Clik here to view.
Design the loop Power 24V for current 4-20mA analog input
Dear TI Engineers,can you advice me to design the loop power for analog input with 12 channel total number, it' mean analog input connected with 4-20 mA 2 wire system with system power (2 wire analog...
View ArticleLAUNCHXL-CC1352R1: 1 Mbps data rate with CC1352
Part Number:LAUNCHXL-CC1352R1Is the CC1352 capable of supporting a 128 byte transfer from one device to another (one way only, no ack needed) at a 1 KHz rate - basically about 1 Mbps data rate? But...
View ArticleCCSTUDIO-KEYSTONE: Keystone NETCP : SGMII interface with link interface...
Part Number:CCSTUDIO-KEYSTONEHi,I am using tci6638k2k processor in our custom board. There are two ports: port 0 (interface eth0) is connected to a PHY and we are using link-interface as MAC-PHY (mode...
View ArticleCCS/TM4C129ENCZAD: CCS8 does not see installed tm4c v2.1.3.156 product, even...
Part Number:TM4C129ENCZADTool/software: Code Composer StudioI installed Code Composer Studio 8 on macOS High Sierra 10.13.3, then used Resource Explorer. I was able to build one project and run...
View ArticleCC2650STK: CC2650 UART tx dropping bytes, corrupting output
Part Number:CC2650STKGood day -I'm using a cc2650 sensortag, along with the XDS110 debug probe (CC-DEVPACK-DEBUG). I'm developing a Contiki application and streaming output over the UART. I've observed...
View ArticleLMT70: Searching for cabled sensor probe making use of LMT70
Part Number:LMT70Hello,I am searching for a sensor probe making use of the LMT70 which employs a cable and attachment method similar to the following:...
View ArticleRTOS/LAUNCHXL-F28379D: LAUNCHXL-F28379D
Part Number:LAUNCHXL-F28379DTool/software:TI-RTOSDDear,I would like to try TI-RTOS with LAUNCHXL-F28379D board, Is there any TI-RTOS compatible software and any example?Thank you.SincerelySeong Chung
View ArticleDS125MB203: Cross switch/Buffer on 10Gbps SFI interface consultation
Part Number:DS125MB203Dear TI Engineers:We need a 1:2 switch or fan-out buffer using on 10G SFP transceiver.We find 3 TI chips as candidates, DS125MB203, DS100MB203, DS100MB201.Questions as below:1)...
View ArticleTINA/Spice/LM358: different behavior LM358 and LM358_101
Part Number:LM358Tool/software:TINA-TI or Spice ModelsHello,Our customer trying evaluation LM358PW with TINA-TI.They asked us which is correct model for them LM358 or LM358/101 and why the behavior is...
View ArticleClik here to view.
LM5018: The difference of efficiency between LM5018 and LM5019
Part Number:LM5018Hi Team,The datasheet shows efficiency of LM5018 is better than LM5019 under load current < 100mA. Left: LM5018, Right: LM5019On the other hand, Rdson is absolutely the same value...
View ArticleTMDSEVM3730: TMDSEVM3730, ISP1507BBS
Part Number:TMDSEVM3730Hi, Sirs,I have some questions about technical issue of USB transceiver on the TMDSEVM3730 board.On the board schematic, USB_OTG have two ways connection to the PMIC and CPUFirst...
View ArticleRTOS/CC2650: Using FlashProgram() function from driverlib in ROM
Part Number:CC2650Tool/software:TI-RTOSI'm trying to add FlashProgram() function call from driverlib to the example program that came with TIMAC SDK, which contains TI-RTOS 2.11. The compiled...
View ArticleTINA/Spice: Will TINA be available for Windows 10 soon?
Tool/software:TINA-TI or Spice ModelsHi, Will TINA-TI download be available for Windows 10 soon? In the downloads the latest windows listed is 8.Thanks, Mike
View ArticleDLPNIRNANOEVM: Scan Reference Selection
Part Number:DLPNIRNANOEVMOn power up , it appears that the default Scan Reference is factory. Is there a way to change this for a Scan Configuration, or where is this set.Is there an NNO_* command that...
View ArticleCCS/CC2640R2F: CC2640RF:We need check the max throuthput with BLE 5.0
Part Number:CC2640R2FTool/software: Code Composer StudioHello: Is there any test report for CC2640RF run with BLE5.0 to analysis of the max throuthput? We want get a max throuthput
View ArticleClik here to view.
LMK04828: pll1 cannot locked
Part Number:LMK04828hello, the schematic of lmk04828 is as follows, the PLL1 cannot locked, I calculated the loop bandwidth is 42.416Hz and the Phase margin is 15.782, should I modify the loop filter...
View ArticleClik here to view.
CC3220SF-LAUNCHXL: Custom PCB unable to connect to Uniflash via Launchpad...
Part Number:CC3220SF-LAUNCHXLHello,I currently have a custom designed PCB based on the CC3220SF-LAUNCHXL files and I cannot get it to communicate the Uniflash. I have UART TX and RX along with the...
View ArticleLinux/AM3352: AM335X UNIFLASH USB boot patch can't been download.
Part Number:AM3352Tool/software: LinuxHi all,The uniflash patch can't been download. Could you please help? thanks!http://processors.wiki.ti.com/index.php/Sitara_Uniflash_Flash_Programming_with_U-Boot...
View ArticleLAUNCHXL-CC1310: contiki mqtt client stuck in "Connecting..."
Part Number:LAUNCHXL-CC1310Hi,I have 6lbr (Router mode) running with RaspPi + CC1310 launchpad (slipradio). I got one more cc1310 launchpad into WSN. This end node is discovered and I am able to open...
View ArticleAM5728: vout2_clk signal of AM5728
Part Number:AM5728Hi,I have simple question regarding AM5728.Does AM5728 have the ability for changing the drive strength for vout2_clk" signal?I thnik AM5728 does not have such ability for any output...
View Article