Delfino F28377D controlCARD (TMDSCNCD28377D)
Hello Everyone,I'm a new user in Delfino processor and trying to use Delfino F28377 control card for PWM out from pin 49. We are using a program written in C++.The program is sometines works and get...
View ArticleIs there need capacitor between VCC-GND of TL7700？
Dear support member,Is there need capacitor between VCC-GND of TL7700？The capacitor was not described of data sheetbut, the Fig14 of application notes (SLVAE04) had been described Cb is.If there...
View ArticleHow to discard the current frame in the capture link data?
dm8168, dvrrdk 4.0Since the acquisition of the front end of the problem, after the front end of the camera off, or can be collected to the wrong resolution video frame; I can read out the information...
View ArticleESD strick to OMAP-L137 w/ SDRAM
Hello,I use OMAP-L137 with a external clock source and a 32-bit SDRAM. It seems that our system is susceptible to radiated noise during an ESD strike. L137 is uncontrolled during an ESD strike when the...
View ArticleMax number of client support CC3100 AP mode
Hi~I set CC3100 in AP mode.I can use a device connected it.but now, I want two or more device connected it.so how can I to do?How much device can connected it at same time.Nash
View ArticleADC08D1520RB does not respond to signal fed in
Description:ADC08D1520RB is unable to digitize the sine wave fed in and only noise is observed on WaveVision. The sine signal frequency is 100MHz and level is -1dBm and -2dBm.over_range LED flash is...
View ArticleP82B96 Qestion of Datashet page16
HiP82B96Data seat (SCPS144B) the numerical value from where is the number indicated on Page16?(When what do you refer to, this, can the numerical value be understood?)Below is its numerical value.....
View ArticleDS90UB947-Q1 with Jacinto6
Hello,I think that we can't use the DS90UB947-Q1 with the Jacinto 6 due to the Jacinto 6 don't have open LDI interface.The Jacinto 6 have Parallel interface only for display interface.Are there any...
View Articlesuccessful join but link failed
Hi Allmy platform is TM4C129+CC1200,I have done the simple peer-to-peer communication,and now I try the AP star network,I just use one AP and one ED, and the ED program works very well(has been...
View ArticleProblem with ADC triggered by PWM in TM4C1294
Hello people.I search a lot in the forum and in the internet, but I don't a solution to my problem. I need to trigger the ADC with the PWM, but the code that I developed to do this, don't work! Get...
View Articlecc26xx Bootloader communication
I am study in TI new product CC2650 (QFN48/7x7) and have some question about Bootloader Functionality For Update valid image.I use SmartRF06 Evaluation Board + CC2650EM-7IDI would communicate with an...
View ArticleBLE_Bridge: simpleProfileChangeCB()
Dear all:I can not find where to call the function simpleProfileChangeCB() in BLE_Bridge project.Can someone help me?B.R.KJ
View ArticleLMG5200 DC-DC Boost Design [M] NE
I'd like to use the LMG5200 in a dc-dc BOOST configuration, 12VDC from a POLA for VIN to 30VDC 4A output. The LMG5200EVM User Guide states that it can be used in this configuration, but I am not...
View ArticleChanging booting (entry) point of cc3200 ti-rtos application in IAR
HiI am working on cc3200 with code composer studio IDE, To check the code size optimization on different compilers I ported my application to IAR and compiled it successfully.Requirement: We are using...
View ArticleCC2650STK sensors sampling rate
Hi Can anybody help me to increase sampling rate of sensors on CC2650STK?The maximum sampling rate is now 10.Thanks
View ArticleF28035 piccolo control Estun EMJ-04APB22 settings
Dear Hank:Hello, I want to ask that the settings in my "HVPM_Sensored_Servo.h" with " Estun_EMJ_04APB22"Servo PMSM.I found this website:...
View ArticleDM814x write to INIT_PRIORITY_0
I'm trying to change the setting of INIT_PRIORITY_0.I don't seen to be able to access correctly. See that attached console log. The inserts in () are comments I added later.(read...
View ArticleLoading a BMP image into the LightCrafter 4500
Hi - I just received the LightCrafter 4500 and installed the GUI. I'd like to display a 912 x 1140 BMP image (dot-to-dot), by loading it into flash memory, pattern sequence mode. According to the...
View ArticleDMA UART Transfer (MSP430F5529 Launchpad)
Hi,I´m trying to send a 240bytes Buffer via UART using DMA, and i have some problems that i dont understand, if i set the DMA for sending just "one block" the serial port on PC doesn´t recognize any...
View ArticleDMA McBSP stall problem in Delfino
I'm putting the polish on a Delfino-based measurement system developed under CCS and SYS/BIOS, and have come up with an unexplained DMA stall when linking the McBSP (configured as a clock-stop SPI...
View Article