Issues with OpenCV installation on Beaglebone Black!
Hi everyone,Since I'm not quite familiar with Angstrom (originally shipped with the board and had OpenCV pre installed), I've installed Ubuntu 13.04 (Specially configured for BBB) and started working...
View ArticleDoes Code Composer free version allow programming the MSP430?
Hi All,I download the CodeComposer free version and run on the MSP430. I found that under the "Run" pull down, the "Load" is inactive, I can only choose "Debug". Does that mean that I can no program...
View Articlebeagleboard xm project
i am doing a project on beagle boardxm i required so information that how to interface BBXM to DSp
View ArticleClik here to view.
MSP430G2553 Point type variable runing issue in diffrence chip
Hi,I met a critical issue of MSP430G2553, the detail as below, any body can help me to analyse it? thanks very much..Processor：MSP430G2553Compiler：IAR Assembler for MSP430 5.30.1 (5.30.1.50284)Iusse...
View ArticleQuestions regarding u-boot memory mapping
Hi,Looking at include\configs\ti8168_evm.h, the memory mapping for the DDR3 is as follows:#define CONFIG_NR_DRAM_BANKS 2 /* we have 2 banks of DRAM */#define PHYS_DRAM_1...
View ArticleSolder Stencil Thickness for TMS5703137ZWT
Please confirm if there is a recomended solder mask stencil thickness for the TMS5703137ZWT. In a TI document titled “Flip Chip Ball Grid Array Package Reference Guide” (Literature Number: SPRU811A,...
View Articlenvr usecase
in the DM816x DVR RDK UseCaseGuide 32D1 DecodeDisplay doc，i seeMultichannel Decode & Display (NVR) Use-case i want to konw where is the case，why it say nvr？i want to learn about nvr usecase.do you...
View Articlequestion about using the DDR_PLL of DM 8168
Hi,My DDR3 can't work stable on the the 675MHz and the 796MHz, now, it can work stable on the 531MHz, however, it is unacceptable to us.Now, I want to adjust the PLL of DDR, and I found some setting in...
View ArticleKinect + BeagleBone Black
Hi everyone,Is there anyone here who has used the BeagleBone Black to receive and store the data stream from a Kinect Sensor?We are trying to use OpenNI drivers for Kinect in Ubuntu on the BeagleBone...
View ArticleVPSS M3 load increases if Video M3 is enabled
Hi,I am using Netra (TI8168-GP rev 1.1). If i do 2 1080i captures and scale only, the VPSS M3 load is ~15%. If Video M3 used, the VPSS M3 load shoots up to 65% - 70%. Also, the VPSS performance...
View Articlemmc_send_cmd: timedout waiting for cmddis!
Hi all,I am working on a custom board equipped with the DM8168.We have included 1Gbytes of DDR3.I am currently testing the board with a DDR PLL set at 400Mhz, slower that the EVM settings.So we...
View ArticleAM3892 DDR2 MT47H64M16HR
Hi Sir,i am using customized board based on TI8168 board. Here 1. i did not find c code for DDR2 stuff in board-ti8168evm.c. Is this correct place to check Low level initialization of DDR2 interface.If...
View ArticleGetting access to the SPI interface on am335x Starter Kit using the...
Hi Guys,I have been at it more than a week now and I can't seem to figure out how to get access to the SPI interface on the am335x Starter Kit using the Jellybean Guide here:...
View Articlec6000 parser gtest segmentation fault
Hi there,I have been getting the following error:INTERNAL ERROR: /home/smithr/ti/TI_CGT_C6000_7.4.6/bin/acp6x experienced a segmentation fault while processingWhen compiling the following code with...
View ArticleCC1125 Board Design
Hello,i have developed my own layout for the CC1125 Transceiver. I started with the layout of the CC1125 Cat1Reference Design. I used 0805 components. My problem is that i receive not the correct...
View ArticleCC2530 falling edge interrupts strange behaviour
Hi,I designed a board with CC2530 but having problem with falling/raising edge interrupts. Below I attached shortened code I used for testing and PCB design for an overview.Interrupts are detected...
View ArticleExtra components
Sir, We found that we may require some more ic's for our project which we encontered while in progress of our project and did not know about them at the time of component selection for IADC on or...
View ArticleGreen LED for reflective applications using AFE4490 / AFE4400
green LED can be used as a reflective pulse detector design of the afe4400???
View ArticleMultiple RI-STU-MRD2 in near enviroment
We are looking for a solution to operate several RI-STU-MRD2 devices with a small distance.We use up to 16 devices with seperate antennas and the distance between them is 20 cm.We use round antennas...
View ArticleLED Brightness Control
I'm going to design IR remote based LED brightness control circuit?.....could you pls help me for design?
View Article