Document request - Antenna SensorTag and RF matching networks
Hi, I am developing an device and I am studing some microcontrollers for my project. We have much interest at CC2640 for our applicantion. Our expectation is to produce 1000 devices/month and CC2640...
View ArticleTPS61197 multi-chip operation parallel
Dear Sir,Just a question about TPS61197. Can TPS61197 like TPS61196 parallel operation ?TKS!
View ArticleHow can i get the software MSPMATHLAB？
win7 32-bit ,ccsv6.I visited http://www.ti.com/tool/mspmathlib ,then i pressed the button "get software",it linked to another website http://www.ti.com/tool/ccstudio ,but i could find nowhere to...
View ArticleEnd Customer is interested in using Wl183X for Access Point product --- what...
Our End Customer is interested in using Wl183X for WiFi Access Point product --- what is the number of simultaneous WiFi clients supported in AP or STA mode ? Is this supported via hardware or...
View ArticleClik here to view.
DRV594 Heating mode operation
Hi,I'm trying to understand how the DRV594 works in Heating mode.According to the datasheet, the output voltage will increase (in the -ve direction, hence more heating) as the differential input...
View ArticleUART receive causing knl.Clock assert?
I am using the UART at 115KB and have added additional code to be processed in my foreground loop (1ms ISR).It ran fine with and without using a UART ISR. But the latest code stops receiving data.2...
View ArticleQuestion about McBsp's DMA configuration
Hi all, In my applicaton, I sample data via Mcbsp and DMA, 2 channels on Mcbsp RX , 16 word/ channel, data is stored in Uint16 A[2048] as following A[0] --ch1A[1] -- ch2A[2] --ch1A[3] -...
View ArticlePCIe enumeration?
H experts,I have one question about PCIe enumeration.Our system is Host CPU.PCIe -------------------- PCIe Bridge or Switch ---------------- Keystone1 PCI or KS2 PCIeWhen all the 3 devices are...
View ArticleSVC encoder support on DM8127 IPNC RDK 3.8
Hi,In the Product_Datasheet_IPNC_DM8127.pdf, it is written that "Supports SVC-T mode of encoding for H264 Codecs". How to enable SVC encoder in IPNC RDK 3.8? Thanks,Vijay Patel
View ArticleLoad program into the TMS320F28377D
Hello all,I have a TMS320F28377D and i have a evaluation board with it. This evaluation board and have a xds200 spectrum digital emulator with it. When i turn off my board and turn it back on the...
View ArticleLinker file: Flash API and FEE
Hi, I am using the TMS570LS1224, Halcogen 4.3, CCS6 and Flash API 2.1.1. I am writing a bootloader, and already have FEE set up in the linker and can properly write and read data. I tried to add the...
View ArticleBreakout board development for Microsemi FPGAs
I just received my TI ads6142EVM-CB evaluation module and breakout board. We are using Microsemi FPGAs so there is no breakout board available (like for Xilinx, Altera) that allows differential pin...
View ArticleClik here to view.
DM8107 , problem size display on VOUT0
Hi,I use the DVRRDK 04.01.00.02 on a custom board with a DM8107I try ti display video on VOUT0 port.I finally managed to get a video stream on the output of the DM8107 VOUT0 making several changes in...
View ArticleeCAP functionality
I have the sine and cosine signal of a speed sensor connected to GPIO-32 and 34 of the F28069M MCU. The signals consist of 16 pulses each (8 rising, 8 falling), and I need to get the speed from these...
View Articlewhat is UC0CLK in MSP430G2553 (USCI_A0) UART mode ?where is UC0CLK clock...
In MSP430G2xxx family (MSP430G2553) USCI_A0,when selecting the clocks for the USCI_A0 in UART mode there is an option for UC0CLK.Where does UC0CLK comes from?.
View ArticleTAS5708 DRC not responding
Hello,I've tried to set the DRC with the following settings:gain: 0 (O = 0.064516 = 0x00084210)threshold: -64 (T = 14.616484 = 0x074ee8f0)ratio 30:1 (k = -0.966667 = 0x03844445)attack, release and...
View ArticleLMX2581EVM OscIn Power Levels
I am evaluating the LMX2581EVM and I was wondering if I could clock the device with an external 10 MHz Wenzel oscillator spec'd for +13 dBm output. My real question is, is there a specific power level...
View ArticleClik here to view.
MSP430G2955 glitch on all outputs
Hello, just wondering if anyone as come across this before, all my outputs seem to be glitching together (green UART, Pink & Purp Debug IO lines).I ruled out this being a glitch picked up by the...
View ArticleClik here to view.
SN65LVPE502A / redrive two Tx signal of CPU
Hi Team,My customer considers to use SN65LVPE502A as the following figure.His board space is restricted and can't put two SN65LVPE502As, so he would like to redrive Tx signal of CPU only.Is it possible...
View ArticleHow to set P3DIR for UCAxRXD, UCAxRTD pins on MSP430F249?
I need to enable the UCA1RXD and UCA1TXD functions on the P3.7 and P3.6 pins of an MSP430F249. Clearly, I should set the bits 6 and 7 of P3SEL.How should I set the P3DIR bits, though? I ask because...
View Article