DRV10975: Motor Heating Issues
Part Number:DRV10975Hello, I have a DRV10975 connected up as per the recommended values in the data sheet. It is driving a Maxon EC20 flat motor.The motor starts and maintains speed well, although...
View ArticleClik here to view.
BQ24259: Confirm ISYS problem
Part Number:BQ24259Dear TI sirBQ24259 Isys show 3.5A. Dose it mean BATFET Q4 ?
View ArticleTDA2: Vision SDK TDA2xx v03.02.00
Part Number:TDA2Hello everyone:Here are my environment:Hardware:1. TDA2xx EVM2. TDA2xx Vision Application Board 3. 6 channel FPD-Link III FMC Daughter Board4. 2 x OV10635 SensorSDK: Vision SDK 3.0.2I...
View ArticleTSC2046: Temperature measurement
Part Number:TSC2046We see sbas265g page 15 table3, and temperature measurement is availablein case Single-ended only.Customer had chosen TSC2046 for their portable equipment 2018 model ( Mass...
View ArticleBQ78350-R1: CEDVStatus() == 0x0056 GaugingStatus ?
Part Number:BQ78350-R1CEDVStatus () appears at sluubd3c.pdf in the following two places. p.59 9.1.2p.62 9.1.7 However, searching STD SBS, Extend SBS, Manufacturer Access, DF does not hit.Therefore, I...
View ArticleClik here to view.
CC1310: Battery Powered CC1310 Design
Part Number:CC1310Hi all,I have looked at a number of TI reference designs for applications involving a battery powered CC1310 sensor. In the reference schematics, all of them had a SI2323 connected to...
View ArticleTDA2xx Booting
Hello,Can you explain more specifically what will happen if the sysboot [5:0] are NOT set to one of the settings mentioned on the TRM Table 29-9.specifically what will be the behavior if they are all...
View ArticleUCC28180: UCC28180EVM-573, The Spec. of boost inductor，form NOVA MAGNETICS
Part Number:UCC28180Hello！ About the UCC28180EVM-573, there's a boost inductor L2 from NOVA MAGNETICS on page 22 of user guide, the part No. is 7840-09-0014，but I can't find the NOVA‘s web link, and I...
View ArticleDS100MB203: How to use FAN-out feature?
Part Number:DS100MB203Hi Team,DS100MB203 can support FAN-out feature refer datasheet.It means D_IN0 siganl go out to S_OUTA0 and S_OUTB0 togehter.However, I don't know how it is possible with SEL0/1...
View ArticleTAS5766M: the method of power stage shutdown
Part Number:TAS5766MHi,Does the power stage of TAS5766M shutdown if XSMT pin is asserted?Is there any way except XSMT assertion to shutdown TAS5766M power stage, although the power is supplying?Best...
View ArticleCCS/TMS320C6742: Could not open .cfg file in graphics configuration form!
Part Number:TMS320C6742Tool/software: Code Composer StudioHi, I have installed ccs7.3 and TI-RTOS kernel as shown below.TitleDescriptionSizeOMAPL138 RTOS SDK...
View ArticleCDCLVC1310: Bypass mode for the Crystal-oscillator input
Part Number:CDCLVC1310Hi team,I have a question about the bypass mode for the crystal-oscillator input.If I set the input clock select pin to 11, it means I choose the XTAL bypass mode.So it means I...
View ArticleCC2538: Debugging Memory Leak in ZNP / Z-Stack 3.0.1
Part Number:CC2538Recently we discovered that when restarting the Linux side of Gateway application which interfaces with ZNP many times it is possible to get the module to leak memory. This gets worse...
View ArticleTMS570LC4357: I/O multiplexing and Control Module default values after reset...
Part Number:TMS570LC4357Hello,I/O multiplexing and Control Module default values for eCAPx and eQEPX modules described in the TMS570LC4357 TRM are not inline with what is observed on target.Special...
View ArticleSN65C1168: SN65C1168 Schematics for Pin#:9(2D) and Pin#:15(1D)
Part Number:SN65C1168Hi team,Could you provide the schematics for pin#:9 (2D) and pin#:15 (1D) such as the schematic of inputs/outputs at page-4 in the datasheet?Thanks & Best regards,Jun Ishida
View ArticleLinux: Dual display configuration with Android O
Tool/software: LinuxHi sir,Based on the DRA74x EVM REV board, I want enable the Vout1 and Vout2 for LCD, if we used the HDMI port ,it can work fine, the system can show normally, but we want to used...
View ArticleWhere can I download the slides of TI training in OP session
Hello,I can only see the pdf file in op session page.https://training.ti.com/ti-precision-labs-op-amps-noise-2?cu=14685Could you please tell me where I can get these ppt files of Opamp for our...
View ArticleClik here to view.
CCS/IWR1642: JTAG Connection Error
Part Number:IWR1642Tool/software: Code Composer StudioHi,We made own design using IWR1642 device. We have some technical problems.We use XDS110 debug probe for connection to IWR1642 device.When we want...
View ArticleClik here to view.
CC3220: Uniflash does not recognize the FLASH chip
Part Number:CC3220Hi,Some time ago I posted a question on the forum about a FLASH chip that should work with the CC3220 but for some reason is not recognized by UNIFLASH.original thread:...
View ArticleClik here to view.
TPD13S523: TPD13S523-HDMI is not working
Part Number:TPD13S523We have received the prototype boards and observed that when TPD13S523 mounted in the board, HDMI is not working.When we removed this part from the board, HDMI interface works.HDMI...
View Article