TIDEP-0088: About "Adaptive Spectral Noise Reduction"
Part Number:TIDEP-0088Hi TI Experts,Would you please teach me about "Adaptive Spectral Noise Reduction"? Would you please explain about it?Best regards.Kaka
View ArticleCCS/IWR1443BOOST: IWR1443
Part Number:IWR1443BOOSTTool/software: Code Composer StudioHi, I'm asking that if the initial phase of every transmitted chirp is the same ? and how can I make them same when transmitting?Thank you...
View Articleselection of dsp
Dear sir,I want to design test and measurement instrument where m going to requied adc and fft, debugger.i m looking for the dsp starter board. is...
View ArticleIPC_FRAMES_OUT_FROM_A8 to HDVICP IPNC RDK3.9.1
Hi TI Experts,I'm working customized DM388 platform.I'm trying simple usecase Capture Display.In this Usecase From Cap to A8, I could able dump yuv frame without any issue by using call back function...
View ArticleBQ40Z50-R2: The alternative capacitor selection for PBI pin.
Part Number:BQ40Z50-R2Hi there,According to the BOM & schematic in user's guide, the capacitance of the capacitor connecting between PBI pin and signal-GND is 2.2uF and I'm following it for all the...
View ArticleCCS: what may cause the bit register "DEV_STAT 4" error?
Tool/software: Code Composer StudioI read the register of DEV_STAT 4 , the bits ABISTF and SFAULT were always set.I want to know , what reason may cause these two bits be 1 ?please help.thank you.
View ArticleUCC28180: Not stable Duty reason
Part Number:UCC28180Hi All,My customer is wondering why output pulse duty is not stable.Please give me advice.Attached : PFC waveform and cct.(Please visit the site to view this file)
View ArticleCCS/PGA411-Q1: what may cause the bits of register "DEV_STAT 4" error?
Part Number:PGA411-Q1Tool/software: Code Composer StudioI read the register of DEV_STAT 4 , the bits "ABISTF" and "SFAULT" were always set to 1.I want to know , what reason may cause these two...
View ArticleLM53603: Internal Parameters for Electrical Simulation
Part Number:LM53603My customer is very interested in the LM53603. They would like to simulate the device behavior by the simulation tool of the PLECS. Thus here are some questions.1. What's the VF...
View ArticleBQ24650: BQ24650 TS pin
Part Number:BQ24650hi if customer product have two power sources contain of solar panle and Li battery, so customer used BQ24650 and BQ24296M in the one board, and both of them have TS pin, my...
View ArticleTINA/Spice/ADS1248: Noise analysis
Part Number:ADS1248Tool/software:TINA-TI or Spice ModelsHi,I would like to ask you a basic question about noise simulation by using TINA-TI.There is an IBIS model of ADS1248 at TI web site.Is it...
View ArticleCC1310: Is there a BSDL file available for Production Board testing?
Part Number:CC1310Team,Do we have a BSDL file available for the CC1310? If yes what are the condition to share it?I did not find it on the TI web under "Tools and...
View ArticleLM339: Question about Pin assign
Part Number:LM339About LM339 (and the other general purpose OPAMP), please let me confirm about datasheet information. In the datasheet, pin assign: 8~11pin are different of page-4 and page-13. (IN+...
View ArticleClik here to view.
IWR1642BOOST: Can I get rid of the noise at Zero Doppler line?
Part Number:IWR1642BOOSTHi,I found there are big noises around the zero doppler line in the range-doppler heatmap, as shown below:My question is how can I reduce the noise around the zero doppler?On...
View ArticleTPS65983B: How to implement virtual HPD on TPS65983B FW?
Part Number:TPS65983BHi, TeamWe met an issue, the Intel's FW is using virtual HPD for display port, if the customer use this Intel FW with our TPS65983B, the display will not work.Could you please help...
View ArticleUCC256301: Question about UCC256301 SIMPLIS Model.
Part Number:UCC256301Dear support member,I have a question about UCC256301 SIMPLIS Model.I opened UCC256301 SIMPLIS Model using SIMPLIS.But SIMPLIS showed error mesage at Command window.error mesage...
View ArticleTM4C1294NCPDT: About GPIO interrupt priority
Part Number:TM4C1294NCPDTHello.I have questions.Can I change the interrupt priority of GPIO?If yes, could you tell me how to do it?Regards,
View ArticleClik here to view.
BQ40Z50: Max current consumption in sleep mode
Part Number:BQ40Z50Dear Team,do we have max values for the current consumption during sleep mode of the bq40z50?Datasheet specifies typ values, but no max.Thanks and best regards,B
View ArticleTMDX5505EZDSP
can i debug this TMDX5505EZDSP with its usb only or do i need separate JTAG connection..they have mentioned that TMDX5505EZDSP tool has embedded XDS510 emulator for full source level debug...
View ArticleLinux/BEAGLEBK: How to make the customer am335x board both wired and wireless...
Part Number:BEAGLEBKTool/software: LinuxI built a cutomer board based on beagle bone black but added the wl1835 for wireless. I hope the customer board can use both wired and wireless network...
View Article