Quantcast
Channel: Forums - Recent Threads
Browsing all 262198 articles
Browse latest View live

Use Simplelink host driver on a non-TI MCU

Hi All,I have a question: is it legal to port and use the Simplelink host driver to a non-TI MCU that is connected to a CC3100MOD ? I would guess it is legal, from the license text at the beginning of...

View Article


Image may be NSFW.
Clik here to view.

sl_start(0,0,0) stuck

We are currently porting our CC3000 code to CC3100. In order to verify the HW and SW we connected a CC3100BOOST to our device and removed the CC3000 from our device.We observe now that after nHIB goes...

View Article


Getting IP address

i connect my cc3100 to a LAN induced by an access point  as a lan station and i wish to know what is its IP address?how is this acomplished?thanks,Yuri.

View Article

Not getting profiling data of Ti lib

Hi,I'm using CCS 5.5.0.00077 and try to start doing profiling on a small application using dsplib (3.4.0.0)Setting up profiling and getting data works fine, except that I don't get any data for time...

View Article

Black Vector Missing

Hi, I'm using the DLP 4500 over HDMI and want to load a pattern over it.  I set the resolution to 912x1140 and I followed the discription from the Evaluation Module. But every time I want to validate...

View Article


WL1831 AP Configuration Error

Hi,       When I tried to configure as AP through application, sometimes I am getting following error.=================================================wlcore: PHY firmware version: Rev...

View Article

UCD9081* PROGRAMMING OUTPUT

USING UCD9081EVM, we cant change/control  output voltages .Where can be the problem?

View Article

#include not found in project with separate config project

Hi all,I already posted a question in the TI/RTOS forum, because I thought it is related to my TI/RTOS configuration:http://e2e.ti.com/support/embedded/tirtos/f/355/p/402711/1436673#1436673Sasha...

View Article


UCD9222 VID's during Power Up

I have used the UCD9222 and UCD7242 in a design like the TI Eval TMDSEVM6657.During the verification of the power supplies, i have found the following:The POR (Power On Reset) time for the UCD9222 is...

View Article


multicore navigator

Hi,i'm using ccs version 5.4 and installed mcsdk and other packages also.i saw the multicore examples in pdk c6670 in that folder having many separated modules like...

View Article

F28069 control card connection problem

I have brought this F28069 control card (part no. TMDSCNCD28069). I am connecting this via XDS100V2 emulator but JTAG integrity test has failed and I am not able to connect this card. Anything I must...

View Article

Image may be NSFW.
Clik here to view.

Question about Breakpoint ->Action ->Read Data From File

Hi All,I use CCSv5.2 and TMS320C6678. I tried to use breakpoint with Action Read Data From file. My breakpoint properties isMemory state beforeMemory state afterArray isAttemp read writing fileOpen...

View Article

TPS7A6333-Q1 / connect the nRST pin with the WD_FLT pin

Hello,Can I connect the nRST pin with the WD_FLT pin ?I would like to use both pins for reset signal.Best Regards,Ryuji Asaka

View Article


Debugging problem

Hi Emmanuel,sorry for opening a new thread. It was not possible to add this final comment to that thread. It does not seem to be necessary to recreate the whole timer. I created a one-shot  timer in my...

View Article

TPS2492

We use TI's Hot Swap controller, p/n: TPS2492PW in our design.Attached is a section of the front end circuit which includes the HS controller.We do not assemble the following components: C4, C10,...

View Article


About DLP LightCrafter 9000 EVM

Hi, I would like to know can the DLP support 100K Hz signal using IIC( I²C) communicate with MCU? If it can't, what maximum volume can it support. Thanks for answering.

View Article

INA826 MAXIMUM Input voltage range

INA826 Datasheet Version SBOS562E –AUGUST 2011–REVISED APRIL 2013 have MAXIMUM Input voltage range as (–VS) – 40 to (+VS) + 40 V, and max typical use of +/- 40V.I'd like to use INA826 in 0(V-) and +36V...

View Article


Limiting data rate based on RSSI?

We are developing a new product that transfers signal data using the CC1200.  We were planning on limiting the speed at which we transfer this signal data based on the RSSI values.  For example, if we...

View Article

Image may be NSFW.
Clik here to view.

Problem with UCC27210

I am trying to use the UCC27210 to drive mosfets for a high power regenerative solenoid driver.The solenoid is between the high and low side mosfets, with flyback diodes to allow for the regenerative...

View Article

Using variables in Pre/Post-build steps in CCS v6

Hello,in CCS v5 it was possible to use variables containing semicolons within Pre-/Post-build steps.Example Post-build step:postbuildstep.cmd "${XDCPATH}"I think in CCS v6 the semicolon is used to...

View Article
Browsing all 262198 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>