mean in the datasheet?
The "Ioff" specification in the electrical characteristics table is only in the datasheet of devices that have the special feature of "partial power down" - also known as "back-drive...
View ArticleCCS/MSP430F5508: Resolved CCS/MSP430F5508: Driver signing when using MSP430...
Part Number:MSP430F5508Tool/software: Code Composer StudioI have a follow-up question to my post here: e2e.ti.com/.../2791687. I figured I would copy this question into its own follow-up thread.I have...
View ArticleCCS/PROCESSOR-SDK-AM335X: "gmake: *** No rule to make target" error for PDK...
Part Number:PROCESSOR-SDK-AM335XTool/software: Code Composer StudioHello,I'm trying to build the PDK example projects for a Beaglebone Black using CCS Version 8.2.0.00007 on Windows. The PDK is...
View ArticleRTOS/CC3220S-LAUNCHXL: CC3220S-LAUNCHXL: Using ADC pins as GPIO pin.
Part Number:CC3220S-LAUNCHXLTool/software: TI-RTOSHello everyone,I am having some trouble configuring the adc input pins to function as gpio pins using the CC3220S launchpad. I can't get pin 57 to pin...
View ArticleTMS320F28069: Instaspin at low RMP
Part Number:TMS320F28069Team, My customer is having trouble in getting the AC induction motor to start and run smoothly at low RPMs (<500) using Instaspin dev board. There is a lot of torque...
View Article