Clik here to view.
AM5728: AM5728 Block Diagram
Part Number:AM5728Hello, I'm trying to find a block diagram of the AM5728 which should look something like this:This one is for the AM5K2E02. Can anyone help?Thanks,Joe
View ArticlePGA460: Air-Coupled Ultrasonic Transducers & Transformers Listing
Part Number:PGA460Air-Coupled Ultrasonic Transducers & Transformers Listing for PGA460The following tables lists readily available ultrasonic transducers and transformers which are compatible with...
View ArticleAWR1243: Synthesizer Sweep Bandwidth
Part Number:AWR1243Hi, I understand that there are separate VCOs covering 76-77 GHz and 77-81 GHz.In this scenario, is it possible to sweep from 76-78 GHz even though this sweep bandwidth would...
View ArticlePGA411Q1EVM: Mounting Hole coordinates
Part Number:PGA411Q1EVMHello Team,I have a customer requesting the XY coordinates for the EVM. Is this information available? Thank you. Regards,Ed
View ArticleDP83849IF: How do I configure a DP83849IF to interface for a copper ethernet...
Part Number:DP83849IFHello,I am working a a redesign that uses a Lantronix Wi-PORT NR that takes a UART input and creates a 100BASE-TX copper ethernet connection. These copper ethernet signals are then...
View ArticleClik here to view.
LMH6551: OP AMP Draw too Much Current
Part Number:LMH6551Hi, In my new design, the op-amps LMH6551 draw too much current from positive and negative supply.Here is the schematic of the circuit. (There is 100nF between each VCP pin and...
View ArticleTPS65910: RTC without external oscillator / crystal?
Part Number:TPS65910When using the internal RC oscillator, the RTC in the PMIC appears to loose 1-2 seconds every few minutes; The output frequency is 32.0kHz as expected per the datasheet.After...
View ArticleTPS65912: Unable to program PMIC when connections change.
Part Number:TPS65912Please consider these 2 scenarios:1)EN1_DCDC1_SEL pin connected to an external wire for testing purposes but, for this particular case, no signal is inputted.INT1 is also connected...
View ArticleRTOS/66AK2H12: c++ try()/catch()
Part Number:66AK2H12Tool/software:TI-RTOSAre try()/catch() constructs and throw() supported and if so can someone point to documentation?Thanks,Mike
View ArticleDP83822H: TM4C129XNCZAD and DP83822 transformerless configuration unreliable
Part Number:DP83822HHello all,I have implemented a DP83822 tm4c129x combination and connected the DP83822 in rmii mode to its mac. The tiva is using a stock lwip config from tivaware and we have coded...
View ArticleRI-CTL-MB2B: TIRIS Reader Manager (TRM) software - available for download?
Part Number:RI-CTL-MB2BI have an old board that failed and I need to program the spare one. Is the software TIRIS Reader Manager (TRM) still available for download? This software is mentioned in the...
View ArticleBQ20Z80A-V110: absolute capacity and remaining capacity stop decrementing at...
Part Number:BQ20Z80A-V110We are having trouble with the gas gauging accuracy on the BQ20Z80 V1.10. It appears that on discharge that the absolute capacity and relative capacity both stop decrementing...
View ArticleRTOS/TM4C129CNCZAD: After waking up from hibernation and performing soft...
Part Number:TM4C129CNCZADTool/software:TI-RTOSHi all,I hope you are doing fine.I am working with TM4C129XNCZAD hibernation mode and am having issues with soft reset after waking up from hibernation. I...
View ArticleRTOS/66AK2H12: Compiling C++
Part Number:66AK2H12Tool/software:TI-RTOSI just posted a question regarding c++ try/catch but I guess the bugger question is guidelines on compiling/linking c++ classes in general.I am trying to port...
View ArticleTS5V330C: part use for non-video applications
Part Number:TS5V330CHi,I would like to know if we can use this switch generically for analog applications.I've been using the NXP NX5DV330PW, and observed strange behavior. This TI part is listed as a...
View ArticleRTOS/CC2640R2F: How to configure an interrupt
Part Number:CC2640R2FTool/software:TI-RTOSHello,I started with a Simple BLE Peripheral project and I'm trying to add an interrupt that when triggered would call a function that would talk to EEPROM...
View ArticleWhat's the best evaluation board to start a Bluetooth/WiFi project?
Hi,I have a project to pair a cell phone to a MCU through Bluetooth and am looking for a Blue tooth evaluation module. Is CC2640R2F the best option for beginners? Do you think if it's better to have a...
View ArticleCCS/CC3100BOOST: Trouble with example mqtt
Part Number:CC3100BOOSTTool/software: Code Composer Studiohello ,i am working with the cc3100boost , i want to run a client for mqtt , i was based in the examples in SDK folder cc3100 , but i have...
View ArticleAM1808: EMAC HOSTPEND interrupt recovery
Part Number:AM1808Hi,I wanted to confirm that the only way to recover from a HOSTPEND interrupt, which are triggered by errors in packet buffer descriptors, is to do a HW WARM RESET of the chip. Is...
View ArticleCC2564: Is Slow Clock Necessary?
Part Number:CC2564Hello,I have a customer design which replicates the BT-MSPAUDSINK-RD.However, my customer was thinking about removing the 0 Ohm between the MSP430 and the CC2564 SLOW_CLK_IN. Is this...
View Article