CC2541: GPIO Default output status issue
Part Number:CC2541hi TeamWhich I/O can be configured to output low when the CC2542 powered on?Thanks
View ArticleRM57L843: Bank 7 Programming - Fapi_doVerify failing in certain cases.
Part Number:RM57L843Hi,I've posted on this topic a year ago, I though it was solved, but its back.The symptom is defined such that: I can write a buffer stored in RAM to FLASH Bank 7 using the Fapi....
View ArticleClik here to view.
TPS763-Q1: Why TPS763-Q1 requires some more ESR compared to other devices?
Part Number:TPS763-Q1Hi,Currently I got a question from customer that TPS763-Q1 datasheet mentioned 0.3-10 ESR is needed for a 4.7uF Output capacitor. I checked our part with Rohm's BU33SD2MG(currently...
View ArticleRTOS/CC2642R: How to set counter timer
Part Number:CC2642RTool/software: TI-RTOSHello,Im using CC26x2 MCU with SDK 2.10.0.44.In my project I should connect sensor of gas rate and the data output given by pulse. IO want to count that pulse.I...
View ArticleBQ35100: Primary Lithium Sulfuryl Chloride Not Listed in the Battery...
Part Number:BQ35100Hello,I want to use the BQ35100 with primary cells from ELECTROCHEM. Specifically the "CSC93 SERIES: 3B0024" (see attached datasheet). The battery is not listed in the "Battery...
View ArticleClik here to view.
OPT8241: Need workable image for TIDUBL5A
Part Number:OPT8241Dear/Madam,I am following the instruction in TI Designs TIDUBL5A People Counting for Demand Controlled ventilation Using 3D Time-of-Flight (ToF) reference design. But I am not able...
View ArticleCC2531: Configure ZigBee client bind to send commands
Part Number:CC2531We have a number of devices that employ clients supporting the ON_OFF cluster and I'm trying to work out how to get these to generate a command when the respective button is pressed....
View ArticleMSP430G2744: Problem with UART IO at MSP430G2744
Part Number:MSP430G2744Hello!We have sensor that controlled by MSP430G2744. It connected to our microcontroller Nordic nRF52832 via UART via next 2 IOs: P3.5/UCA0RXD/UCA0SOMI &...
View ArticleClik here to view.
TMS320F28069: CLA acos to debug
Part Number:TMS320F28069Hello,I'm trying to debug run the C2000Ware CLA sample project "acos".Could you please advise how to debug-run the CLA code many times?It seemed to fail handshaking between the...
View ArticleTMS320F28377D: TZFLG[OST] and TZOSTFLG ,Which flag occurs earlier?
Part Number:TMS320F28377DHi,In spruhm8g.pdf ,page 1726, One-Shot (OSHT) section,It mentions that " Additionally, when a one-shot trip event occurs, the one-shot trip event flag (TZFLG[OST]) is set...
View ArticleLM5175: External Sync settling time
Part Number:LM5175I need to use external Sync of 250KHz and move to 255KHz. what would be the expected settling time to the new switching frequency?Dror
View ArticleTPA3131D2: Bulk capacitor value selection
Part Number:TPA3131D2Hello all,Regarding the value of the bulk capacitors required for PVCC:In the product's PDF it is mentioned that (page 22)"Select the bulk capacitors at the PVCC inputs for proper...
View ArticleTPS62170: troubleshooting and layout
Part Number:TPS62170Hi Chris,Alas, neither moving to TPS62160DSG nor changing the capacitance aided with preventing the failure at (minus) -50c degrees.Do you have any suggestions regading what could...
View ArticleDLP4500: Advantage of diamond pixel array
Part Number:DLP4500Hi everyone,I am a little confused about the pixel array of DLP 4500 now. Why does it adopt a diamond pixel array? What is the advantage of the diamond pixel array compared with the...
View ArticleClik here to view.
TMS320F28377D: eCAP module malfunction
Part Number:TMS320F28377DHi ,I use eCAP1,eCAP2,eCAP3 to detect the zero-crossing of 3-phase power supply system.Normally, the cap1, cap2, cap3, and cap4 values in the cap register are between...
View ArticleDRV8323: SPI interface always returns 0x0000 or 0xFFFF
Part Number:DRV8323Hi There, I had the same problem as a previously solved in an older post but in the solved post there was no description of what was done to solve the issue. Essentially I am writing...
View ArticleFDC2214EVM: Is it possible to connect/synchronize several EVM's to a computer...
Part Number:FDC2214EVMHello,I'd love to use four to five FDC2214EVM together to measure 16 channels at the same time. Is it possible to connect/synchronize several EVMs to a computer or a data logger?...
View ArticleCCS/MSP-EXP430FR6989: Turning Off EnergyTrace Switching supply and using the...
Part Number:MSP-EXP430FR6989Tool/software: Code Composer StudioI have a unique situation where the EnergyTrace switching regulator is actually causing noise on sensitive sensor lines of my project. I...
View ArticleDRV8711EVM: basic EVM bring up issues
Part Number:DRV8711EVMI'm trying to get my DRV8711EVM working. The D3 LED flashes, D2 never comes on. When I hit the Nsleep button, it turns green (not sure if that means anything), but D3 continues...
View ArticleLinux: how to enbale dsp c66x and load a .out file from linux running on...
Tool/software: LinuxHII use the board GP evm AM5728 , I want to run linux on cortex-A15 that enable dsp c66x and load a .out file to run it . Thanks,
View Article