BQ25601: MT6737 kernel-3.18 platform for BQ25601
Part Number:BQ25601Dear Ti sirCould you have BQ25601 driver for MT6737 kernel-3.18 platform ?
View ArticleClik here to view.
AM5728: pin mux tool for enabling GPIO pins
Part Number:AM5728Hai,i am using AM5728 GP EVM board. I tried to use pin mux tool for this board and generate code for GPIO5_11 and GPIO5_12, but instead there is no code generated when the pins are...
View ArticleTIDM-WIRELESS-MICROPHONE: Question and Support
Part Number:TIDM-WIRELESS-MICROPHONEHiOne customer interested in the TIDM and have following questions.1. Does the reference design available for loan?2. What is the audio latency of this wireless mic...
View ArticleCC2640R2F: LaunchpadR2
Part Number:CC2640R2FHi all, I am using simple peripheral code from ble5 stack examples and I want to change default phy setting to coded in the code so that when i power off and reconnect it will...
View ArticleRTOS/AM5708: Problem with eCAP as APWM in DSP
Part Number:AM5708Tool/software: TI-RTOSHello,We want to configure the ECAP1 as PWM from DSP in AM5708, but it doesnn't work when RT-Linux is running on A15.Wee see a square wave but with changing...
View ArticleLinux/AMIC110: PRU-ICSS Ethernet support on Linux
Part Number:AMIC110Tool/software: LinuxHi Team, Can AMIC110 support the Standard Ethernet(TCP/IP) on PRU-ICSS unit on Linux? Thanks and Best regards, Kuerbis
View ArticleUCC28063A: what if the switching frequency is over 500kHz?
Part Number:UCC28063AI found that the switching frequency is limited to 500kHz for UCC28063A on the introduction page...
View ArticleClik here to view.
CCS/CC3220SF-LAUNCHXL: PCB Board UART Communication - Unflash Connect issue
Part Number:CC3220SF-LAUNCHXLTool/software: Code Composer StudioHai, have a custom designed PCB based on the CC3220SF and i can not communicate uniflash and Debug We have not been able to flash our...
View ArticleCCS/MSP430F5529: Hi-z state of port pin
Part Number:MSP430F5529Tool/software: Code Composer StudioHi guys,I have a question regarding the Hi-z state of micro controller pins.My question is can i make my port pin to behave as HIGH, LOW and...
View ArticleTPS61240: Start up issues into 18ohm static load
Part Number:TPS61240I'm wondering if the device can startup with a 18R load on it? There is a Figure 18 in the datasheet which is referenced as "Startup after Enable, Vin = 3.6 V, Vout = 5 V, Load =...
View ArticleClik here to view.
What resistor value should i use for EN pin pull up?
Part Number:TPS2557Dear Sir/Madam,I would like to check with you on resister value using at EN pin and FAULT pin.Based on IC specification is using 100Kohm but EVM using 10KohmCircuit from IC...
View ArticleTAS2505: Speaker output seems to get disabled when trying to configure AINL/R...
Part Number:TAS2505Hi, I am trying to configure the TAS2505 amplifier according to the 4.0.9 setup example (slau472 Application Note.pdf), but the output on the speakers do not have any PWM-output...
View ArticleLAUNCHXL-F28379D: 3d model needed
Part Number:LAUNCHXL-F28379DHello,is there a 3d model of the LAUNCHXL-F28379D version V1.2 and V2.0? If anyone has a model of a similar version with nearly the same appearance it would be fine...
View ArticleADS7828: Reduced SCL frequency
Part Number:ADS7828HelloFor a temperature monitoring application we may have to reduce the clock frequency of the i2c bus (because of the "long" distance between the slaves). Does the ADS7828 support a...
View ArticleTPS759: PowerPAD connection
Part Number:TPS759Hi,We are using TPS75933 LDO regulator in our design.Please let me know we should I connect the power pad pin of the LDO.Can I connect the power pad to Ground?
View ArticleTINA / Spice / DAC0800: Spice model for legacy devices
Part Number:DAC0800Tool/software:Модели Tina-TIили Spicehi,i do project at MULTISIM and i need SPICE model DAC08
View ArticleClik here to view.
TIDM-1000: Eval board starting questions
Part Number:TIDM-1000Hello everyone,This thread follows my previous about tidm-1000 first launch. I have multiple questions :1/ What is the link between the .c code and the "kit.xml" ? I have...
View ArticleLDC0851: Sensor cap placement
Part Number:LDC0851Hi, I don't understand why the datasheet states that I need to place the sensor cap close to the IC. Why do I need to do this?
View ArticleRTOS/CC2538: IEEE address is differnet in SMART RF flash programmer and...
Part Number:CC2538Tool/software: TI-RTOSHello All,We are using CC2538SF23 as coordinator.We are using CC2538SF23.icf provided by following threade2e.ti.com/.../372137When we read IEEE address of...
View Article