Output frequency LMX2582, TICS pro
iI have a question about configuring LMX2582. The chip is palced on the evaluation board ADC32RF80EVM and I try to get 3GHz from LMX2582 outputs. His input frequency = 122.88MHz (get from LMK04828). I...
View ArticleCC1350: Low Radio Coverage cc1350sensorTag-Contiki 3.0-6LowPan-6lbr
Part Number:CC1350Dear all,I did a communication between two devices:1.slip-radio(Launchpad cc1350)2.Radio Node(Sensortag cc1350)3.BBB connected to Slip-radioI noticed that despite I put nullrdc_driver...
View ArticleClik here to view.
WEBENCH® Tools/TPS62740: Input transient simulation 'panel' has not...
Part Number:TPS62740Tool/software: WEBENCH® Design ToolsI made some changes to the simulation basic parameters, Vin and Vout, changed Vin to 2.5 V - 4.5 V, Vout to 2.2, and selected 'Input Transient',...
View ArticleClik here to view.
CCS/LAUNCHXL-CC1310: LAUNCHXL-CC1310
Part Number:LAUNCHXL-CC1310Tool/software: Code Composer StudioWhen i build project "cc26xx-demo (example of contiki os)" using LAUNCHXL-CC1310 SimpleLink™ MCU LaunchPad, it successfully build and...
View ArticleCompiler/CC2640R2F: Sending Measurement Data over BLE
Part Number:CC2640R2FTool/software: TI C/C++ CompilerDear allI success sending ADC over BLE on Mobile Phone.But on Mobile Phone ADC value is Hex How do I change the value as same as Terminal?Should I...
View ArticleIWR1642: mmWave SDK message output information (rangeIdx and angle)
Part Number:IWR1642Hi,Two questions:1. rangeIdx: can you give me more detail information for this? I checked...
View ArticleLinux/AM5728: USB Interface
Part Number:AM5728Tool/software: LinuxHi Can some one please help me how to use USB interface in AM5728 EVM as device mode to communicate with the other end processor(4G module sierra wireless) which...
View ArticleDRV10983-Q1: considering parts DRV10983Z, but max junction temperature is 150'C,
Part Number:DRV10983-Q1What does TI recommend for three phase brushless dc motors above 125'C to maximum of 150'C(operational)?considering parts DRV10974 but this is 125'C maxconsidering parts...
View ArticleBQ2000: Supply range
Part Number:BQ2000Hallo TI,I wanted to use BQ2000 Battery charger for charging 3 Ni-MH cells in series. In datasheet says, input supply range is between 4 ot 6V and in EVM datasheet says it requires...
View ArticleClik here to view.
UCC28070: why current synthesizer has output A and output B?
Part Number:UCC28070Hi, From my perspective, the PFC controller only need to get the information of input current, input voltage and output voltage.The reference of input current should be the same...
View ArticleADS8588S: Source Code
Part Number:ADS8588SHi Dale Li,Could you also share the C code source for the ADS8588S ?Best regardsPat
View ArticleClik here to view.
AWR1642: AWR1642 SLB
Part Number:AWR1642hi；I want to apply the slb project to implement the reload function, but I can't build the project.1.Can I provide a project that can be run or a project that can be imported?2.If...
View ArticleTCAN1042-Q1: Max Values of Some Switching Parameters
Part Number:TCAN1042-Q1Hello,I need the Max values of some switching parameters of TCAN1042-Q1 (TCAN1042DRQ1). Then, I took a look at this e2e post TCAN1042H: Driver/Receiver Switching Characteristics...
View ArticleWEBENCH® Tools/LM25037: Not in WEBENCH
Part Number:LM25037Tool/software: WEBENCH® Design ToolsHi, I'm curious why the LM25037 isn't offered in WEBENCH.Is there a spread sheet or any other aid to help design this part into a...
View ArticleLinux/WL1837MOD: BT-PCM integration to a custom board + Wilink8 sound driver
Part Number:WL1837MODTool/software: LinuxHello everyone,I have an custom board based on imx6ul and a wl1837 Wi-Fi/Bluetooth module and I would like to use Bluetooth HFP profile.I understand that i need...
View ArticleINA188: The output voltage is lower than the input voltage. Also the signal...
Part Number:INA188Daer allI use amplifier for very low input voltage values. I work with a range from 0.4 to 20 mV. Gain = 1. I use an amplifier for amplify the current. At the lowest voltages from 0.4...
View ArticleClik here to view.
SMARTRF06EBK: cc2538 SPI MISO pin receives 0x00 in variable
Part Number:SMARTRF06EBKHello,I am working on cc2538 SPI as master and my slave is an EEPROM chip. I can see the MISO receiving data on Logic Analyzer, but the variable in code that receives data shows...
View ArticleClik here to view.
LMR14030: LMR14030 simualtion results not satisfactory.
Part Number:LMR14030My input specifications are.1. Generate a 5V +/- 3% output voltage ; output ripple~50mV or less if deemed necessary2. Nominal operating range 9-16V3. Output...
View ArticleClik here to view.
RTOS/AM5728: Useing VPS to capture discrete 12-bits monochrome image
Part Number:AM5728Tool/software: TI-RTOSHiI'm using am5728 to capture 12-bits monochrome images from ar0135cs via vin2a. i just want to gat the original 12-bits raw data without any convertation....
View ArticleClik here to view.
MAX3243: Maximum Output driver voltage
Part Number:MAX3243Hi E2E,I read RS-232 application and find out the output driver voltage is +/- 15V Maximium.http://www.ti.com/lit/an/snla037b/snla037b.pdfWhy is MAX3243's SPEC just only +/- 13.2V?
View Article