CDCM6208: LVDS output spec
Part Number:CDCM6208Hi all.Please tell me the following spec.Sorry, I could not find spec.LVDS 125.MHz output- The high voltage and low voltage of LVDS output.- Slew rate(0.63V~1.17V)Best RegardsSho
View ArticleTPS40428: Loop Compensation Tool for TPS40428
Part Number:TPS40428Hi Team,In datasheet of TPS40428, there is a mention about 'TPS40k Loop Compensation Tool', but I couldn't find it in 'Tools and Software' Folder. There is one such tool in TPS40422...
View ArticlePre-amplifier is needed for ADS1198 front-end in EEG application?
Hello everybody,I intend to use a ADS1198 front-end for my EEG acquisition application. I have read the datasheet that the ADS1198 has a maximum gain up to 12. However the EEG potential is typically...
View ArticleTPS386000: Power-up sequence on TPS386000
Part Number:TPS386000Hello support team. I would like to know one thing that on the TPS38600, the SENSE terminal can apply input voltage before the VDD applied? The target system to be such so I need...
View ArticleClik here to view.
TAS5760M: External Bypass Capacitor for Internal Linear Regulator
Part Number:TAS5760MHi,What are the concerns if changing the external bypass capacitors(C2, C3 and C7) from the 1uF capacitor to the 10uF capacitor for the internal linear regulator ?Best regards,Kato
View ArticleClik here to view.
FDC1004: Trouble initiating I2C communication between Arduino and 3.3V Slave
Part Number:FDC1004Hi to all, first post in here, please be kind. I'm trying to get into capacitive sensing and therefore need a stable communication between an Arduino and a TI FDC2114, which is...
View ArticleAWR1642: How to use the WRITE TO FLASH command without uinflash tool?
Part Number:AWR1642Hi,I try to develop the flashing tool for MP, and the reference document is swra551-page13. <Programming Serial Data Flash Over UART>Also, reference the e2e post as follows...
View ArticleJ6EVM5777: sch orginal design about J6EVM5777 CPU Board
Part Number:J6EVM5777Hi everyone,Where can I find the sch orginal design about J6EVM5777 CPU Board？ I have got the sch PDF, but I want to customize my own cpu board. It‘s really a cumbersome work to...
View ArticleClik here to view.
CCS/TMS320F28069M: Why at reset vector location braching instructions is not...
Part Number:TMS320F28069MTool/software: Code Composer Studioin documents its mention that when device reset the reset vector fetched from the reset vector location , but when I am debugging there is no...
View ArticleTPS2511: The output current is less than expected
Part Number:TPS2511Dear Sirs;I'm trying to use the TPS2511 IC for a circuit which should have 5 Volts and maximum 2.1 amp output depending on what the connected device demands.But I have a series of...
View ArticleMSP-SPEECH-RECOGNIZER: How much flash required for recognizing 60 words
Part Number:MSP-SPEECH-RECOGNIZERHi The MSP432 speech recognizer recognizes 5 words in demo. My customer wants to recognize up to 60 words. How much flash required? How about 1MB or 2MB?
View ArticleAutomotive MCU
Hi,Application - Electronics Fuse• automotive grade controller• I/O <30• PLL based clock• 8 bit/32 bit• 3.3/5V power available.Kindly adviseWith thanks and regards,Anand
View ArticleLinux/DRA745: how to set omap mmc high speed in 192M ?
Part Number:DRA745Tool/software: LinuxHi, I try to set omap mmc hs mode in 192M , it's fail. The error is:"omap_hsmmc 480b4000.mmc: ADMA err: ST_TFR, desc at 0xfd841008 follows the erroneous...
View ArticleClik here to view.
LAUNCHXL-CC1350: Memory overflow when external sensor is interfaced with...
Part Number:LAUNCHXL-CC1350Hi,I am try to interface an external Analog sensor to CC1350 launchpad.I have integrated the CC1350 adcbufcontinuous(with RTOS) code with sensor1350lp available in the...
View ArticleCompiler/AWR1243BOOST: Ramp slope setting by DFP_09
Part Number:AWR1243BOOSTTool/software: TI C/C++ CompilerHello,I tried to set Ramp slope about 35MHz/usec by changing "mmwaveconfig.txt" in "mmwave_dfp_00_09_01_06". I just changed the parameter...
View ArticleAM3352: I2C clock stops when executing program on NOR(XIP),
Part Number:AM3352Hi,We have a strange issue with AM335x I2C operation with GPMC TIMEPARAGRANULARITY ="0".I2C works normal when we execute code on DDR3, but this issue(The I2C Clock output stops)occurs...
View ArticleLMR23630: Power consumption and efficiency optimization at light load
Part Number:LMR23630Dear E2E Community,My customer is testing our DC/DC through the LMR23630EVM.The design constaints are low cost, small size, high efficiency for few mA output, 8V to 36Vmax -->...
View ArticleAM26LV31E: AM26LV31E Differential Line Driver doubt
Part Number:AM26LV31EHi We are used AM26LV31E Differential Line Driver for one of our project.I have following doubts1) I gave 3.3V DC signal at the input side what should be my expected output...
View ArticleRTOS/TDA3XEVM: control of RGB gain , contrast of display from TDA3xx
Part Number:TDA3XEVMTool/software:TI-RTOSHi Everyone ,I like to know is there any possible ways to control the RGB gain, brightness / contrast of the display from the TDA3x . I like to know whether...
View ArticleCompiler/AWR1243BOOST: Sub frame and Dynamic Chirp Config parameter
Part Number:AWR1243BOOSTTool/software: TI C/C++ CompilerHello,I want to know about the sub frame and dynamic chirp configuration. These parameters are set by "mmwaveconfig.txt" in mmwave_dfp_00_09. But...
View Article