Clik here to view.
ADS1118EVM SPI config register
Hello,I'm having trouble setting the configuration register on the ADS1118EVM using SPI. I've tried various combinations of Continuous/Single-Shot and samples per second, but haven't had any luck yet....
View ArticleAM3894 / DM816x Board is not running ; CCS output
I have taken sample uart loop code from DM816x/AM3894 Eval Board package. Built with CCS and output file i have programmed on the NAND. Added GP header in the binary file; relocation address i have...
View ArticleTimer Interrupt with LPM3, Debugger problem?
Hello,I am trying to run a timer interrupt and go back into LPM3. I run into a problem where my code works when debugger is running, but when I "unlink" debugger it stops working.What happens is when...
View Article10-bit calibration result
Hi,In page 696 of TRM (spnu499), "19.8.1.2 Calibration and Offset Error Correction Sequences" is described.I want to use this calibration function and get the 10-bit calibration result.In case that the...
View ArticleMid-Point Calibration detailed flow chart and sample code
Hi,I want to use the Mid-Point Calibration function on TMS570LS2125 and get the detailed flow chart and sample code.I know that the summary of the Mid-Point Calibration function is described in...
View ArticleWhat is STR?
Hi,In "7.6.1 Example1" and "7.6.2 Example2" of TRM (SPNU499),"(e) Resume the Test if required using Program Control register (offset = 0x16C) STR = 2." is described.However, I can't find STR...
View ArticleClik here to view.
Help needed to debug LMP91000SDEVAL board problem
hai,We are using LMP91000 development board for past 8 months and experiencing the following problem for the first time. It was working fine till last Friday (8 march 2013). While i was acquiring data...
View Articleusing uart of cc2540
Hi,I am trying to send data from msp430 to cc2540 keyfob via uart.just for test, in msp430 i set baud rate as 115200 with no parity and 1 stop bit, and send a number increment from 1 every second.and i...
View ArticleDRV8301-69M-KIT
Greetings:Does the XDS100v2 come with this kit, or must it be purchased separately?Thanks
View ArticleHow to debug m3vpss hang-up issue?
hi,we are tring to intergrate one sensor onto the 8127 IPNC platform. The sensor output is 10-bit bayer parallel(720P). My IPNC version is Beta Release Version 2.8. I have setup a very simple test case...
View ArticleADS58C28 and TSW1400
Is it possible to capture samples from the ADS58C28 with the TSW1400?Thanks,Jeremy
View ArticleTI ARM tool chain compiled H.264 codec for DM368
Dear all,We are currently considering development of an industrial video recorder. Since it has to be able to boot up in about 5 seconds, we don't think Linux is suitable OS for it.So we are...
View Articleam335x how to set gpio in linux kernel
Hi deari'm using {"mcasp0_ahclkx.gpio3_21", OMAP_MUX_MODE7 | AM33XX_PIN_OUTPUT},to turn on my LCD.i want to set gpio3_21 to high in kernel. i find the functionvoid omap_mux_write(struct...
View ArticleLMH0302
We are using LMH0302 in our design. We have the following query :If input is HD but LMH0302 is configured as SD, will it damage the IC? (I understand that we will get a corrupted output due to...
View ArticleAbout user-supplied ROI in DM365
Dear all,I followed the indications on "Smart Codec features in DM365 user guide" about using the Region Of Interest feature on DM365. In particular I changed the following...
View ArticleLM21212-2 Simulation Error
We are using LM21212-2 Synchronous Buck regulator (5V to 3.3V @3.047A) in our design. I am doing the Point of Load Analysis for that regulator using TI’s WEBENCH simulation tool. When doing the...
View Article"Could not open file" error on stellaris with ccsv5
hii m new to stellaris and ccs platform..when i try to run the sample code i got the error as belowi m using LM4F232H5QD evaluation board..CORTEX_M4_0: GEL Output: Memory Map Initialization...
View ArticleHelp for PGA400
Hi,I am using PGA400, I am new for this device, I need basic information about this device.1. how to program this device.2. which IDE to use.3. Is sample project are available for this device.
View ArticleMSP430G2232 power supply problems
Hi, collegues.I have a question regarding MSO430G2232 power supply. It's nessesary to work with 2.3 V supply voltage. But, after setting 2.3V or lower, the unit either reboot or suspend.I tried 12 MHz...
View Article[AM3359 Wince7][BSP_WINCE_ARM_A8_02_30_00]H27S2G8F2C support
Dear all,I am useing BSP_WINCE_ARM_A8_02_30_00 bsp code in AM3359 wince7 platform. and I want support Hynix "H27S2G8F2C" 256MB SLC .So I modified below code: Bspcfg.c...
View Article