Clik here to view.
PxSEL2 Register Settings Documentation for G2553?
I am working with the G2553 device in the Launchpad and am having trouble locating the register setting values for PxSEL2. I have found in the Family User Guide the following table which essentially...
View ArticleCC3000 API and RTOS
High, I am studying CC3000 API. There are clearly blocking function such as "select". I am thus wondering whether a RTOS is needed or not for this API to work.Is a RTOS needed ? Could a cooperative...
View ArticleLaunchpad P1.3 Voltage Problem
I'm using a MSP430G2553 for a sumo robot. I currently am using P1.3 as a GPIO pin to drive motors via a L298N motor controller. I have four GPIO pins in total that I am using for this, and they work...
View ArticleTimer A1,LPM3 and JTAG
Hi,I'm working with MSP430F5338 and MSP-TS430PZ100C as evaluation board. I run into the following problem:- By timer A1 CCR0,i've define the sleep_interval and with timer A1 ISR on TA1IV i've wake...
View ArticleNeed to choose a MSP430 with the following configuration
Planning to develop an application , I need two rs-232 ports and one rs-485 ports for my application .... Please help ... Also suggest if any other TI mcu could serve the purpose ?Also mention if some...
View ArticleMSP430 Reducing Power Consumption / Clocks / WDT
Hi allI am quite new to the MSP430 and want to clarify a few things.I am using a TI Lanchpad rev 1.5 with a custom breakout board featuring a sensor linked via I^2C and a wireless RF module linked via...
View Articleusing SPI in the EVM
hi,i have the EVM with the touch screen.i'm using SDK 05.05.00.00.when i'm starting u-boot i want to use the comand to connect SPI to the NOR flash.this is the line i want to run: sf probe 0x0and this...
View Articlesend() not actually sending
Hello all,I am attempting to get my CC300 to send a small bit of data to a linux box. I know my CC3000 is connected to my AP because I can ping it. I also know that it is opening up a connection with...
View Articlevxworks through spi
hello,i managed to start the EVM with u-boot through spi and the NOR flash. with the help of this (http://e2e.ti.com/support/arm/sitara_arm/f/791/t/246353.aspx)now i want to do it with vxworks boot.in...
View ArticleDaisy chained Ethernet
Hi all,We are developing on a custom board consisting of several C6678 DSPs divided into pairs. Of each pair, one is directly connected to a Marvell network switch via SGMII and the other is...
View ArticleTI Deals Site is Down
Dear All, I am trying to open TI deals site from past 3 months but its Down.Its offering many great deals.....When its going to work again and what is problem with TI Deals ? I waiting for...
View ArticleCurrent Sensing using INA118
Hi,I am trying to measure the current on high side using a shunt resistance. During certain stages, the voltage across the shunt resistance could go as low as 60uV. So, I chose the INA118. The gain I...
View ArticleMSP430 Internal Flash memory...General questions
Hi everyone,I have a couple of questions regarding the internal flash memory of MSP430:1- To my knowledge, a cell in internal flash memory can hold only one bit. Am I right?2- According to the...
View ArticlehelloDSP
Im trying to run helloDSP project on the OMAP L138.dsplinkk.ko was loaded well but application reterned follow messages========== Sample Application : helloDSP ==========Entered helloDSP_Create...
View ArticleUnable to run sample projects
Hello,I have an MSP430 Launchpad and am unable to run some of the sample projects. After building the project, writing the code to the MSP430 and entering debug mode, I receive the following error...
View ArticleProblem in running FDK Fingerprint example on TMS320C5515 board
I'm using TMS320C5515 and try to run the FDK_DEMO application.In the module TA_hal_sccb.c, in line 248, the following statement:while (!VSYNC); get to infinit loop. The polled signal is the bit 22...
View ArticleClik here to view.
help:confused on cortex m4 board
hi everyone i am looking forward to purchase evaluation board for learning cortex m4. i would be requiring GLCD/TFT and camera in future for some image processing applications where i might be using...
View ArticleCompiler switch for DSK6713?
i m confused in a compiler option setting.....in some book it is written to take -mv6700 in text box of target version and in some case it is written to take or choose -mv6701....i m using DSK6713...
View ArticleADS1274-EVM
Hello,I'm trying to develop some firmware for an ADS1274. I currently have the ADS1274-EVM, an MMB0 modular motherboard, and a C6748 LCDK (the target CPU for the firmware). Is it possible to use the...
View ArticleUsing ILI9341 LCD controller with Stellaris graphic library
Hi there, So I used the provided header file by TI (kitronix320x240x16_ssd2119_8bit.h) with LM3S9d96 uc and was able to use the graphic library including the widgets w/o any problem. Though, the new...
View Article